Do-it-yourself woodshed: the optimal design for storing logs. How to make a woodshed from metal with your own hands? Small attractive firewood boxes
Building a woodshed with your own hands is not difficult. The structure is useful and necessary and can look different.
To store firewood for a stove, fireplace, barbecue, bathhouse, etc., you need appropriate place. Moreover, firewood must be stored in accordance with certain rules. Of course, you can use a regular shed or allocate a place for firewood in the utility block (in this case there should be natural ventilation), but you can also set up a woodshed yourself.
As for the concept itself, in some Russian regions a woodcutter is also called a drovnik. The name drovnitsa is often used. But there are some differences between them. A wood shed is an ordinary shed that stands on a foundation separate from the house and has a door. The woodcutter is a more simplified version. It is a shed for firewood. In the old days, the same concept was used to describe people who carried firewood around the yards and traded it. A firewood rack is understood as a stand for the firewood that will be consumed in the near future.
Preparatory work
So, how to build a woodshed with your own hands with optimal expenditure of money and time?
First you need to choose a place where the woodshed will be located on the site. Only need to consider rational options. The design should not be too remarkable and immediately catch the eye. It should not be located too far from the house, so that you do not have to carry firewood over long distances. It is necessary to install it so that the car with firewood can get as close to it as possible, otherwise you will have to carry it yourself. If there is no stove heating or a fireplace, it is best to place a wood burner near the bathhouse or place where barbecue and barbecue are usually made. It is recommended to draw a diagram of the yard and select a location for the woodshed, taking all these factors into account. The structure may be located near the wall of the house or outbuilding or it can be free-standing.
Before you make a woodshed, you need to think about its type. First you need to figure out the budget. This will curb fantasies. Most cheap option- this is a tree. If desired, the structure can be sheathed along the frame with boards.
It is necessary to make a firewood shed for the dacha so that the new building looks organically on the site. It is best to build it near the main building. In this case, there will be less work and you won’t have to think through the design.
In any case, the structure should be located in a dry place. Best to choose shadow side. In order for firewood to dry properly, it needs ventilation. But direct rays of the sun are prohibited. If the woodshed is located near a building, then it is best to choose its northern side.
For wall cladding, you can use slate, corrugated sheeting and polycarbonate. If these materials are chosen for wall cladding, then it is necessary to make gaps so that there is natural ventilation in the woodshed. If you carefully paint the structure or cover it with colored polyurethane varnish (this only applies to the processing of wooden elements), then the new building will look more elegant. You can plant several trees and shrubs nearby. Thanks to this, the place will look more comfortable and beautiful. If the walls of the woodshed are made of tree cuts, and grass grows on the roof, then such a building will resemble a hobbit’s house.
What to consider?
When the appearance of the future woodshed is fully thought out, it is necessary to prepare its drawing, select materials and tools. As for the construction scheme, a more detailed option will be needed if it is planned to store not only firewood in this room, but also other necessary items (for example, various instruments). In this case, the woodshed will already be combined with the barn.
The drawing also helps to figure out the area of the room, since the supply of firewood in each family is different. According to calculations, to heat a house of 100 sq.m. in autumn and winter approximately 2.1 cubic meters are required. m. of dry firewood per month. This only applies to pine trees. If you use birch trees, you will need approximately 1.7 cubic meters. Dry firewood refers to those whose moisture content is no more than 20%. This is achieved after a year of storage in the woodshed. But you will need much more fresh firewood, since their heat transfer is 2 times worse. In addition, a reserve must be made for at least a couple of seasons. Of course, each furnace has its own productivity, coefficient useful action. Eg, modern models have a very high rate - more than 80%. One load of fuel in them will be enough for 10 hours of warm-up. But such calculations are only suitable for conventional ovens. It is also necessary to take into account fuel for the bathhouse and barbecue.
As for the tools, you need to prepare a drill in advance if you plan to install a woodshed with 4 pillars that are dug into the ground. This is traditional rustic option. In addition, you will need a hammer, a hacksaw, a plumb bob, a stepladder, pliers and twine. As for the materials, they are chosen so that they suit the interior of the yard. The simplest structure can be put up from leftover materials after the construction of other buildings or after dismantling old structures.
