Starline car alarm operating instructions. "Starline A9": programming the key fob. Car alarm "Starline A9": instruction manual

home

Signaling

Car owners try to protect their vehicle from break-ins or theft. For this purpose today they use various systems alarms. One of best options security equipment today it is considered "Starline". When developing this car alarm, the creators used the latest developments in the field of signal transmission. Special encoding almost completely eliminates the possibility of intelligent hacking. The dialogue message of the system with the control panel (key fob) allows the driver to fully use the functions included in the device by the manufacturer.

How to set up the Starline alarm system is described in detail in the instructions. The driver should familiarize himself with its main functions. Only after carefully studying the user manual will the car owner be able to fully operate high-tech equipment.

general characteristics

The Starline A91 car alarm is a dialogue message system. Radio control is performed using unique coding, which eliminates the possibility of hacking. The system has more than 60 functions. The ability to autostart and warm up the car engine significantly increases comfort.

The communication signal range reaches 2 km in open areas. If there are obstacles in the signal path, this figure is reduced to 600 m. At the same time, the level of interference is significantly reduced due to the use of a transceiver with 128 radio transmission channels.

The operating instructions for the Starline alarm system must be carefully studied by the owner vehicle. This guarantees that the system will function normally and its management will be comfortable.

"Starline A9" is used at temperatures from -45 to +85 ºС. This is a high-quality, durable car alarm that is relatively inexpensive.

Technical requirements

The Starline A91 alarm system can be installed in cars with a diesel, turbocharged or gasoline engine. It is compatible with both automatic and manual transmissions. The equipment requires a 12 V battery.

It is recommended to install the central alarm unit under dashboard. In this case, the length of the connecting wires will be minimal. The block should be firmly secured to flat surface. The wires must be approached in such a way as to prevent drops of water from entering the device (they can flow down the conductors).

The transceiver with antenna must be installed at a distance of at least 5 cm from metal parts body Most often they are mounted on the windshield or under the dashboard. For the system to work correctly and be reliable, it is better to entrust its installation to professionals.

Keychain

The Starline alarm system, the factory settings of which can be changed according to your own needs, is controlled using key fobs. The set includes 2 remote controls. The first key fob has an LCD display, and the second one has only buttons. The interface has been translated into Russian for the convenience of domestic users. This facilitates operation and makes the dialog message intuitive.

Up to 4 key fobs can be stored in the system memory. The delivery set also includes a cover for the control panel.

The key fob allows you to control and program all alarm functions. The most popular commands are arming and disarming, autostarting the engine or activating it using a timer.

The Starline A91 alarm system, the key fob of which is configured by the user, has many programs that are necessary for comfortable use.

Setting up the key fob

All key fobs are registered in the alarm memory in one setting. There is a special procedure for this. The car security mode must be turned off. You need to find the Valet button. We press it 7 times.

After this, turn on the ignition. 7 beeps will sound. This means that the system has entered the mode of binding key fobs to the control unit. Most often, this is necessary if the control panels for some reason do not communicate with the central control device or the driver bought a used car. In this case, the Starline alarm is re-programmed. The settings are reset automatically. The user can do this remotely if desired.

On the key fob there are buttons II and III. They are clamped at the same time. A signal will sound indicating that the key fob is activated. The same manipulations are performed with the remaining remote controls.

Setting the time

After linking the key fobs to the control unit, you can begin to use them. First of all, you should set the time. This procedure is performed exclusively using the key fob. There is a specific algorithm for this, prescribed in the instructions.

The Starline alarm, the setting of time and other functions of which is clearly explained by the manufacturer, is considered one of the simplest in the field of programming. To set the time, you need to hold down button III. The clock icon on the display will flash. To decrease the readings, press the I button, and to increase the readings, press the II button. Then the minutes are adjusted. To do this, press button III again. Setting the time will allow you to subsequently set a timer, autorun and other functions.

Engine starting programs

Instructions for setting up the Starline alarm system allow you to set the necessary functions when starting the engine. Using the key fob, you can remotely turn on the car engine, as well as extend its operation. It is very comfortable. In the morning, you can drink a cup of coffee at home while the car warms up.

In addition, the engine can be turned on using a timer or alarm clock. The driver has the opportunity to set autostart parameters independently. The engine will turn on once a day or after a certain amount of time (2, 3, 4 hours).

