home
Signaling
DIY wall hanging. How to make a wall hanger for a hallway out of wood

DIY wall hanging. How to make a wall hanger for a hallway out of wood

You can do without a hanger in the hallway or corridor only if you have a large closet, and even then not always. In private homes, it is more convenient to have “duty” clothes on hand - to jump out into the yard. Those that are mounted on the wall are more convenient: they take up less space. One thing is not encouraging: the prices for worthy specimens are considerable. Therefore, we will tell you how to make a wall hanger with your own hands. The models are different, different techniques are used, but they have one thing in common: they are easy to make, especially with detailed photos process and explanations. There are also diagrams and video tutorials.

From boards in the form of a tree

To our small hallway need a hanger. I don’t want to buy a regular one in the form of a bar with hooks - I don’t really like them, and my little daughter won’t be able to get them. Other options with a set of parallel boards are also not inspiring. There is a switch on this wall, so it won’t work without adjustment, and it’s not clear what it will look like. Therefore it was decided: I do wall hanger with your own hands in the form of a tree - trunk, branches. It fits into the interior. I will treat the wood with stain and varnish water based, the color should be close to the color front door.

So, two were purchased at the sawmill unedged boards 25 mm thick. There are markings on them - on one there is a trunk, on the other there are branches.

We take an electric jigsaw and cut out the blanks along the marked contours. Next is a turn of very dusty work - we sand the wood, while simultaneously adjusting the thickness of the joints with the “branches”. We used a drill with a rubber attachment and sandpaper. First the coarse grain, then the medium and fine grain.

Sanding is a dusty business

Once the result was satisfactory - it became smooth and the grain of the wood was clearly visible - it was time to stain. This is a mahogany color applied in four layers. After drying, we coated everything with water-based varnish. Three layers were applied at intervals of three hours.

200 mm nails were used as hooks. They were cut to the required length (they were different - longer for the top of the hanger, shorter for the bottom). The caps and rod were sanded for smoothness, and threads were cut on the lower part to the thickness of the board (25 mm). Holes were previously made in the “branches” and “hooks” were screwed into them.

Now all that remains is to fix all the parts on the wall. The walls are concrete, so we fasten them with dowels. First we attach the barrel and drill holes through it. Set aside the wood for now and insert plastic plugs for the dowels into the holes. Having placed the “trunk” in place, we screw it. Using the same technology we attach the “branches”.

It turned out well, and the color matches the door almost exactly. There are plans to build small shelf for shoes and bags. The entire cost of making this hanger was about $6 for the boards and $2 for the nails, about the same amount was spent on the dowels. There was stain and varnish, and the consumption was small.

Simple wall hanger made of laminated chipboard

The task is to make a cheap clothes hanger on the wall (for a rented apartment). Two boards of laminated chipboard () called “ furniture board" Two, because the price turned out to be low, and in the accessories department, where they were looking for hooks, they found some good brackets for very little money. We will use them for the second board - we will make a shelf for small items.

The tools you will need are a screwdriver or screwdriver, a drill, and a set of drills. Also, use a tape measure and a pencil to mark the places where hooks and brackets are attached.

After unpacking the boards, glue stains and some other incomprehensible stains were found on them. All this can be eliminated with a solvent. Take a soft white (not colored) rag and wipe everything well.

Next, mark with a pencil the places for the screws. Remove the hooks and drill holes. Drill - 1-2 mm smaller in diameter than the diameter of the self-tapping screw. The hole is necessary so that the work goes easier, and also so that the surface does not crack when twisting. We put the hooks in place.

Now it's the turn of the shelf. I set aside equal distances on one side and the other, attached the brackets, and marked the holes for fasteners. Drilled holes and installed brackets. All.

Now we attach it to the wall. The technique is the same, but with dowels: apply, mark the attachment points, drill. The drill is the size of the dowel. We insert the dowel plug into the hole, attach the hanger/shelf to the wall, and fasten it.

This DIY wall hanger was made in two hours (including the shelf).

Hanger with shelf

You can take the idea as a basis and use any other “hooks” and stops. This DIY wall hanger is made from two 25mm planed boards, two carpenter's squares and five hammers.

The wood needs to be dry, otherwise cracks may occur. Instead of squares, you can even use triangular pieces of a similar board. Important condition- Availability right angle. And instead of hammers, you can even fasten knots or, for example, cut wooden hangers, or any hooks. This option is just a gift.

Spare parts - hammers and squares

The two boards must be the same length. An exact match is important. Having adjusted the length, we process sandpaper the edges. There is a drill - we take the attachment, attach the emery and sand first with coarse grain, then with medium grain. Then we start marking. First, we mark where the stops will be attached. We divide the remaining distance by six, put marks - there are five of them. Just according to the number of “hooks”.

We mercilessly cut off the handles on the hammers. We cut it slightly obliquely to create a slight slope.

Using a drill, make holes in the center. The diameter of the drill is 1-2 mm smaller than the fastener used, the depth of the hole is no less than the length of the self-tapping screw.