Stationary woodshed
It’s actually not difficult to build a stationary firewood shed for your dacha with your own hands. This option is called stationary, since the structure is installed on a columnar foundation. This structure is not considered capital. The woodshed will be reliable, strong and durable if pits are dug under its pillars to the depth of the soil freezing level. Also, such pillars must be filled with concrete. You can only get by by filling the hole with gravel and sand (but each layer must be compacted).
It is not worth placing pillars directly on the ground, as the structure will be shaky, especially in spring time when the soil begins to swell. If the structure is planned to be small, then it will be enough to make 4 pillars. If you plan to make a more spacious room or equip a utility block that is combined with a woodshed, then you will need more poles.
Next we install the frame. A timber size of 15x15 cm is used. All wooden structural elements must be treated with impregnation with fire-retardant properties beforehand. Don't forget about waterproofing. To do this, it will be enough to fold the roofing material into 2 layers.
Now you need to install the vertical frame using the corners. First, you should install the racks that are located at the rear, then those in the middle, and finally the front ones. It is necessary to tie everything at the top and nail the rafters to the roof. It is best to make your work easier by fixing the beams on the vertical frame with temporary braces.
Next, you need to sheathe the horizontal frame with flooring boards. There is no need to precisely adjust the boards. On the contrary, there should be gaps to allow natural ventilation in the room. But at the same time, the gaps should not be too wide, so as not to damage your limbs. Water and debris will flow into small cracks. In addition, it also provides additional bottom ventilation.
It is recommended to make the roof from single-pitch corrugated sheeting. Depending on your preferences, you can choose gable material. Concerning roofing material, then anyone will do, but you need to rely on your budget. It is recommended to make a canopy near the entrance to the building to prevent water from getting onto the logs. To make a visor, you can use an end-type board. This option is the cheapest and simplest, but you can use others depending on the taste and wishes of the residents.
Now, if necessary, you need to cover the walls with boards. The boards are supposed to be nailed down, making small gaps. This will provide the necessary ventilation in the room. All wooden elements must be treated with antiseptic and fire-fighting means. After this, apply paint or polyurethane type varnish. This way the design will not only become more beautiful, but will also last longer.
Wall-mounted and portable option
If you need to build a wall-mounted woodshed in your country house, then you need to choose the north side of the house or other building. Firewood should not be left in the sun. To ensure proper drying, high-quality natural ventilation is used. During the construction of such a firewood shed, it is necessary to take into account that water can flow from the walls of the main building directly onto the firewood itself. This cannot be allowed. It is necessary to move the firewood shed slightly away from the wall of the main building or install a roof of a suitable shape.
As for the rest, the wall-mounted shed for firewood repeats all the steps for building a firewood shed separately standing type and is practically no different in installation work. A wall-mounted shed for firewood has the following feature: the structure extends slightly behind the house or other main building. This option seems very simple, but if you show your imagination, you can make the structure interesting.
There's more you can do portable canopy for firewood There are many ready-made varieties of these portable structures, which can be purchased at a specialty store. You can also order various forged models in workshops. They look very nice. Or you can build structures yourself to suit your taste. A forged metal woodshed cannot be made at home, but you can show your imagination and make a canopy using available materials. Everyone can realize their dreams. The main thing is to think through all the nuances.
For example, an old barrel can be used as a basis for creating an unusual firewood burner. First, you need to mark everything on its body. The hoop must be moved with a hammer to the central part, where it will be needed later. Then fix it in this position using self-tapping screws. You can choose beautiful bolts. Then you need to cut out the selected shape using the markings. The cutting areas must be treated with plaster. You also need to use a jigsaw to cut out the shaped legs from the board. Insert the sanded old cutting into the holes that were drilled and secure it. Metal elements paint. Wooden parts treat with colored polyurethane varnish or stain. Such a log burner will look beautiful near the fireplace.