A motor control function is provided. To do this, the system tests the signals of the generator, tachometer, as well as voltage changes in electrical system auto. The key fob displays information about the duration of engine operation. When enabling the autostart functions, the driver must comply with all safety requirements.

Safety

The operating instructions for the Starline alarm indicate a number of requirements. The driver must comply with them fully. This will ensure complete safety of the car, as well as avoid accidents and troubles.

You need to park your car in an open, clearly visible area. At the same time, do not forget to turn on the handbrake. The automatic transmission lever must be set to the PARK position, and the mechanics - to neutral mode.

Do not start the engine automatically if there are people in front or behind the vehicle. It is unacceptable to leave the key fob in an easily accessible place where it can be reached by children or untrained persons. All vehicle systems must be in good working order, have sufficient fuel and Supplies.

Service functions

Setting up the Starline alarm system allows you to use many service functions. The user selects the most suitable programs for himself. The most popular are the following modes.

If the driver installs the silent security function, if his vehicle is encroached upon, the siren will not go off, but the relevant information will be sent to the key fob. This will allow you to catch the attacker red-handed. You can also configure silent exit and entry into security mode.

You can program a function where, if accidentally turned off, the system automatically returns to its previous mode. You can also control lighting, ventilation and heating. Their automatic operation is configured.

The key fob buttons can be locked to prevent them from being pressed accidentally. One of required functions is the location of the vehicle. You can also remotely erase lost key fobs from the alarm memory. There are many programs that increase comfort and safety.

Malfunctions

Configuring the Starline alarm system, done properly, allows the system to perform its assigned functions to the fullest. However, there are several types of malfunctions that can occur during operation of the alarm.

Most often, drivers note its false alarm. In this case, you need to correctly configure the sensitivity sensor of the control unit. It may be set to the maximum position or the sensor may not be mounted correctly.

It also happens that the control unit does not respond to key fob signals. They need to be linked to the system again. Perhaps the battery in the key fob is dead. Sometimes you need to purchase a new remote control.

It happens much less often that the alarm does not close door locks. In this case, the malfunction can only be repaired by a specialist.

Having examined how the Starline alarm is configured, the driver will be able to fully use all its functions. By following the instructions, the car owner will ensure the reliability and stability of the system.

Every year, new car alarm models appear on the market, radically different from previous models in terms of internal functionality. The StarLine A9 product, which has new software settings and additional options, was no exception.

Equipment

The company has gained trust due to the fact that it produces the most complete sets equipment and guarantees easy and easy installation. In particular, the StarLine A9 alarm package includes:

1 control key fob with LCD display;
1 additional keychain remote control;
processor unit;
module with antenna;
various sensors for installation (engine temperature, hood temperature and others);
instructions for use and warranty card.

What’s noteworthy is that the additional car remote control key fob comes without feedback. Most often, it is used in case of loss of the head unit. It has only 4 buttons used to open and close doors and start the engine.

According to experts, the StarLine company offers its customers maximum car protection with a set additional functions(timer, alarm clock, auto start, panic modes, etc.) at affordable prices.

Three button control

The control key fob has a display on which you can easily see all the symbols even in bright light. sunlight or in complete darkness. When you press a certain button, you can turn on the screen backlight for easier viewing.

The operating instructions for the StarLine A9 alarm system are simple, since programming only involves setting up three buttons located on the top surface. All of them have different functional significance, both individually and in a certain combination. The first button, located closer to the antenna, allows you to program the following functions:

access to programming of all basic commands;
starting and stopping the engine (remotely);
arming the vehicle while the engine is running.

The second button, located in the middle, allows you to program the current position of the cursor on the key fob and the command to open the trunk.
The third button, the farthest from the antenna, has four commands and mainly they have additional service functions. Their description looks like in the following way:

cursor control on the key fob;
interruption of audible warning signals;
changing modes in the alarm clock and timer, setting the clock and energy saving mode;
button programming.

It’s not difficult to understand how to control a key fob; the main thing is to initially set the values that are optimal for the owner when purchasing and change them only in certain situations. For example, a car warm-up timer on summer time absolutely not needed, but in winter there is an urgent need for it.

Button combinations

In addition to the fact that each button is programmed separately and sets a specific function, you can configure the key fob using a key combination. In the StarLine TWAGE A9 alarm system, the instructions for use included in the kit give full information about programming, there are many interesting modes.

