For do-it-yourself open-end wrenches. Storing tools in the garage with your own hands: how to do it rationally and conveniently? Storing adhesive tape

Hello to all DIY lovers!

As you know, we all have to use open-end wrenches almost all the time. Literally every day, it is necessary to tighten or unscrew some nut on some device, both at home and in the garage or workshop.

Naturally, it is very desirable to have a full set of wrenches, or at least good set wrenches for nuts of the most common sizes.

I also have a similar set of keys, purchased several years ago. Moreover, these keys are quite compactly inserted into a plastic holder, which can also be hung on the wall.

I used to have this set hanging on my studio wall. However, practice has shown that with such placement and on such a holder, these keys are not very convenient to use.

Firstly, with this placement, the size of the keys is not visible. And since they are assembled quite compactly, you often have to make mistakes in choosing the right size key.

Secondly, the plastic holder shown in the photo turned out to be very unreliable, because after just a year of use it began to gradually deteriorate.

As a result, I decided to make a homemade holder for this set of keys, on which it would be convenient to hang or remove them, and the sizes of all the keys would be clearly visible.

In order to make such a holder, I needed the following supplies:

Materials and fasteners:

A piece of board 2 cm thick, 12 cm wide, and 95 cm long;

Magnetic knife holder;

Two wood screws 4x25 mm;

Two wood screws 4x40 mm;

Screws with press washer 4x20 mm;

Cambrics with a diameter of 5 mm, or similar plastic tubes;

The set of wrenches itself, plus an adjustable wrench.

Tools:

Drawing and measuring tools (pencil, tape measure and square);

A jigsaw with a file for curved cutting;

Electric drill-screwdriver;

Hand plane;

Metal drill with a diameter of 2.5 mm;

Metal drill with a diameter of 4 mm;

Spherical cutter for wood;

Screwdriver bit RN2, for driving screws;

Sandpaper.

Manufacturing process

To begin with, we use a plane to chamfer the front edges of the blank board, or better yet, even round them a little.

Then we mark the board that will serve as a holder, and drill holes with a diameter of 4 mm at its ends for the screws with which we will attach the holder to the wall.

We countersink these holes for the screw heads using a spherical wood cutter.

Now we saw off the ends of the holding board with a jigsaw.

Then we carry out the processing with sandpaper and screw the magnetic knife holder to the left side of the holder board.

For this purpose, I took an old short knife holder that was hanging in our kitchen. But now a new holder has been hung in the kitchen, and this one is just right for hanging the four smallest keys.

Immediately behind the magnetic holder, we prick with an awl and drill two blind holes using a drill with a diameter of 2.5 mm.

We drill these holes to a depth of approximately 10 mm.

The distance between these holes should be equal to the width of the handle of the key that we will hang in this place, plus approximately 10-14 mm, for large keys (from 20 mm or more), or 7-10 mm, for small ones (less than 20 mm.).

Then we cut off two identical pieces of cambric or plastic tube, approximately 6-10 mm long, again the length of these pieces depends on the size, and, in particular, on the thickness of the particular key.

By the way, if you don’t have a suitable cambric at hand, or it’s just a pity to use it for such purposes, then you can just use these plastic straws from bottles of liquid soap.

I just used them. These tubes fit well in diameter to screws with a press washer.

We put the cut pieces of the tube on screws with a press washer.

And screw these screws into the drilled holes.

And now we have a holder for the largest key ready.

We do the same for all other keys (remembering to measure the width of the handle of each key and select the distance between the screws based on it), including the adjustable wrench.

And now our holder is almost ready!

And then I decided, for greater clarity and ease of use, to make inscriptions on the holder with the sizes of each key.

To do this, I printed these labels on the computer.

Then I cut them out and taped them to the holder board on top.

The only thing is that I did not make stickers for the three smallest keys on a magnetic holder, since this is both inconvenient and unnecessary, since these keys are the most frequently used, and they are already very easy to distinguish.

And now our holder is finally ready!

Now all that remains is to screw it to the wall in a permanent place.

And hang up all the keys.

And now our holder is equipped with keys!

Here is its general appearance.

And this is a fragment.

As you can see, all the keys hang quite securely, and they are also easy to remove; you just need to take the desired key with your hand, slightly lift it up and turn it a little. In this case, the key is immediately in the hand in the working position.