Each economic owner of a summer house with a bathhouse, barbecue or stove will certainly have a designated place for storing firewood. The woodshed can be shaped like a barn, a gazebo or a simple shed on supports. However, there are also very creative options.
It’s not difficult to build a woodshed in your country house with your own hands. But before work, it is important to decide on the type of design, select suitable materials for construction, as well as read step-by-step instructions.
The purpose of this design is clear even from the name. Under the woodshed's canopy, logs are neatly stacked in stacks for further storage. However, along with its direct purpose, such a building can become wonderful decoration summer cottage plot.
Do-it-yourself woodshed construction technologies
The dimensions and design of the woodshed are selected based on the expected amount of firewood that will be constantly stored. It would be appropriate to develop a project taking into account modern materials and technology.
The optimal moisture content of firewood for fuel is at the upper limit of air dryness, i.e. 15-20%.
If it is planned to build a woodshed around, or around frame barn, then it is rational to build a closed structure, more reminiscent of a barn (with or without a porch).
It is better to build such a structure using frame or frame-panel technologies, guided by considerations of speed of work and low cost of materials. Also, the woodshed can be combined with outdoor toilet
or a barn, have two separate entrances and a common wall.
How to make it in the form of a gazebo In this case, the structure has a floor covering, two or three sheathed walls, and some kind of canopy (for example, made of profiled steel sheets or polycarbonate). Rafter system
such structures are not always equipped.
A woodshed of this design can be attached to a house, bathhouse, outbuilding or other building, but it is better not to resort to such a measure in order to avoid the appearance of bark beetles and damage to the firewood and walls of the building.
In the form of a canopy The most simple design
. The canopy is attached to several vertical support posts and protects the logs from rain.
The firewood is well ventilated and dries, but in winter it will probably be covered with snow, and in the worst case, ill-wishers will easily take away all the supplies from under such a canopy.
Modern firewood racks of non-standard shapes For example, a woodshed can be built using panel technology and look like a honeycomb. Firewood is stored in separate cells. This allows you to sort the firewood, separating dried from wet or larger from smaller. Firewood racks in the form of racks are no less convenient. However large quantity
There won't be any firewood in them. Another one interesting idea– use of old barrels or cuts of very large trunks for storing firewood . The core of the saw cuts is removed, the elements are placed on top of each other and secured with wire/rope. Advantage: original design
. Disadvantage: low structural strength. The smallest firewood sheds for the dacha are metal, wicker, glass, and plastic. and woodburners produce using cold or hot forging
. The woodshed has the shape of a small basket, floor rack, etc. Small firewood burners are used exclusively indoors, for example, installed near fireplaces or sauna stoves.
Selection of materials for building a woodshed
Tree Wood is perhaps the most popular material
for the construction of a woodshed and. The building materials used are timber, edged and unedged boards, pallets, fiber boards, plywood, logs, etc.
Wood is easy to process, installation takes a minimum of time, the buildings look quite aesthetically pleasing and harmonize with the landscape of the dacha.
You can build a woodshed out of blocks and bricks; such a structure will be quite strong and durable, but the design requires significant investment and labor.
If the woodshed is built in the form of a shed, high-quality ventilation is required, otherwise the firewood will not dry and will begin to rot.
Metal profile and polycarbonate
Metal structures are very durable, and artistic forging elements turn the firewood rack into a masterpiece. Metal constructions require protection against corrosion. Polycarbonate is usually used in conjunction with metal or wooden frames. You can use this material to make a roof, make a canopy, sew up the wall of the woodshed. The advantages of the material are availability, easy installation, high light transmittance.
Calculation of approximate costs
Materials:
- board 5×15cm for pillars – 3-6 thousand rubles. /m3;
- board 5x10cm for the floor, walls, roof rafters;
- 15 mm plywood for the roof - from 500 to 1200 rubles / sheet;
- board 2.5x5cm for finishing;
- hot-rolled equal-flange metal corner - about 40-80 rubles / linear meter;
- self-tapping screws - from 0.09 rub./piece;
- nails – up to 100 rubles/kg;
- fastening corner - about 30-40 rub./piece;
- ondulin - 450 rub./sheet, galvanized profiled steel sheet - from 185 rub./m 2.