The combination of buttons 1 and 2 allows you to configure panic modes, as well as car search. The essence of panic mode is the controlled activation of an alarm.

For example, this mode may be useful in a situation where the owner has discovered suspicious individuals near his car. By pressing the button, a sound siren is activated, scaring away ill-wishers. This is one of the simplest programmable panic modes, and there are up to three of them in StarLine keychain TWAGE A9.

The combination of buttons 1 and 3 has a less simple meaning: it allows you to customize the illumination of the key fob. By using the key combination 2 and 3, you can set the timer on your communicator if necessary.

Advantages and advantages of the model

Each new model An alarm system that appears on the market must surprise buyers and have new functions, otherwise there will be no interest in purchasing it. Thus, the StarLine A9 alarm system has the main advantage - intelligent automatic engine start. And also, some of the important advantages of this model include the following advantages:

many sensors (doors, hood, impact and other elements);
communication with the vehicle within a radius of up to 600 meters due to 128 radio channels;
possibility of starting the engine from mobile phone(with appropriate settings from specialists).

The StarLine A9 car alarm requires an AAA battery. The validity period directly depends on the frequency of use and many other factors, but on average it is from 3 to 6 months.
The equipment has a dynamic control code, that is, protection against selection and interception. Thanks to these parameters, vehicle safety reaches a whole new level.

The car alarm performs its functions either automatically or by signals from the key fob when buttons are pressed. Some of the provided functions and some car alarm settings can be changed by programming.

The Star Line Twage A9 car alarm has a 3-button control key fob with a liquid crystal display. The purpose of button 1 of the key fob is programmable.

The purpose of button 2 is selected quickly by moving the cursor on the key fob display using button 3. When you press the key fob buttons, the fluorescent backlight of the display turns on for a few seconds.

When the alarm performs any action, the corresponding information is automatically displayed on the key fob display and is accompanied by sound signals or vibration.

If more than one key fob is used to control the alarm system, then the status of the car and car alarm will be displayed only on the display of the key fob from which the last command was issued.

In case of inoperability or loss of the main key fob with two-way communication and a liquid crystal display, the system includes an additional 4-button control key fob without feedback with a standard range. Most of the functions and operating modes of the StarLine Twage A9 alarm can also be activated from this key fob, but further operating instructions are written for the case of using the main key fob with an LCD display.

Button 1

Programmable command (0.5 sec)
Remote engine start and stop (3 sec)
Activating the security mode with the engine running (3 sec)

Button 2

Command corresponding to the current cursor position on the key fob display (0.5 sec)
Unlocking trunk (3 sec)

Button 3

Controlling the cursor position on the key fob display (0.5 sec)
Interrupting key fob alarms (0.5 sec)
Turn on and off the mode for setting the clock, alarm clock, timer, energy saving (3 sec)
Programming button 1 (6 sec)

Buttons 1 + 2

Search mode (0.5 sec)
Panic mode (3 sec)

Buttons 3 + 1

Selecting the key fob alert mode (0.5 sec)

Buttons 3 + 2

Quick setting of key fob timer (0.5 sec)

The key fob with LCD display uses an AAA 1.5V battery. The operating time of the battery depends on the frequency of use of the key fob, on the frequency of operation of the pager, on the selected alert mode, and on the type of installed battery. The capacities of commercially available batteries may differ several times. Accordingly, the average operating time of one key fob battery can be from 3 to 6 months. When the battery is low, an icon is displayed on the display, which indicates the need to replace the battery of the Star Line Twage A9 car alarm key fob. The owner can replace the battery independently in the following order:

Open the cover on the back of the key fob and remove the old battery.
Briefly press button 1 of the key fob.
Install new battery, observing the polarity, and close the lid. ( Correct position batteries are indicated on the key fob body under the cover).
After replacing the battery, adjust the clock and alarm readings. Re-programming of button 1 of the key fob is not required.

