Passwords for intercoms. How to hack a Metacom intercom and write a new key into its memory
Our universal key opens the following MODELS of intercoms:
Metakom MK-2003
Metakom MK-20TME4
Metakom M-10
Metakom MK-99.2-TM
CYFRAL CCD-2094.1
CYFRAL-intel
CYFRAL CCD-2094.1M
CYFRAL CCD-20 (approx. 70%-80%)
Cyfral 2094/tc (no more than 50%)
Factorial DM-20TM
Metakom MK99.2-TM
Raikmann PROEL KDC-1803
Vizit SM-100
VIZIT BVD-N100
Visit of BVD-341
Visit of BVD-431
Visit of BVD-311
Visit of BVD-313
Visit of BVD-342
Visit of BVD-M200
Metakom MK-2003-RF
and etc.
Video clip, clearly demonstrating universal keys In action
As you know, to set up an intercom you need to enter the programming mode, for which you need to enter the installer code, i.e. dial password. Having entered the programming mode, the master receives all rights to change the functions of the entire intercom.
Therefore, intercom manufacturers paid quite close attention to this part of intercom programming... But they implemented it in different ways...
Intercoms considered for apartment buildings, which have become widespread in Russia. We deliberately do not present here codes that are used not to open the door, but to configure them and which are needed by non-engineers only for hooligan reasons.
Information on hacking is provided for the following intercoms:
Barrier II and IIM, 4
VIZIT ( different models)
Cyfral (various models)
Eltis
METAKOM
Rainmann
DomoGuard
Blink
T-Guard
First of all, the question is: are there special intercom codes for opening doors by special services? Correct answer: no, modern intercoms do not have such codes (except for Barrier IIM). But there is forgetfulness of engineers who, as a rule, do not change master passwords during installation.
Hacking Barrier II and IIM intercoms
Remember those old “Soviet” intercoms with mechanical locks and a flat magnetic key? For 2M there is permanent opening code - 1013. But they were rare then, and even more so now. In general, these intercoms were opened with 2 magnets, for example from a disassembled key. You just move them around the key pad until they go off.
Barrier - 4
The same, only without buttons (single-user, designed for front doors with concierges). The key has 3 magnets.
VIZIT intercom codes
General note: If there are no * and # on the keyboard, use C and K instead. C - * K - #.
Non-display models with LEDs ( SM/M/N 100-200):
If the standard settings have not been changed, then the code *#4230 or code 12#345 leads to the opening of the intercom.
In newly installed intercoms, the codes *#423 and 67#890 are likely
You can enter the service menu:
#999 - beeps 2 times - (master code, default 1234) - beeps 1 time. If the code is not correct, it will beep with a two-tone signal. Master code can be 1234, 6767, 3535, 9999, 12345, 0000, 11639.
Further:
2 + # + 3535 Opening the intercom.
3 - Programming keys for entry. (Apply key + #, wait for beep + *).
4 — Erasing keys from memory.
* — Exit the mode.
# — Installation confirmation.
For intercom VISIT BVD-3xx(without display and LEDs), ( with right-sided or central location of the tablet)
opening the door - press 1 in the menu.
Doesn't always work BVD-34x (with left-handed receiver)
To be confirmed for them.
Cyfral intercom codes
To open the door we try:
a) If there are apartments in the entrance with numbers 100, 200, 300, 400, etc., then you can try to enter the codes:
call (code 1) call (code 2)
where code 1= "round apartment number" (100...900),
code 2= 2323 or 7272 or 7273.
For other intercom models (with the letter "M") suitable code:
"B" 41 "B" 1410. Sometimes it helps to simply enter 07054.
Intercom CCD-2094.1M(burning or flashing dash on the display) - dial the code B+0000 either opening immediately, or the service menu (inscription ON) - then press 2 . Either, the inscription OFF- then, alas, the quick access mode is turned off.
Intercom codes Cyfral CCD-2094M
Code 0000 "B" + pause 2 seconds. The inscription "cod" appears. Enter the code 123456+"B" or 456999+"B" (rarely 123400+"B"), pause 2-4 seconds, read "f0". Access to the menu is now open. To quickly open, just press code 601.
If we want to come regularly, we can write it down in memory Cyfral intercom your key. Press the bell and hold until the message appears, then enter the code 123456 (or code 123400). We got into service mode. In service mode, press 5, then enter the number of the existing apartment, the intercom will write TOUCH, attach the key - it is in memory. (For models with flat optical keys, instead of the apartment number, dial 600, insert the key and press call).
Codes Eltis intercoms
Typically the opening codes are:
"B" 100 "B" 7273
or
"B" 100 "B" 2323
But if it doesn't work, you can try other options from Cyfral.