The two boards must be connected at right angles. The installation step of the screws is 10-15 cm. We mark the places on the sidewall and transfer them to the end. High accuracy is required. We apply one to the other and transfer the marks with a finely sharpened pencil. We make holes according to the markings.

Drilling holes

We fold the boards at an angle of 90° and connect them with self-tapping screws. First we twist the two outermost ones, then the one in the middle, and then all the rest. The length of the screws is at least 75 mm (triple the thickness of the board).

Using the markings, we drill holes for the hooks.

We install angle stops. Since carpenter's squares were used, there were no holes in them. They were drilled - two at the top and bottom on each plank. There are 8 screws on one stop. We take them small - more than 20 mm, so as not to puncture the wood. Therefore, a large number of them are required.

The wooden wall hanger is ready. All that's left to do is paint it and hang it on the wall.

Based on this homemade hanger, other versions were made.

With more voluminous shelves

Video lessons

Several simple homemade hangers for the “handy” in video format.

Drawings and ideas for DIY

A simple hanger option for making yourself

The hallway is the first thing guests will see when they enter your home. Therefore, it makes sense to decorate the hallway walls in a non-standard and interesting way, thereby forming an unforgettable first impression. Original wall hangers in the hallway are an important and integral element of the interior. There will always be something to hang on hook hangers: outerwear, bags, umbrellas and other accessories. Some design ideas will help you move away from traditional solutions and transform the hallway!

Wall hanger in the hallway: types and features

Hanger in the hallway - simple and extremely useful design in the interior. If in a small hallway it is not possible to place a cabinet or wall, then a wall hanger will become optimal solution allowing you to store things and keep usable space free.

In the traditional version, a wall hanger is a bar on which hooks or pins are located. But even so simple design designers are constantly improving, changing, adding new functions and surprising with completely extraordinary designs. Often, the classic hanger model is made more spacious, equipped with additional recesses for small accessories and keys, trays for things, slots for correspondence and shelves for hats, movable elements are mounted, and instead of the standard rectangular one, the hanger is given a curved, curly or stylized shape. Many models of wall hangers are hanging mini-hallways that are attached to the wall.


A wall hanger for the hallway can also be made in the form of separate hooks located on the wall in a specific or chaotic order. This option is even more compact and flexible, which allows you to arrange a hanger even for very limited area. The main difference and advantage of individual hooks is the mobility of individual elements. After all, even a small wall hanger in the hallway cannot always fit into the existing space. Modern designer hooks for outerwear are very popular and are used in the interior not only for functional purposes, but also for original decor, which emphasizes the style and uniqueness of the room. In hooks, much attention is paid to design - unusual shapes of hooks, non-standard materials, bright colors and catchy decor. Such a hanger becomes the visual center of the hallway interior.


Types of fastening hangers and hooks

There are four main types of fastening:

  • classic with screws;
  • adhesive;
  • suckers;
  • magnetic.

The most reliable and common method of fastening is with screws. With this method of fixation, hangers and hooks can withstand greater loads. For constant use in the hallway, for heavy outerwear, it is better to choose this type of design. Fixing the hooks with suction cups or adhesive tape is suitable for use in the bathroom, kitchen or nursery, where the load on the hanger will be less than in the hallway. These types of hangers require a smooth surface, e.g. ceramic tiles, and the main advantage is that they do not spoil the wall. The magnetic method is used extremely rarely, since installation is a prerequisite metal surface in the hall.

Use in different interior styles

Wall hangers in the hallway and coat hooks are selected according to the interior style of the room. For a classic hallway, hangers made of wood or metal are suitable, preferably with a discreet design. In an interior dominated by calm pastel colors and decoration natural materials Such wall hangers will look very organic, only emphasizing the classics.

In the interior modern styles You can safely experiment with the shape of wall hangers or hooks. Any brave design options will favorably emphasize the relevance and originality of the interior. Stylized figures, abstract shapes, non-standard designs - the brighter the design, the more unusual the composition you can create.

Into the interior industrial style, growth or loft, hangers from water pipes or hooks made from wrenches.

A high-tech hallway can be decorated with futuristic metal structures.

Minimalism and Scandinavian style will withstand any design of hangers, but the main condition is their small sizes and the absence of unnecessary decorative details.

More photos of original wall hangers and hooks for inspiration:


















We come home and take off our outerwear. To keep it from lying around, we hang it on a hanger. This way, clothes don’t bother us and don’t create chaos in the apartment. You can always quickly find a jacket or coat by looking where all the clothes hang. If you have a small hallway and there is nowhere to put a closet, then a hanger will solve all the problems. This attribute happens different sizes. Therefore, you can choose a hanger, despite the size of the hallway. Their designs are varied, but you have the opportunity to make a hanger according to your own sketch.

Hanger necessary thing, if you often have guests. Guests can hang their things on it when entering your corridor. Hangers are usually located near the front door, so as not to walk around in shoes throughout the hallway. Now their variety is great. Finding a suitable hanger that fits into your interior is easy. You can make it yourself using an individual design.