Button 1

Turning the security mode on and off (0.5 sec)
Control channel No. 3 (3 sec)

Button 2

Starting and stopping the engine (0.5 sec)
Extending engine operating time (3 sec)
Activating the security mode with the engine running (3sec)

Button 3

Search mode (0.5 sec)
Unlocking the trunk - channel No. 1 (3 sec)

Button 4

Silent activation and disarming of the security mode (0.5 sec)
Control channel No. 2 (3 sec)

Buttons 1 + 2

Panic mode (0.5 sec)

Buttons 1 + 3

Disabling the shock sensor (0.5 or 3 sec)

Buttons 1 + 4

Enable service mode (0.5 or 3 sec)

Buttons 2 + 3

Enabling temperature trigger mode (0.5 or 3 sec)

Buttons 2 + 4

Enabling daily automatic start mode (0.5 or 3 sec)

Buttons 3 + 4

Enable anti-robbery mode (0.5 or 3 sec)
Recording a key fob in programming mode (3 sec)

The four-button key fob without feedback uses a lithium battery CR2032, ZV. The operating time of the battery also depends on the frequency of use of the key fob and the type installed element. When the battery is discharged, it must be replaced. The battery must be replaced in the following order:

Unscrew the screw on the bottom cover of the key fob and open the cover.
Remove the old battery and install a new one in its place, observing the polarity.
Close the key fob cover and tighten the fastening screw.

LCD display of StarLine Twage A9 car alarm key fob

Icons with letter designations - indication of commands, modes and alarm functions

Anti-robbery mode (on/off)
Additional channel 3 (on/off)
Autostart mode based on temperature (on/off)
Daily auto start or alarm start mode (on/off)
Remote engine start/stop (on/off)
Silent security mode without confirmation sounds when turning the mode on/off (on/off)
Security mode with sound signals (on/off)
Remote shutdown of shock sensor
Valet service mode (on/off)
Indication of vehicle status and interior temperature
Additional channel 2 (on/off)
Remote trunk release

Icons with digital designation - indication of the status of the StarLine A9 alarm system and the vehicle

Indication of low battery key fob
Activating additional channel 2
Autostart mode based on temperature
Engine started
Trunk open
The doors are open
Vibration alert mode
Valet service mode
Automatic switching of the security mode
Silent security mode
Security mode with sound signals
Hood open
Body impact (shock sensor level 1 or 2)
Parking brake released 15.Locking the doors
Unlocking door locks (including when opening doors)
Standby mode (only the key fob receiver works)
Indication of command transmission by key fob
Call from car
Key fob power saving mode enabled
Turning on the ignition
Alarm on
Time of day - RM
Time of day - AM
Daily auto start or alarm start mode
Indication of time, temperature and autorun modes
Temperature scale display (Celsius)
Countdown timer included

Programming button 1 of the key fob

The purpose of button 1 of the key fob is programmable and can be changed by the car owner himself an unlimited number of times. For ease of use of the alarm system, it is recommended to program this button to turn on/off the security mode.

Programming is carried out in the following order:

In the future, when using the alarm, a short press of button 1 of the key fob will lead to the execution of the command assigned to it (turning the security mode on and off). When the button is pressed, the icon corresponding to the programmed function will light up.

Note. To reprogram the assignment of button 1, you need to do the described procedure again. The assignment of button 1 will be replaced with the new one. Further, the operating instructions are written taking into account the fact that button 1 is programmed to turn the security mode on and off.

Purpose of button 2 of the key fob

The purpose of button 2 of the key fob is determined by the current position of the cursor on the key fob display. The cursor is moved by pressing button 3 of the key fob in the following order:

Quickly press button 3 of the key fob two or more times to start moving the cursor. Pausing and quickly pressing button 3 on the key fob again changes the direction of cursor movement.
When you press button 3, the cursor will cycle through the icons indicated by letters on the display diagram. By successively pressing button 3 of the key fob, set the cursor to the position corresponding to the desired command.

A subsequent short press of button 2 of the key fob will cause the StarLine Twage A9 car alarm to execute the selected command.

Automatically return the cursor position to the CHECK command

For ease of use of the key fob and to prevent accidental activation of alarm modes and functions, 10 seconds after the last press of the key fob buttons, the current cursor position automatically returns to the CHECK command. The CHECK command for monitoring the vehicle condition and interior temperature does not change the alarm state and is the most frequently used during operation.

How to protect your car from theft? Today, this question worries every car enthusiast, and therefore the range of security systems offered to help him is constantly expanding. What to bet on? Attractive characteristics or at a budget price? The Starline A9 alarm system saves the car owner from making a decision (it successfully combines both the first and the second).