How to build step by step
The video shows the process of constructing a classic woodshed:
Designing a wood shed
Let's consider step by step instructions construction of a country woodshed in the form of a gazebo with sheathed walls, pitched roof and without entrance doors.
The frame will be made of lumber, the wall cladding will be plywood, and there will be a small one above the entrance. The dimensions of the structure are 2.5 x 1.4 m.
Laying the foundation
The woodshed is a lightweight structure that can be supported by a foundation made of horizontally aligned blocks. If desired, you can pour a shallow shallow base or lay out a prefabricated strip foundation from blocks, as is done during the construction. IN winter time It is more convenient to equip a pile-screw foundation.
Sometimes a foundation is built from car tires. This is an unusual, but quite budget option.
Any type of foundation must be waterproofed with roofing felt / bitumen mastic.
Bottom trim and floor laying
For the lower frame, which is traditionally laid on the foundation and fastened to it with anchors, you can use high-quality boards or timber. If timber is used, then its opposite edges should be cut down according to the “half-tree” pattern for a reliable connection. Read about building a shed from 6x3 timber with a terrace.
The floor joists are attached between the boards of the bottom trim. For a base of the size indicated above, you will need 7 boards 120 cm long and 28 mounting angles. Fixation is done with galvanized self-tapping screws. For convenience, it is better to use a screwdriver.
Floor covering in progress edged board. It is advisable to leave a gap of up to 25 mm between the flooring boards to prevent moisture accumulation and better ventilation of the floor and firewood. The boards are laid across the joists and secured with nails or self-tapping screws. About frame houses find out with an attic.
All wooden elements must be treated with an impregnation that improves fire safety and prevents wood from rotting (for example, Senezh impregnation).
Installation of frame posts
Before installing the support posts, 5 x 10 cm boards are laid and fixed around the perimeter of the structure. The posts will be attached to them. Each rack is made of two boards, which are held together with wood glue and nails. Instead of boards, you can use 10 x 10 cm timber.
For a firewood rack with a perimeter of 250 x 140 cm you will need:
- 6 racks 140 cm long;
- 2 racks 155 cm long;
- 2 racks 171 cm long.
The racks are installed vertically and fixed with mounting angles. For greater reliability corner posts reinforced with jibs. The shortest racks are the back wall of the woodshed, the longest racks are the façade. Verticality is checked with a bubble level or plumb line. How to do country toilet without cesspool find out by .
The front wall (also known as the entrance opening) will be formed from three boards - two vertical, 171 cm long, and one horizontal. The length of the crossbar must correspond to the width of the entrance opening. It is best to attach the crossbar (with perforated corners) at a height of one and a half meters from the floor line.
Roof installation
To arrange the roof you will need boards that will serve as rafters. These elements are laid at an angle of 15 degrees. The rafters are attached to the top frame, which consists of beams or boards attached to the upper points of the support posts. The upper ends of the supports are cut at an angle of 15 degrees, sloped to the side back wall woodcutter You will need 6 rafters. They are attached to the top trim with nails. Read how to make a carport at your dacha.
The boards are not laid flat, but on edge.
Wood shed wall cladding
The walls of the woodshed can be covered with slabs crossed with slats (like a lattice), moisture-resistant plywood, etc. If it is attached and use similar materials. Cuttings of tree trunks are perfect for decoration.
The casing is fixed to support posts galvanized self-tapping screws.
Canopy or canopy
The canopy is installed before the finishing roofing material is laid. This structural element will additionally protect the woodshed from precipitation. For the canopy, you should take 6 pieces of boards of the same length, cut the ends at an angle of 15 degrees and attach the parts to the top trim or lining of the woodshed.
To strengthen the structure, supports are placed under the rafters of the canopy. The ends of the canopy rafters are sewn up with an end board. A sheathing is mounted on top - the basis for roofing visor It is advisable to sew up the junction of the canopy and the roof with a metal strip or ridge profile.