For a hanger to perform its functions, it must be:

  • Convenient;
  • Light;
  • Reliable.

You have decided to make your own hanger. Then you need to know in advance what it should be. You need to remember what the hallway walls are made of.

If the walls are made of plasterboard, you should think about a floor hanger. Then you won't have to mount it on the walls. Mounting a hanger on plasterboard walls is difficult.

Installation on such walls involves the use of special equipment, tools and dowels. Such a wall may not withstand the load from a large number of things, then the hanger will fall.

Floor models have several hooks. If you hang things evenly on it, it will not fall. This attribute is light in weight and can be moved to a new location if necessary.

You can make a hanger with your own hands from simple materials: wood, fiberboard or chipboard. Then decorate it beautifully - paint it or apply a suitable design/ornament.

The most common material for making hangers is wood. It is easy to make a certain shape from it.

Birch is not the best best material for making hangers. Wood has a fragile structure, so when screwing in fasteners, there is a high probability of damaging the finished product.

Almost everyone has the materials you need in their home. A set of tools and materials for work: jigsaw, hacksaw, sandpaper, hooks, screwdriver, boards.

Take the boards the right size. You process the wood: you sand it. Then go over the entire surface with sandpaper until it is perfectly smooth.

You can decorate according to your taste. You can cover the boards with varnish or paint. Attach the hooks to the board using a screwdriver.

For fastening finished product There are two types of wall mounting:

First: You can attach the hanger to the wall by drilling through it.

Second: With reverse side Make hangers into loops and then hang them on nails.

The hanger is ready and can be used for its intended purpose.

We make original hangers for the hallway with our own hands

The hallway is the first room in the apartment. Therefore, guests pay special attention to it. You can add an original hanger to the interior of the corridor and make it yourself. This will attract the attention of people who decide to come to visit you. And you will place all their things on the original hanger: clothes, umbrellas, bags and various accessories. Transforming your hallway and making it beautiful is easy, quick and inexpensive.

Any person in the house will have unnecessary things that can be used to make a hanger. Boards, skis, boxes, old furniture - all this can be used as a basis for an original hanger.

You should attach hooks to the skis, screw the entire structure to the wall - the hanger is ready for use.

A clothes hanger can be:

  • standing;
  • Wall-mounted;
  • Consist of separate hooks.

For classic design In the hallway of the room, a wooden or metal hanger in discreet (natural) colors is suitable.

An original solution is a hanger consisting of separate hooks. They hang on the wall itself. Hooks can have an interesting shape, color and design. For example, in the form of raindrops arranged in a chaotic manner. You can attach the hooks yourself without using additional tools.

What are hangers and hooks used to attach?

Hangers and hooks have several types of wall mounting. You can attach them to the wall yourself without using special equipment or by applying it. Metal hooks are suitable for wooden hangers. They are fastened with additional fastening - screws.

Hooks for hangers can have the following type of fastening:

  • Suckers;
  • Special adhesive strip;
  • Magnets.

All three types of fastenings that the hooks are equipped with do not require much effort and time to install.

It is worth remembering that these types of fastenings may not support heavy clothing (fur coats, down jackets). These hooks are used to hang hats.

How to choose the right hanger for the hallway

Before purchasing or making a clothes hanger, you should keep many things in mind. You need to take into account the free space and design of the hallway of the room, where to put the hanger or at what height to hang it.

Tips for choosing a hanger:

  • It should be in harmony with the design of the room;
  • For lovers of minimalism, floor-mounted suit models are suitable;
  • For classic style wall-mounted models are suitable;

The floor hanger is lightweight. It can be quickly moved or removed. Many people choose this type of hanger for their hallway.

How to make a hanger in the hallway with your own hands (video)

Every apartment should have a hanger in the hallway. It is a practical attribute in the interior. Occupies less space than cabinets. Can hold a large amount of clothes. Each item hangs on a specific hook, and you spend less time looking for it. Everything you need to take with you outside - a bag, an umbrella, a hat, a scarf and a coat - can be in one specific place near the front door. Therefore, it is worth thinking about purchasing or making such a wonderful device for your hallway room.

Design a hanger for the hallway with your own hands (photo examples)

In a cozy home it is impossible to do without a hanger - floor, wall or ordinary hangers in the closet. But in addition to its utilitarian function, storing clothes in a straightened form is also a way to show your creativity, the opportunity to do something with your own hands for household use. An original do-it-yourself floor clothes hanger or original nailed hooks in the hallway - how can you do without them? To make the simplest tremmels for jackets or horns for hats, you don’t need to be a jack of all trades, all you need is a tool and a few creative ideas.

Hanger as an art object or decorative element

To quickly clean up your home by arranging things in your closet, it is important to have enough space to easily accommodate:

  • dresses and jackets;
  • hats and caps;
  • bags and belts;
  • scarves and neckerchiefs;
  • blouses and sweaters;
  • business suits;
  • outerwear for the off-season;
  • skirts and trousers.