METAKOM intercom codes
We press call, then the number of the first apartment in the entrance, call again ("COD" will be displayed), then code 5702... If it doesn't work, then we try the codes: 65535+"B"+1234+"B"+8 or or 1234+ "B"+6+"B"+4568.
Only for intercoms MK-20 M/T codes:
"B"+27+"B"+5702
or "B"+1+"B"+4526
And more about intercoms MK-20 M/T: Their firmware does not and will not contain protection for master keys. Even without knowing the service password, if you bring a blank tablet, the intercom will enter programming mode automatically!
Rainmann intercom codes
For Rainmann 2000 models and those with a dot on the left on the display.
Press the “key” button + 9 8 7 6 5 4. A double squeak should be heard. Then enter the code 1 2 3 4 5 6, the letter “P” will appear. Entered the menu. Further:
4 - Door lock.
6 - Turn off the intercom.
8 - Open the door.
DomoGuard intercom codes
Long press on "C", it will squeak.
Then quickly enter the code: 669900, + call button + number one greater than last apartment at the entrance. The display should read "F---".
Got on the menu.
Open the door - code 080
Remember new key- code 333
Disable door lock - code 071
Hacking Blink intercom
The only single-user intercom on the list. It has no screen, no keyboard, and mechanical locking. It is installed in houses with a concierge, so breaking it only makes sense at night. We find false bolts of an unusual shape on the lower section of the socket. These are contacts backup power. When 9 volts are applied to them (and they are just the width of the Krona contacts), the intercom is open.
Code intercom T-Guard
Code "B"+00000+"B"B" (the last two presses - quickly!) - the door is open.
Some general remarks for hacking intercoms:
In winter, intercoms with touch keypads (DomoGuard, Rainmann) are affected by hypothermia. We take a normal lump of snow and lean it against the keyboard. When the display shows “Err” (10-20 minutes), the intercom will unlock the lock.
Many wizards change the installer code (password) from the default (processor code) to another one. This is usually done so that no one else can change the intercom settings.
Now, to enter programming mode, you need to enter a new code... The old one has been changed and does not work.
No codes work, what should I do? Calmly. If the intercom has a magnetic lock (not a mechanical one!), then place one foot where the door opens and pull strongly on the handle. When pulled, the door opens, but nothing is broken.
For regular visits:
We seize the moment when the intercom door is open and stick several layers of tape onto the magnet. At the same time, we leave a small area of the surface for contact. At first glance, the intercom works as usual, but you just have to pull the door harder and voila, it’s open.
Methods for hacking other intercoms are currently being clarified.
The easiest way to open all intercoms is with one all-terrain key watch the video!
HOW TO EASILY OPEN ANY INTERCOM
Add to your page so you don’t lose it!
Code "VIZIT"
If the initial settings have not been changed, then the code for opening can be of 4 types: *#423; 12#345; 67#890; *#4230.
To open the door with service menu, we enter: #999. Next, we wait for two short signals and only after that enter the code: 1234 (standard), if the code does not work, then try the following: 0000; 9999; 3535; 12345; 6767. A positive response is 1 beep, a negative response is 2.
The service menu is controlled using 2 combinations and 3 buttons.
- First: “2” (short pause), “#” (another pause), “3535” - with this combination we simply open the door.
- Second: “3”, “put the key on the intercom”, “#” (wait sound signal) – in this way we add our key to the database.
By pressing “4” we erase all keys from the intercom memory.
Code "CYFRAL"
There are 2 ways to open the Digital intercom:
The first case - the intercom is marked with the letter “M”. To open such a system, enter:
“07054”, if it doesn’t work, then “call button”, “41”, or “call”, “1410”.
The second case, when the house has apartments numbered (100, 200, 300, 400), then we do this:
“call button”, “apartment number (100, 200)”, “call”, “2323; 7272; 7273 (one of three options)."
Code "METACOM"
You can open the METAKOM intercom using 3 different schemes:
- The first: “press the call button”, “enter the number of the first apartment of the entrance”, “press call again”, “the display shows the word COD”, “enter the code - 5702”.
- Second: “65535”, “call”, “1234”, “call”, “8”.
- Third: “1234”, “call”, “6”, “call again”, “4568”.
There is another METAKOM, which is slightly different in the opening method (METAKOM MK - 20 M/T).
To do this, we try 2 combinations:
- “call”, “27”, “call button”, “5702”.
- “call button”, “1”, “call”, “4526”.
Advice: if there is such an opportunity, it is better to call some apartment and state the essence of the problem (I think there will be kind people who will open it for you). Although more often the answer “ours” works.
Code "ELTIS"
Eltis intercoms were, are and will be the easiest to open, due to the fact that special codes they are of the same type and simple.
There are only 2 options for opening this intercom:
- "call button", "2323"
- "call key", "7273"
As you can see, everything is very simple.