Maintenance of the woodshed at the dacha
Built by frame technology an open woodshed does not require any special care; only the wooden elements can be additionally varnished. It is better to equip the area before construction by laying paving slabs or pouring concrete.
Lantern powered by solar panels, will decorate the façade of the woodshed and will allow you to take/stack firewood in the light in the evening.
Let's start with the foundation. The foundation for the woodshed will be concrete foundation blocks. Small holes were dug under them, sand was poured in (to level them) and the blocks themselves were installed. It turned out like this:
He laid a layer of roofing felt on the foundation and began laying out the bottom frame of the woodshed:
I used 100×100 mm timber. Fastening using metal corners and self-tapping screws. This is how the frame of the woodshed turned out:
The roof of the woodshed is pitched. First I installed the rafters (with a 330mm overhang):
Then I laid corrugated sheets on the roof:
The floor was covered with a 40mm board, leaving a gap between the boards of approximately 25-30mm.
It's time to sheathe the woodshed. The board is 100mm wide, leaving a gap of the same width between the boards:
Finally, I painted the walls and floor with an antiseptic (Biotex Rosewood). Here's what we ended up with:
And here is a photo of a woodshed filled with firewood (5 cubic meters):
The inside is quite spacious, you can easily reach any corner. If you fill it to capacity, I think it will fit 8 cubes. Let me remind you, the dimensions of the barn are 2 by 4 meters. The internal dimensions turned out to be 1.8 by 3.8 m. Height: 2.2 m (at the far wall), 2.45 m (at the entrance).
It took 3 days to build the woodshed myself. 10 thousand rubles were spent on materials.
A firewood shed is a structure designed to store neatly stacked firewood, which you cannot do without outside the city. It allows you to store fuel so as not to take up much space and allow it to dry. It’s more convenient to create it yourself in order to guess the size and shape as much as possible, and also get a product that meets the individual needs of the owners.
Features of a homemade firewood rack
A homemade woodpile for firewood is formed in accordance with several mandatory conditions. Firewood must be protected from rain and snow, but still have the opportunity for ventilation. In addition, it is important that the chosen location is in the shade, away from open fire. Materials should not be stored directly on the ground; the floor should be made of either bricks or planks.
However, it is very bad if the floor connects directly to the ground, so it is important to maintain a gap.
The next condition is the attractive appearance of the structure., which should be combined with the rest of the buildings on the site and the general landscape design. It is important that the building is convenient for use: the owner has the opportunity to approach it from the required side and easily obtain the required amount of firewood. In this case, the fuel material must adhere tightly and not fall apart.
Suitable location
It is important to say that some people at their dacha do not make a special woodpile, but simply store firewood in the open air, covering it with material that protects it from water. But also for this purpose you can use an ordinary shed already existing on the site. Special street design located close to home will be much more convenient. By the way, if firewood is most often used for cooking on fresh air, then it is more logical to place the firewood closet to the stove or barbecue. The optimal location is the wall metal garage or a special area near the house. The main thing is that the firewood can be supported on three sides.
Exist beautiful designs, made of metal or wood, that are installed indoors. For example, this could be a vertical firewood rack for a room with a fireplace. In this case, the wood storage function is added decorative function. A portable mini firewood rack is often made by hand.
Usually it stores a supply of firewood for lighting the stove, which you have to replenish when you go outside.
Which material to choose?
From the right choice The material will largely depend on how long and how successfully the firewood box will serve. For the street, metal is often used, which makes it possible to produce a visually attractive structure that will serve for a long time and will not deteriorate from precipitation and other weather conditions. For example, it could be a woodpile from aluminum profiles, self-production which takes a couple of hours at most. By the way, it is very convenient to use for carrying, because its low weight greatly simplifies this procedure.
Reliable and durable products are made from iron or steel parts, for example, rods or pipes.
The most popular are woodpiles made from wood. If the aesthetic appeal of the issue is not too important, you can use existing materials left over from previous construction work, and do not purchase new ones. As an option, wooden structure can be made of pallets, pallets, beams, bars or boards. The only thing important condition– pre-treat the material with a product that protects against moisture and insects. A wooden firewood rack is quickly assembled, can be used for quite a long time, weighs little and is budget-friendly.