But for each such thing you need a special device:

  • wall hanger;
  • hangers (trempels);
  • panel or shelf with hooks;
  • clothes hanger in the hallway;
  • rings and hooks for the closet for scarves and accessories.

It’s easy to build many types of clothes hangers - with your own hands, photo:

If you look through old things from grandma's closet or chest, there are probably some pretty interesting clothes hangers in there. Vintage trempels and homemade hangers, if they do not qualify as “antiques,” may well be the basis for renovation or even become a unique art object. No matter how hard they try to transform an old hanger, masters of folk crafts, needlewomen and just those who like to “get creative” with something! For example, a clothes hanger photo.

Hangers from grandmother's use were made in an era when plastic or plastic products were not released. An old wooden base can be used as an original decorative object, especially if there is no closet in the room. They can be transformed in any way or use any suitable technique:

  • decoupage;
  • original painting;
  • application for varnishing;
  • pasting posters, magazines, geographical maps etc.

It wouldn’t hurt to make soft “shoulders” for the knitwear on the old base so that it doesn’t slip or stretch. These simple devices It’s also easy to make “from scratch” from scrap materials. But if you need a wall-mounted base for wooden hooks or an original floor-mounted clothes hanger-rack, then you need materials, tools and woodworking skills.

Wall mounted wooden hanger

Although a wall hanger is the simplest device that is suitable for self-production, you should not make it crude and primitive. Even if you plan to use it temporarily, for example, in the country, it is still better to make it beautiful so that the wall-mounted clothes hanger decorates the house for many years.

For quality product will be needed good wood, board or scrap of a block, the required length - the width of 2-3 freely hanging trempels with jackets. The board for the base must be strong and dry, without cracks, and treated with antiseptics. On this basis you will need to stuff several hooks:

  • in line;
  • in 2 rows;
  • in 3 rows - in a checkerboard pattern.

The simplest single-row hanger is useful in any room:

  • on the back of the bedroom door - under dressing gowns;
  • in the bathroom or toilet - for linen while swimming;
  • in the pantry - for work or seasonal outerwear;
  • in the pool or sauna - under towels and bathrobes.

A child's room or a teenager's room also needs a simple wall hanger - teaching schoolchildren to be tidy, to hang everyday clothes on hangers so that they do not wrinkle.

Tip: The simplest hanger is a board with hooks and loops for mounting on the wall. But do not forget that it cannot be nailed to an unplastered wall or whitewash. An unprepared surface will cause clothes to get dirty. Therefore, they must hang them on the wall in an unfinished room under a hanger. wooden shield, plastic film or whatman paper. And wet outerwear will stain the wallpaper or painted wall on the prepared wall.

If you have any original idea Regarding the design of the product, it is not necessary to make it in the form of an oblong rectangular disk. A do-it-yourself wooden base for a wall-mounted clothes hanger can be made in the form of:

  • oval;
  • wave-shaped panel;
  • stave;
  • heart;
  • spirals, etc.

After making the base, the wood must be sanded and varnished or processed in another way. It is important that the wood does not give rise to splinters when using a homemade hanger. It is advisable to make the hooks or “nails” of the hanger in any way in an original way, will fit:

  • old wooden thread spools;
  • handles of broken screwdrivers, scissors and other household items;
  • specially planed hooks.

Hooks, “nails” or “holders” for a hanger do not have to be made of wood or metal; they can also be bought at a hardware or construction supermarket. Also suitable natural material- dry branches, twigs, cuttings or root cuttings. They must be cleared of bark, cut or sawed off excess, sanded and varnished.

Another standard hanger option is from wooden planks, nailed in parallel. They will become not only the basis for hooks, but also a decorative shield for clothes on a whitewashed wall or simply a beautiful piece of furniture. It will take a little more time to make, but this design looks more solid than just a board for hooks. And if you attach a visor to the hats, it will already be a full-fledged clothes hanger in the hallway with your own hands.

Homemade clothes hanger for the hallway

The hallway hanger should be enough:

  • durable and strong;
  • aesthetic;
  • roomy;
  • multifunctional.

Ideally - for a short period of the wall in narrow hallway should fit:

  • outerwear for all family members or guests;
  • hats;
  • umbrellas and bags;
  • shoes under clothes.

It is this versatility that is important to consider when building a homemade hanger for the hallway. Therefore, it is wise not just to make a board with hooks, but to decorate it beautifully:

  • shield with hooks for clothes;
  • visor for caps and hats;
  • shelf for shoes;
  • stand for bags and umbrellas.

Tip: The dimensions of such a hanger should not be arbitrary; they are measured against the part of the wall where the hanger should be located.

Usually a space of about 1 m in width is enough; the height of a clothes hanger in the hallway with your own hands should be greater than head level. There are 2-3 rows of hooks under trempels and outerwear, plus a visor (shelf) for hats. Reliability of connection The shelves of the side panel can be connected with strips at an angle of 45°C. The hanger must be attached to the wall with brackets or dowels.