100% protection

The car security system of this model is rightfully considered one of the best. And there is a reason for this: a high degree of protection. This enviable security is due to two factors:

Complex original encryption principle. It is this that is the basis of dynamic code, which is reliably protected from interception. It is almost impossible to crack an individual cipher (but the manufacturer decided to play it safe and enhance the effect with the help of a non-standard solution).
Extraordinary innovative approach . This car alarm model also successfully applies the principle of zoning. Each individual area is protected (engine engine, parking brake, hood, doors, trunk, windows, ignition switch). And a specific device (switch, sensor, relay) is responsible for this. All information about an attempt to break into or cause harm is displayed on the alarm key fob. Alarm signals are activated when any of the above zones is affected.

Impeccable work protective functions is also due to the fact that the state of all elements of the system is constantly under control. The failure of one of them is diagnosed by the device itself in a matter of seconds (the car owner learns about existing problem immediately after their discovery). This option (self-diagnosis) completely eliminates any risks (provided that the car owner takes timely measures necessary measures to eliminate them).

Luxury comfort

Another advantage alarm system starline a9 lies in her ability to combine business with pleasure. It is replete with options that make life much easier for the car owner and significantly increase the degree of comfort during operation of the vehicle. Such noteworthy functions of this security system model include:

Autorun. Starts the engine at a certain time (the setting can be made in three directions: depending on temperature regime, wait timer, alarm time)
Anti-robbery mode. It is triggered when, after opening the driver's door, confirmation of the owner's indication code is not received; after a specified number of meters, the system blocks engine operation.
Immobilizer mode. Relevant for those who forget to press the buttons on the key fob step by step; it is activated after 30 seconds of inactivity on the part of the driver (it blocks the engine half a minute after turning off the ignition).
Gsm starline module. Allows you to control the alarm from your mobile device, as well as receive messages about the system status to it.
Indication. The alarm key fob can replace a clock, an alarm clock, and a timer; it will also inform you about the operating time of the engine (a motorist may also need such information).

These are not all the capabilities of this model; the table shows only the most popular ones.

The energy efficiency is also impressive. Situations when the key fob does not respond to the commands of its owner are most often associated with wear and tear of its power elements; in the Star Line A9 control panel, the batteries last for at least 2 months (usually up to six months).

Installation without problems

Car alarms of this brand and model are also good because they can be installed independently. This process can be described as complex and simple at the same time. The difficulty lies in the fact that it involves a large amount of work that must be performed in accordance with a strict algorithm of actions, including:

location and fixation of system elements(recommendations: it is advisable to mount the central unit under the dashboard, the transceiver module on the windshield, a shock sensor anywhere in the cabin, an LED indicator near the instruments, temperature remote sensor on the motor body, siren in engine compartment with the horn facing downwards away from highly heated internal combustion engine parts);
connection diagrams(laying wires, installing electrical wiring connections, connecting the circuit responsible for the operation of sound and lighting equipment, auto-start systems, door activator, locking system, engine blocking, monitoring engine operation using one of the options: tachometer, on-board voltage, generator).

The ease of installation of Starline A9 lies in the fact that the instruction manual, included with each sold product of this type, gives a clear, detailed idea of everything related to its installation. In it you can also find a description of the reasons that could lead to incorrect, unstable operation of the installed security system (errors made during the installation process).

Effortless setup

Without exception, all owners of cars that have an alarm system of this model are interested in two important questions: how to link the key fob to the system and how to configure the necessary parameters for each of the modes offered by the manufacturer. To help the car enthusiast detailed instructions, concerning points of interest to him:

Keychain binding. We act step by step:
- start the car;
- press the “Valet” button(hold it until 4 beeps appear);
- simultaneously press buttons 1 and 2, release after 1 sound signal(for programming a key fob with an LCD display - the main control panel);
- simultaneously press buttons 3 and 4(relevant for recording additional key fobs).
Parameter programming. We follow the following algorithm of actions:
- press the service button 6 times with the ignition on(wait for the system response: 6 LED flashes + 6 sound signals);
- press the “Valet” button several times(before reaching a certain function);
- select the desired value, confirm the action with either a short or long press on buttons 1 and 2 (half a second or 30 seconds);
- back to the start by pressing the service button;
- repeat the steps for all functions, requiring special settings different from the factory settings;
- exit programming mode(turn off and turn on the ignition again or wait for automatic shutdown, accompanied by 5 flashes of the side lights).