In addition, it turned out that such a holder made of screws has another advantage. If the key hangs quite tightly, or, on the contrary, dangles, you can adjust it by simply tightening the screws supporting it and thus achieve the most optimal option.

In general, in my opinion, the holder turned out to be quite convenient and functional. Therefore, I can advise everyone who needs to make a holder for open-end wrenches to use a similar design.

Well, that's all for me!

Bye everyone, useful homemade products and good luck with your homemade creativity!

Many men use the garage for more than just parking. Often, tools or old things are stored in the garage that are a pity to throw away, and there is no room for them in the apartment. Also, the building often undergoes repairs or other work that requires tools and bulky materials. Thus, the structure often becomes similar to a warehouse.

Wall or hanging shelves in the garage - great way storing a lot of things without cluttering the usable space of the room.

Durable and reliable material designed for heavy loads. Metal shelves They can withstand a lot of weight and are convenient for storing parts and tools. The metal is also durable and wear-resistant. If the material is coated with a special composition against corrosion and rust, then structures made from it can last for many decades.

Unlike metal, wood is more affordable. Easy to process and does not require welding. Wooden shelves can also serve for a long time; the only drawback is their low resistance to changes in temperature and humidity conditions.

To improve wear resistance and durability wooden elements shelves, it is necessary to periodically coat the material with special covering paints. This will help the wood avoid rotting, deformation and damage by pests.

Other materials, such as plastic, plywood, stone, are rarely used for making shelves.

Design variations of suspended shelves

Can be open or closed. With or without back wall. Most often, a metal corner and a wooden base are used to make such structures. Suspended on the walls with anchors. The type of fastening can be permanent or dismantled.

These structures are made of metal angle, wooden base, a special cable or metal is used as side walls round profile, secured to special anchors.

These shelves are hung on special hooks driven or welded into ceiling beams ceilings Advantages of ceiling shelves - quick dismantling if necessary. Disadvantages - rather shaky design, which can sway when touched.

It is not recommended to store expensive tools or fragile items on such shelves.

Shelf in the form of a shield for tools

This design is equipped small shelves for storing small items and special hanging fittings. The shield consists of a strong back wall, fixed to the wall with anchors. Shelves, special hooks or tool holders are mounted on the wall.

This shelf is very convenient for carpentry and plumbing work. Most often, such a shield is hung in front of the workbench so that everything necessary tools were at hand. Sometimes the shield is equipped with additional lighting in the form of a lamp on a movable leg.

If you want to save useful space in the room, you can make a hanging shelf with your own hands and attach it to the ceiling.

Materials required for the manufacture of the structure

Tools for work

1. Drill with a drill bit for wood. The diameter of the drill must match the diameter of the stud.
2. A hammer drill for drilling holes in the ceiling for mounting anchors. The drill should be slightly smaller than the diameter of the anchor.
3. Wrenches, their markings must match the size of the nuts used.
4. Jigsaw.
5. Screwdriver.
6. Bubble level.

Work order

Step 1. To begin with, a shelf of the required width and length is cut out of a sheet of plywood or fiberboard.

It is worth knowing that it is recommended to place load-bearing studs at an average load on the material every 60-70 cm. If the shelf is longer, then over time plywood or fiberboard sheet will noticeably bend and sag.

Step 2. To enhance the strength of the material, it can be secured at the ends of the slab metallic profile, equipped with internal stiffeners.

Step 3. Holes for pins are marked along the edges of the shelf. It is worth knowing that it is advisable to drill 5-7 cm from the edges of the slab. If the holes are located too close to the ends, the material may crumble under the weight of the items placed on the shelf.

Step 4. After the holes are drilled, you need to attach the shelf to the ceiling and use a pencil to transfer the location of the holes to the ceiling. This way the structure will be positioned without distortion and you won’t have to worry about the studs becoming deformed.

Holes for anchors are drilled in the ceiling and dust is removed from them. The anchors are driven into the concrete all the way and the nuts are tightened.

Long metal studs connect to anchors placed on the ceiling. The connection is secured using coupling nuts. It is also advisable to secure the connection with an additional regular nut, which is screwed onto the thread of the stud.

Step 5. After the studs are firmly fixed to the ceiling, the period of installation of the shelf begins. A nut is screwed onto the stud, then a washer. After this, a shelf is strung on the ends of the studs.