Floor hanger rack

Another type of device for placing clothes at the entrance to a building is a do-it-yourself floor clothes hanger. You can often see them:

  • in the clinic office;
  • in the reception area;
  • in the hall or vestibule;
  • in an Internet cafe, etc.

They are usually called "standing" or "horn" hangers and are made of tubular metal. They are notable for the fact that they are convenient for hanging not only outerwear, but also hats, bags and umbrellas. And although they are not as stable as hangers nailed to the wall, they are more compact and mobile. They can be rearranged to any place or stored in the pantry for the summer.

In houses and apartments, this type of hanger is used less often than in public places, but it is also easy to make yourself. There are a few good ideas for example use:

  • cross for Christmas trees as a base and a long handle of a shovel as a stand, where ready-made long hooks are nailed;
  • trimmings plastic pipes and couplings for the base of the hanger;
  • process the base of a dried garden tree in the form of a multi-armed structure and install it on a cross or other base;
  • cutting pipes of different sections as a telescopic stand;
  • the remains of old chairs and stools and build a hanger on a rotating rotary mechanism(buy ready-made);
  • as a basis - a tripod from an old camera, a floor lamp and other household items.

Attention: Whatever the design, it is important to observe the main condition - the stability of the floor hanger. And this depends not only on its design, but also on its support. It can be a rotating disk, 3-6 legs or a cross.

DIY coat hanger or trempel

It’s not difficult to make a clothes hanger yourself, using any available material as a base:

  • thick wire;
  • a fragment of a thick branch in the shape of a hanger;
  • small plastic bottles, strung on a metal base in the form of a large “clip”;
  • bent metal plate or corner.

The base for the “hanger” hanger remains to be wrapped in padding polyester (another filling) and covered with any beautiful fabric. This best option for knitwear. A beautiful satin bow or a face from a small soft toy will help add originality. Children will love these hangers. The main thing is to find suitable metal for hook hangers.

Original do-it-yourself hangers from scrap materials

Interesting ideas for making hangers of any type yourself can be implemented using a variety of available materials.

1. Metal. Scraps of steel wire, tube or angle are suitable for a metal clothes hanger. Depending on the flexibility and thickness of the metal, the structure can be bent or joined by welding. The shape and design of the product is your choice, see photo:

2. Remains of timber, boards, veneer and other wood are suitable for a wall hanger or a universal product in the hallway. Detailed video useful for those who love woodworking;

3. Parts old furniture It’s also easy to transform it into a hanger, for example, by building a multifunctional model based on a chair. This design is convenient because a jacket and suit trousers, a shirt and a tie are conveniently located on one module.

4. The original base for hangers will become original device in a room where there is temporarily no wardrobe. Any wooden stalk that is suspended from the ceiling parallel to the floor at a level slightly above height will do.

5. The old “hunting” idea is to use deer horns instead of hooks for hangers. They can be attached to any base - for a wall hanger or vertical stand with horns. Moose antlers will also work.

6. The design made of plastic pipes will appeal to fans of technical crafts.

7. Small hangers for the closet are also needed, for example, in the form of connected rings made of cardboard or plastic. They are suitable for hanging scarves and neckerchiefs, belts and belts.

8. A simple roll-up wire hanger with clothespins along the edges is an excellent device for storing trousers or skirts. The shape of such simple hangers can be classic, in the form of a curved paper clip or in the form of an intricate labyrinth - as your imagination suggests.

Hangers as a stylistic decoration

When choosing the material, shape and design of hangers, you should consider the style of your interior:

  • a wooden hanger with chiseled decorations is suitable for an English office or a discreet classic hallway;
  • soft hangers covered with bright fabric will decorate a bedroom in country, shabby chic, romanticism or boho style;
  • metal-plastic structures will emphasize the originality of loft apartments and decorate the shelter of a lonely wanderer in the power of techno or hi-tech;
  • old restored hangers fit vintage, retro, Biedermeier or Victorian styles;
  • hangers of the simplest shape and design - an ascetic attribute in the style of minimalism or functionalism;
  • original hangers with a “girlish” design are suitable for a Barbie-style children’s room;
  • a chic and impressively decorated hanger - for a boudoir in a palace style;
  • satin ribbons, sparkles, beads and stones are the attributes of a glamorous bedroom.

Read more about self-production hangers watch video:

A DIY clothes hanger is a fruitful idea. Theater begins with a hanger; house too. In the sense of spirit, atmosphere, “energy”. The reason is simple: the first thing a guest looks for is where to hang his outerwear. And if the hanger is clearly homemade, but comfortable, stable and durable, the owner is guaranteed a positive reputation.

The second argument for making a hanger with your own hands is prosaic: purchase prices are clearly disproportionate to production costs. A homemade clothes hanger will allow you to save an amount that is quite visible in your budget. It’s not difficult to make, you only need a little material, and waste from repairs will also be used. In most cases, the tool can be used manually.