Convenient control

In order to competently drive a car security complex called Starline a9, you do not need to have any special education. The LCD keychain is a kind of picture book, you just need to choose the right picture. Another thing is the additional control panel (the keypad can be confusing). However, the operating instructions and instructions included in the alarm kit quick guide on application will simplify the task for the car enthusiast. These media vital information will help you find answers to all your questions. Everything is here: connection diagrams, installation maps, methods for linking and setting up the control panel (key fob), methods for programming options and parameters, and even a list possible malfunctions and methods for eliminating them.

Starline A9 has enough advantages. Why not take advantage of them!

The Starline A9 alarm system is very popular among drivers of different cars. The system is supplied with detailed instructions. It allows you to connect and configure the alarm. The manual also describes the principles of operating the system. Having studied user reviews and the instructions, we can highlight the basic principles of working with Starline A9. Programming the key fob will be a simple task. Advice from experienced car enthusiasts will allow you to complete the setup quickly. This will give you the opportunity to use all the options. The alarm can be configured to operate in autostart mode or without it. The blocking function can also be configured.

General information

"Starline A9", the operating instructions of which require study before installing the system and programming the key fob, is an alarm system with remote engine start. It has a two-way radio communication channel. Its range on unobstructed terrain is 600 m. In pager mode, this figure increases by 2 times.

Radio signal coding is dynamic. The selection of control commands is carried out according to the cursor principle. Each command is controlled by its own button. It is displayed on the key fob display. The system provides sound and vibration alerts.

In addition to basic data about the condition of the car, the key fob shows the user the time, temperature in the cabin, and an alarm clock.

The presented system can be installed on cars with diesel, gasoline or turbocharged engines. The gearbox can be automatic or manual.

Safety regulations

When using the functions of remote or automatic engine start, control of machine components, it is necessary to follow the safety precautions for using the Starline A9 system. The instruction manual clearly indicates them.

It is important to park the car in a clearly visible area. In this case, it must be set to the parking brake. The automatic transmission lever should be in the PARK position, and the manual transmission lever should be in neutral.

You cannot start the engine without the driver in the cabin, if there is someone in front or behind the car. The key fob must not be given to children or persons who do not know how to operate this device. The machine must be in good condition, its system must have a sufficient amount of all consumables and fuel.

Control key fob

The built-in alarm functions are performed automatically or through signals from the key fob. Some of them can be changed. The procedure is prescribed in the instructions for the Starline A9 system. Programming the key fob is simple. For this, the device has three buttons. Information is displayed on a liquid crystal display.

The vehicle can be controlled using one or more key fobs. If you lose the main device with the screen, you can use a spare remote control. This is a key fob with buttons that does not have the function of providing information to the user. With its help you can control almost all functions of the system.

If car owners use several key fobs with a display, then all information about the state of the car and alarm systems will be displayed on the screen of the device from which the command was issued.

Purpose of the buttons

Setting up the Starline A9 key fob with a liquid crystal display is done using three buttons on the case. Their combinations make it possible to control system functions.

The I button can enable a programming command if pressed once quickly. By holding it for 3 seconds, the driver remotely starts or stops the engine. The user can turn on the security mode. To do this, with the engine running, I also hold this button for 3 seconds.

Button II, when pressed briefly, sets the position of the cursor on the screen. If you hold it for 3 seconds, the trunk will open.

Button III also allows you to control the position of the cursor with a short press. It interrupts the key fob alerts. To do this, hold it pressed for 0.5 seconds. To turn on or off the clock, alarm, and energy saving mode, hold this button for 3 seconds. If you hold it down for 6 seconds, you can enter the I button programming mode.

Pictures on display

All information about the state of the car and the alarm itself can be viewed on the display of the Starline A9 system. The icons on the key fob will help you navigate the setup and control modes. The instructions clearly state which picture corresponds to which function.

Indication of commands and modes is displayed at the bottom of the screen. You can list it from left to right for a general idea of the functions of the device. To fully understand the purpose of each of them, you need to carefully study the instructions.