Covering a woodpile located outdoors is a must, and slate, sheets of metal, polycarbonate or even polyethylene are suitable for this purpose. By the way, the structure can even be woven from vines, if the latter grows in large quantities on the site. Separately, it is worth mentioning the woodpile built into the fireplace or stove, that is, it is a niche next to the firebox, made, as you might guess, of brick.
Decorative woodpiles, which are small in size and located in residential areas, can be forged, a regular bag made of thick cord or rope, a basket made of durable material, or even a regular one. wooden box with wheels.
How to do it yourself?
There are a large number of designs and drawings of various woodpiles on the Internet. They can vary in shape and appearance, have a frame or canopy, look like an ordinary barn with lattice walls, or be a real work of art. For a large amount of firewood used, a shed is more suitable, which can be regular or lattice. In the latter case, it will be possible to ensure better ventilation, which means the firewood will remain dry. In any case, you will first need to prepare the foundation - dig a pit for soft soil, the depth of which will vary from 20 to 25 centimeters.
The resulting hole is filled with layers of gravel and sand. Next, you can build a support of six blocks: a couple should be in the middle, and the rest should be in the corners. The parameters of the standard block are 200 by 200 and 600 millimeters. At the next stage we put double layer roofing felt
To assemble the frame, you will need to use bars with parameters of 100 by 100 millimeters, pre-treated with special machine oil.
The formation of the lower trim will be facilitated by the use of screws, nails or self-tapping screws, thanks to which the blocks and bars will be connected. The strapping is strengthened with special corners, after which you can begin installing the racks - respectively, in the corners and in the middle part. In addition, you can add a couple of racks in front and one rack behind. They will be responsible for entrance area and, accordingly, additional support. It is important to make the front pillars slightly longer and the rear pillars shorter to ensure a rainwater drainage system.
Boards are nailed to the side, after which the rafters and roof frame are formed. Roofing felt and corrugated sheets are placed on top. A roof overhang distance of 35 centimeters should be maintained. The floor can be laid so that gaps of 2 to 3 centimeters remain. It will be most convenient to assemble it from boards measuring 100 by 40 millimeters. The walls, by the way, are installed at intervals of 100 millimeters.
It is necessary to cover the shed with a special solution that will protect against beetles.
A small woodpile is most often located next to the home fireplace and is made of either wood or metal. In the first case, it is recommended to take as a basis old barrel and disassemble into separate planks. Since each piece is usually bolted to a metal hoop, it will have to be cut first. The bed can be easily made from chipboard or ordinary wide board , and the legs are made of wooden blocks. It is important to varnish the resulting firewood for better appearance
, as well as long-term use. A steel woodpile is also often made independently. It is assembled from a 2-mm steel sheet and a steel rod with a cross-section of 8 mm. The sheet is bent or cut out in a semicircle, which can be done with a grinder or gas cylinder
. Next, legs and handles are attached to the resulting container. For beauty, the firewood box should be painted with black or silver paint.
First of all, a rectangle is assembled from slats to form a frame. Then several holes are made on opposite elongated sides. A copper wire is inserted into the middle holes, transforming into handles, and a vine is inserted into the rest. Having intertwined all the twigs, you can fix the finished firewood using stain or varnish.
If you don’t have time to create a full-fledged structure, you can make a firewood stand with a support made of stakes. First of all, the surface is treated - covered with pebbles or covered with a special waterproofing material. The material should be taken rectangular so that the woodpile has four distinct corners. High supports are dug into these points, to create which ordinary logs are taken. Their thickness will depend on the amount of firewood that will be stored.
Woodshed - extension to the house
The benefit of a woodshed is that under a canopy the wood dries out and does not get wet due to snow and rain. Even raw wood Over the course of a season, under a canopy, it dries out and becomes suitable for use in a stove or fire.
The firewood storage should be built as a separate room, or as a shed extension to the wall of an existing building.
Woodshed near the wall of the house
Variant of the woodshed with a design of approx. external wall residential building under a canopy.