These factors are especially felt if a floor hanger fits in the hallway. In addition, it can also serve as a dryer if its design is framed, see below, because On such hangers it is convenient to hang clothes on hangers, and the hanger itself moves away from the wall. If you managed to fence off a dressing room in your house, then a floor hanger is the best option. The cost of floor hangers is significantly higher than wall hangers, but there is nothing in the design that would prevent you from making a floor hanger yourself.

On the floor or on the wall?

What has been said is already enough to make a choice, as long as there is enough floor space. However, let’s finally look at what makes a floor-type hallway hanger so attractive:

  • Clothes hung on hangers dry faster and do not stretch; The collar and lining do not tear.
  • On a hanger approx. wide. 1.5 m will fit a seasonal set of clothes for the whole family, which will save on closet space and space for it.
  • A shoe rack is naturally attached to the floor hanger, which simplifies the work of equipping the hallway and saves its space.
  • With the correct dimensions of the hanger, neither the wall from clothes nor the clothes against the wall are damaged.
  • The mobility of the hanger does not interfere with rearranging furniture; After moving the hanger, there is no need to seal the mounting holes in the wall.

However, there are different floor hangers, and not all of them are most suitable for residential premises. For example, for order (from the old Russian “order” - office, office, office) floor lamp hangers, pos. 1-4 in Fig., hanging clothes on hangers is inconvenient. Due to the small support area, they are rolly, especially when loaded with wet winter clothes. To emphasize the functional inferiority of the product, such hangers are called hangers, and they are often sold under this name.

Types of floor hangers

The best option is the same theatrical wardrobe frame hanger, pos. 5. When designed for residential premises, it is supplemented with shelves for hats, shoes and gloves/scarves; possibly with an additional tie rod, pos. 6. Disadvantage – the “legs” of the hanger get tangled under your feet. In an attempt to get rid of it, they came up with hangers - frames on a stand, pos. 7, but generally speaking, they are even more rolls than ordered hangers. Another option is a frame hanger without legs, leaning against the wall; We will remember this one again. There are also folding frame hangers, but they have almost no advantages in everyday life.

If space is generally tight in the hallway, then a wall hanger is still more suitable. Simple wall hanger-sconce, pos. 1 in Fig., is as compact as possible, but no more convenient than an orderly one, except that it won’t fall to one side from the next jacket. Hanger-shelf, pos. 2, will not fall off if attached properly, and hats/caps from it too, but the wall and clothes rub against each other.

Types of wall hangers

Wall hanger-panel, pos. 3, saves the wall, but not clothes. Leather items wear out the most on such hangers. Tanners jokingly advise: how can you tell a sheepskin coat made from full-grain leather from one made from reverse leather? The first one, with everyday use of the panel hanger, loses its appearance in 2 winters, and the second - in half a winter. Considering the cost of genuine leather products, this is no good. Therefore, wall hangers for expensive items often provide soft upholstery, pos. 4. As for wall hangers with openwork panels, pos. 5 then in in this case its meaning is only decorative: it does not protect either things or walls.

Floor hangers with chest and banquette

There are also floor hangers-panels with a stand, for example. in the form of a cabinet, chest or chest, pos. 1 in Fig. on right. This is not the best option: someone will someday put something on the lid, and the clothes being removed from the hanger will knock it onto the floor. Much more practical are floor hangers-panels with a bench, pos. 2. A flower under the seat is a matter of taste for the owners, if only it survives there, but a shoe rack or a chest for accessories for its care is in the drawer of the banquette.

Clothes and keys

Regarding panel hangers, the amateur craftsman has additional opportunity, namely: provide such a side panel on the edge farthest from the front door. Perhaps not reaching the bottom, with a bevel or notch. Factory ones don’t do this: the hanger should be designed for clothes to stick out from the side. One sidewall almost does not interfere with this, but it is unknown how the hanger will sit with the buyer, and making right and left hangers is expensive.

What does this add-on provide? A place for a key holder, invisible from the threshold. There, on the side, there may be a dressing table or a cabinet, but the main thing is that the owner’s keys will not catch the eye of a casual visitor, and they are in plain sight, as criminologists say, a serious factor in spontaneous illegal actions, without which, i.e. temptation, a visit from a not entirely trustworthy subject would have turned out well for both the hosts and him. You can, of course, make a luxuriously designed key holder with a secret lock, but this is a lot of work and costs for materials. Otherwise, a simple board with hooks will do. Or just hooks screwed to the side of the outside of the storage section.

Let's assume that a suitable design has already been chosen, and let's move on to how to make a hanger. Preferably wooden: the material is noble, natural, easy to process. Let's not forget other versions; in some cases more convenient. Let's start with floor hangers as the most functional.

Floor

Those who love to craft from the heart and have a wood milling tool at their disposal can immediately take up a floor-mounted frame hanger with legs. Made from fine-grained hardwood (oak, beech, hornbeam, walnut, birch), it looks luxurious and takes up only 360 mm of floor space.