The first picture, which is on the left, corresponds to the anti-robbery mode. If it is on the display, this command is enabled. Next is the function of additional channel 3. Moving into right side, you can see the motor autostart mode based on the temperature indicator. Next comes the function of daily autostart or turning on the engine with an alarm clock. This picture is followed by remote turning on or off of the motor.

This is followed by silent security modes. In this case, confirmations do not work. Next picture corresponds to the security function with a sound signal. This is followed by a shutdown at the distance of the shock sensor.

A little further to the right is a picture of the Valet service mode. It is followed by a picture indicating the status of the vehicle systems and interior temperature indicators. Next there is additional channel 2. The remote trunk opening completes the chain of pictures.

Button I

The I button on the main key fob is user programmable. This can be done an unlimited number of times. Most often it is used to turn off or turn on the security mode in the Starline A9 system. Programming a new key fob is easy.

Use button III to move the cursor around the screen. When the desired mode is selected, for example, turning on the security function or any other, the movement stops. Button III is held for 6 seconds. First, two beeps will sound. Then 3 more. Then the I button is pressed to activate the selected function.

After such programming, briefly pressing the I button will turn on the previously selected mode. To set a new function for it, perform the above operation again.

Button II

You can also assign a function to button II. You need to quickly press button III several times. The cursor will move clockwise. If you stop for 1-2 seconds and continue moving, it will move counterclockwise.

The pictures listed above will be selected one after another. When the cursor reaches the desired program, movement with button III is stopped. To execute the selected program, the user presses button II.

10 seconds after pressing any button, the cursor will return to its original CHECK state. This command monitors the condition of the car and the temperature in its interior. It does not change the alarm state. Knowing this, the user will not have a question about how to view the temperature on the Starline A9 key fob. During operation, this command is the most popular.

Setting the clock

When starting to work with the system, you need to learn how to set the time on the Starline A9 key fob. You need to hold down button III until two beeps appear. The clock on the display will flash.

To increase the digital value of hours and minutes, you need to press button I, and to decrease - button II. The transition from hours to minutes is carried out by briefly pressing button III.

After completing the settings, you need to exit the clock setting mode. To do this, hold down button III until one sound signal appears. According to the manufacturer's instructions, you can set the alarm or timer.

Recording codes

The driver can independently enter “Starline A9” codes into the system’s memory. The key fob is programmed in disarmed mode. You can link up to 4 remote controls. This must be done if the alarm system for some reason does not see the key fob signal or if the car was purchased with an already installed system.

To enter programming mode, you must turn on the ignition. The Valet service button is held until four sound signals appear.

First, set up the main key fob. Press buttons I and II on it. For additional remote controls without a display, press buttons III and IV. After successful recording of the first key fob, one siren signal will sound.

The same procedure is followed for all key fobs. The interval between recordings should not be more than 5 seconds. Otherwise, the programming mode will end automatically. Next you need to turn off the ignition. The success of the operation will be confirmed by 5 flashes of the vehicle’s side lights.

Engine starting

Many drivers are interested in how to start a car with a key fob. "Starline A9" when connecting an alarm system requires programming the type of gearbox. If it is manual, the wire loop is cut during installation (as indicated in the instructions). If the car is automatic transmission, this element is saved.

The engine type is also specified. There are two possibilities remote start motor. In the first case, you need to place the cursor on the corresponding icon on the display screen. Then you need to press button II. Or simply press the I button for 3 seconds.

When you first try to start, you will hear 3 siren beeps and 3 flashes of side lights. The key fob will emit a melodic signal. The icon on the display will be lit constantly. You can set the engine warm-up time.

Reset settings

Sometimes a driver may need information on how to reset the Starline A9 key fob. Actions are performed in a certain sequence. First the ignition is turned on. Next, the Valet service button is pressed 10 times. After this, the user turns off the ignition. The reset mode is entered if after these manipulations 10 siren beeps sound.

The service button must be pressed one more time. After this, another siren will sound. The driver presses the I button on the main key fob. A short beep will sound. This means that the reset has been completed. The system will exit the settings mode automatically after 5 seconds. will flash 5 times. The key fob will emit a melodic signal.

Having considered the features car alarm“Starline A9”, programming the key fob is easy and simple. Before starting to work with the equipment, you must read the manufacturer's instructions. This will allow you to fully use the built-in functions. If necessary, you can return the system to factory settings. Key fob control will allow you to use security system the car is comfortable and complete.

Sections