Woodshed in country house- option near the wall of the building You can pre-allocate a place near the wall, a niche for future firewood preparation. It is very convenient in terms of accessibility, the main thing is that the canopy completely protects the wood from precipitation.
Choosing a location for the woodshed
When choosing a place for a woodshed, take into account the distance to the furnace; it is best to place it near a utility block or shed. Or at the back wall of a residential building.
Woodshed next to the bathhouse The photo shows a version of the woodshed of the woodpile under the roof of the bathhouse. When storing firewood in this way, take into account the direction of the prevailing winds so that slanting rains do not flood the workpieces.
A small woodshed with your own hands near the house The woodshed can be small, in the form of a low canopy. This is good for a dacha, where you do not spend the whole winter, but only part of the time in the off-season. In this case, not much firewood will be required. If you come for a weekend in winter, you won’t need a lot of firewood.
Choosing the type of wood burner
DIY woodshed shed The woodshed canopy is the simplest and most convenient design. Allows you to fill the room without problems, the availability of firewood is excellent. It can be with three walls and a roof, the floor is at your discretion. Instead of gender, an option is possible wooden logs— guides on which firewood is placed. The canopy can be attached to an existing building, this will allow you to limit yourself to two walls.
DIY woodshed shed A woodshed in the form of a barn can also be built with your own hands in as soon as possible. It is recommended to make walls in steps for better ventilation internal space. The roof is usually gable or single-pitch, at your discretion.
How to make a wood shed with your own hands The woodshed can be combined with utility room, the photo shows the idea of this option. On the right is a woodshed, and on the left is a utility block for storing summer cottage equipment.
Materials for construction: do-it-yourself woodcutter
Wooden woodshed with your own hands Wood is usually used to build woodsheds, and it can even be used boards or substandard slabs. If your yard has a single design style, then the design of the woodshed, naturally, should correspond to the general style of the site. In any case, any room for storing firewood should have natural ventilation.
Beautiful woodshed - ideas for a summer house Some summer residents make their woodshed from polycarbonate. The idea, in my opinion, is interesting, the only thing you should pay attention to is that ventilation in such a structure should be on all sides, since plastic does not breathe and can retain moisture.
Wrought iron woodshed in the country A small forged woodshed will be an excellent addition to the recreation area, gazebo with barbecue.
Ready-made woodsheds - for home and garden
Metal woodshed for home and garden Now you can buy ready-made wood burners, absolutely different forms and sizes. from small firewood sheds to full-fledged woodsheds.
Construction of a woodshed adjacent to the wall with your own hands
The woodshed itself is a fairly easy structure to build; you can take any shed as a basis and turn it into a full-fledged woodshed, the main thing is to plan the ventilation in advance so that the wood dries naturally.
If you find it difficult to manage the shed, you can attach the woodshed to the wall of the house. If possible, choose the north side of the house - insulate the wall and dry the firewood. If this is not possible, then just look for a free wall and make a canopy.
How to build a woodshed with your own hands Can be used as a floor construction pallets— pallets. They should be placed on bricks, or a full-fledged floor should be made from boards. The frame can be made of timber, and the roof can be made of corrugated sheets or polycarbonate. I do not recommend working with roofing felt, as it quickly becomes unusable - in just a couple of seasons.
Do-it-yourself woodcutter near the wall of the house The frame of the woodshed should be covered with boards, with a small step for ventilation.
Construction of a woodshed - planking IN in this case The roof of the woodshed is made of flexible tiles. It turned out to be a very attractive option!
DIY woodshed shed - roof It’s a good idea, take note and make a similar wood burner with your own hands!
Construction of a separate woodshed
DIY woodcutter drawing A free-standing woodshed can be built on a columnar foundation, or simply on concrete blocks, even without deepening, just on a crushed stone cushion.
The principle of building a stationary woodshed - we form the bottom trim, logs, lay down the subfloor, raise the frame of the walls, make top harness and the roof. Then we cover the frame with boards or slabs, with slots for natural ventilation, cover the roof with roofing material.