A suit hanger works well as a prototype, you just need to make it taller and move the trouser bar up so you can hang hangers on it. Instead of a tie rod and handles, you can install a shelf, and a shoe rack is mounted below. Drawings of such a hanger are shown in Fig.:

Drawings of a wooden floor hanger

With the other dimensions indicated, the structural and overall width (sizes 430 and 460 respectively) without compromising strength and stability can be increased by 1-1.4 m, i.e. the hanger will be narrower than family width up to more than 1.8 m. Self-orienting wheels, if full mobility is needed, can be installed without problems.

About hooks and traps

Bags, umbrellas, scarves are also left on the hanger, and a bachelor’s skirt and lingerie may also be there. Sometimes life is life. It is also more convenient to hang clothes on hooks for a short time. Therefore, in frame hangers, sometimes slider hooks are put on the main rod (formerly the trouser rod in Fig; height 1360). They or the hangers, depending on the need, are moved to the side en masse. But the hook-sliders under the fingers turn out to the very inopportune moment. In a hanger of this design and similar ones, the problem is solved simply: the main rod is for hangers, and the fixed hooks are attached to the top board.

Pipes and profiles

Original hangers are made from round or profile metal or plastic pipes, see fig. However, despite all the design tricks, their organic defects do not disappear. The same ones that hanged the orderly. But it adds high labor intensity: in order to hide the connecting nodes, you have to really strain both your hands and your head.

Pipe hangers

It is better to make a square base for a floor lamp hanger from pipes. With the same floor area removed, the distance between the support points increases by 1.4 times. If you make the base even heavier, a hanger up to 1.7 m high turns into a full-fledged hanger. 60 mm sewer pipes are most suitable.

A short master class in pictures on making the base of a floor hanger from pipes is shown in the following. rice. Pipe sections are 150-300 mm, depending on how much floor can be given to the hanger. In addition to them, you will need 3 straight tees, 4 right angles and 4 plugs. Connections are made using propylene or PVC glue, depending on the pipe material. Weighting - sand or small crushed stone.

Making the base of a hanger from pipes

One of the comments to original design begins with a question something like this: “Why couldn’t you just solder it?” Judging by the fact that later in the same comment the 90° angles are called bends with an obvious claim to professionalism (plumbing bends are oblique tees), 2-3 more and the same number of exclamation marks suggest themselves in addition to the question mark.

Nevertheless, the author of the product, even if she did not know plumbing terminology, solved the problem quite like an engineer. The hanger doesn't need sealed joints, and a tube of glue will cost much less than renting a soldering iron for propylene. Which you also need to learn how to use, spoiling a lot of the material. For greater reliability, you can reinforce the connections with phosphated (black) self-tapping screws: their heads are not visible on black, and the strength of the hanger will not be reduced.

Note: the top in the original design is also made of pipes, but its design, frankly speaking, is not that... It would be better to drill inclined holes in the rack and insert some strong pins into them using the same glue; wooden, metal.

Simple frame

Scheme of a simple floor-wall hanger made of pipes

A frame hanger made of pipes can be without legs, simply leaning against the wall at an angle. However, its slope must be negative. There should be at least 350 mm between the wall and clothes on hangers. If the frame tilt is positive ( top bar adjacent to the wall), then the lower one will “move away” from the baseboard by 500-600 mm. In a small hallway this is a serious inconvenience. In addition, they will either cling to the bottom crossbar with their feet and it will break the floor, or they will have to fasten it to the floor, and this is really bad: any violation of the flooring is fraught with complex and expensive emergency repairs. Have you ever seen furniture on sale that needs to be screwed to the floor? Except that special purpose, eg. rack. And then, they also try to make do with fastenings to the walls and, in extreme cases, the ceiling.

The diagram of a frame hanger with a negative slope made of pipes is shown in Fig. The materials are the same: straight segments sewer pipes 60 mm, 90 angles and straight tees. The usable floor area taken away is zero. Below there can be a shoe rack or a banquette. For fastening to the wall, so as not to drill a lot and do without expensive collet anchors, it is better to take a couple more tees: with their help, the holding beams - guy wires - are attached to the wall with a pair of self-tapping screws in dowels each.

Wall mounted

Simple panel hangers do not require any special disassembly. How to make a wooden wall hanger, see e.g. video.

Video: DIY wall hanger made of wood

Here we remember, firstly, about the sconce hanger. Folding, it can be very useful if a large company has gathered or the kids have returned from the yard.

An example of this kind of design is shown on the right in Fig. However, its creators were clearly guided by the principle: “Consumption is the basis of cash circulation.” The outer (folded) side of the flap is inactive and requires a locking mechanism. And a separate hanger for every day.

Compact folding wall hanger

Meanwhile, folding wall hangers have been known since Ancient Egypt. In the climate there, outerwear was worn occasionally, in bad weather, but after wearing it it was necessary to dry it. There was no point in keeping a separate hanger for this in areas where it rains and is cold not once a year, so they came up with one like the one on the right in Fig.

When folded, the compact Egyptian wall hanger was secured with a cypress stick. Now, of course, you can install a ball retainer or just a hook. The main thing is that the hook hooks should be 3/4 of a circle, then nothing will fall off them even with the bar folded back. And without need, the whole hanger looks like just a stick on the wall; You can hang bags, umbrellas, and keys on the hooks.

More about hooks

An original wooden hanger can be made without any metal at all, not counting the fasteners. Do not rush to throw away the New Year's pine or Christmas tree (only the blanks will need to be turned upside down):

Video: original DIY wooden hanger


Such a hanger will look best in a country house, in a timber or frame house. Depending on the interior design – even in a city apartment. It will go well in the bathhouse: touching steamed skin to metal is both unpleasant and, to some extent, even dangerous.

Hangers for the nursery

Probably all children throw away their clothes. There is no need to particularly scold them for this: without experiencing chaos within reasonable limits, you will not get accustomed to order. Who is against it - answer Friday’s question to Robinson Crusoe: “Why doesn’t the devil kill God?”

However, it is necessary to teach children to handle things properly. Only a children's hanger, so as not to cause obvious psychological rejection, should look somewhat disordered. It is also highly desirable that the child associate it with his favorite game or hobby. Examples of “game/hobby” type wall hangers for children’s rooms are given in pos. 1 and 2 fig.

Children's hangers

A universal method of this kind is a tree hanger, pos. 3. In the contour of a tree, as in any fractal structure, order and chaos interact and complement each other, giving rise to a harmonious whole. Just don’t forget to make the wood stronger, e.g. from plywood from 12 mm, and properly, in increments of no more than 250-300 mm, attach to the wall with self-tapping screws from 6 mm in propylene dowels. A tree is meant for climbing.

Floor hangers in a nursery are undesirable for the same reason: well, they will climb anyway and crash. Therefore, if you want a floor hanger for the nursery, you need to make one that you can’t fit on, as can be seen in pos. 4 and 5.

About cutting plywood

In any case, parents are faced with problems that little ones don’t care about yet: material consumption and labor intensity. Drawing a complex contour along a grid on a single sheet of plywood is no longer easy; then you need to cut it out precisely, which is even more difficult. And in the end it turns out that 60% or 80% of the material went to waste, no longer suitable for anything. On the contrary, you need to make a children's tree hanger from waste. Or cut a whole sheet more tightly.

Assembling parts of a wooden hanger from plywood

The method for this has long been known: element-by-element cutting and assembly. If the tree is plywood, for complete strength of the finished product, each part is assembled from 2 layers, leaving the corresponding folds and grooves, see fig. Fragments of blanks are assembled using PVA glue, wood glue or “Express” (liquid nails). If the assembly is made of PVA, the fragments must be additionally fastened with small snake nails in increments of 100-150 mm with a distance of 30-40 mm from the edges.

The wooden hanger is assembled using the same adhesives, but now each connection must be secured with wood screws and an envelope. Then the gaps and fastener heads (they need to be recessed during assembly) are rubbed with putty made from sawdust of the same plywood on PVA. Such wood will look solid even without painting, only under varnish.

Note: Just in case, let's remind you - that's it wooden parts any wooden hanger Before assembly, you need to sand it with fine sandpaper and treat it with a water-polymer emulsion or PVA diluted three to five times with water. After impregnation before further work take a technological break until the part is completely dry (1-3 days, depending on its size).

And one last thing about hooks

In the illustrations above, you most likely noticed the curved wooden hooks and other details of the hangers. It is quite possible to make them at home. In production, dense, fine-grained, defect-free wood or waterproof birch plywood (BS grade) is bent by heating with steaming or dry, but for homework these methods are too complicated. Only bamboo is steamed more or less simply: the workpiece is boiled for half an hour or an hour in rapidly boiling water, after which it is bent by hand. In the case of bending according to a template, the workpiece must be quickly tied to it, before it has cooled down, with a wide cotton braid or a strip of natural tarpaulin.

Wood rasp

At home, it is easier to cut blanks of the required configuration from a sheet of plywood (any) or MDF of the required thickness or, twice or four times as much in quantity, from thin sheet material to then gain as much thickness as required. Cut with a finishing allowance of approx. 1 mm. The cut blanks are tightly pulled together in a package in a carpenter's vice or in a mechanic's vice through spacers made of thick plywood and processed with a wood rasp to size, and then sanded clean. One rasp is enough, with flat and semicircular working surfaces, see fig.

The blanks are assembled into parts using the method described above. The end surfaces, if it is necessary to hide the layered structure of the plywood, are sealed with strips of self-adhesive wood-like film. After this, the part is varnished twice or thrice. acrylic varnish water based; nitro varnish can damage the self-adhesive. Edge (edge) plastic furniture edge it’s not worth it: you need to accurately select the groove for the edge anchor, which requires a milling machine, but on curved surfaces of great curvature and short length the edge still does not hold well. And parts covered with self-adhesive tape, varnished, and solid wood cannot be immediately distinguished even by a master cabinetmaker.

(Visited 21,674 times, 1 visits today)

Sections