The shelf is fixed using a Grover washer and a control nut. The washers protect the shelf holes from breaking under loads. The bushing serves as protection against loosening of the fastening nut. You can use two nuts for safety and greater structural strength. Final fit fastening fittings carried out by level.

Such hanging shelf will significantly save space in the garage. The only drawback is the mobility of the structure. You can eliminate it using a special metal corner. One edge of the corner is attached to the wall, the second - to the base of the shelf. In this way, the entire suspended structure. Also, a metal corner will strengthen the shelf, which will affect its durability.

DIY tool shelf

In order to have all the small tools at hand during plumbing or carpentry work, you can think over and make a special shield. Shield shelves are not distinguished by their high load-carrying capacity and durability; heavy tools cannot be stored on them, but for small and necessary things that always get lost, this design will be ideal.

It is important to know!

1. It is advisable to hang a shelf with tools on a plastered wall, otherwise condensation will accumulate between the brick or block surface and the wall of the shelf. Constant high humidity will negatively affect the shield material and may cause it to deform or rot.
2. Average load per one square meter shield surface should not exceed 14 kg. Weighting the structure will lead to rapid destruction.
3. The height of the shield is determined by the height of the garage owner. The top edge of the shelf should not be higher than human height. Otherwise, it will be inconvenient to take tools from the shield.
4. If there are shelves on the shield, it is not advisable to make them closed. This will also make the job more difficult. All small tools and parts must be in the public domain.

How to make a shield with your own hands

Materials and tools

Step 1. First you need to select the dimensions of the shield. Most often, such a shelf is fixed in front of the workbench at which a person is working. repair work. It is desirable that the width of the shield is not much larger than the dimensions of the workbench.

Step 2. Then a shield is cut out of plywood or other material. Places for small shelves are immediately marked on it.

Step 3. Then, using a jigsaw, the shelves with side walls are cut out. The side walls of the shelves can be made the same size as the length of the shield. Further using long screws The shelf structure is assembled and attached to the surface of the shield. Place for storing jars and boxes with nails and other small things ready.

Step 4. Attaching hooks. To do this, holes are drilled in the shield and dowels are driven into them and special threaded hooks are screwed in. It is advisable to think in advance where and what kind of tool will be located. Based on this, the hooks are drilled.

Then on back wall Eyelets or brackets are attached to secure the shelf to the wall. Final stage- mounting the shelf on the wall. Holes are drilled using a hammer drill and anchors are driven into them. If the shelf is fastened “tightly”, then you can strengthen the fixation of the structure using a special washer, which will prevent the eyes from sliding off the anchor.

A simple and convenient shield for tools and parts is ready. If you have all the tools and materials, you can make it in a few hours.

Video - Small shelves on the wall for storing keys and other tools

Almost all men living in own apartment, and even more so in a private house, they dream of creating at least a small workshop with a set of necessary tools. But quite often, due to inexperience, beginners simply do not know where to start. Therefore, the question arises - what tools are desirable to have on hand in the first place. And secondly, how to organize a workshop with maximum ergonomics, conveniently placing everything you need in it.

Let's try to provide all possible assistance. Today's topic: home workshop - optimizing space and convenient storage tools. Some recommendations will be given and shown successful examples. Well, you’ll have to figure it out and “adjust” it to the existing conditions yourself.

Tools needed for home

Even if the owner of the house is not a big fan of working in the workshop, you still cannot do without a certain set of tools on the farm. Therefore, in order to always have everything you need at hand, you should make a list and start purchasing tools. Sooner or later they will definitely come in handy both in an apartment and in a private house. It is clear that only people with a fairly high income can afford to buy the entire set at once. Usually the “arsenal” is formed over several years, and you can start with the simplest things.

By the way, even if a woman begins independent life, there should also be at least some tools in the apartment. But the list of “female recruitment” is much more modest.

In construction stores you can find ready-made universal tool kits. Perhaps they are suitable for those who use them only in extreme cases. In addition, often the instruments in them do not differ high quality. And most often, a home kit and consumable parts for it are acquired gradually.

So, in order not to run around the neighbors in search of what they need, each owner should have the following tools:

Illustration	Functionality
	A hammer with a metal striker (head). There is absolutely no way without this tool. It would be nice if it was a claw hammer, that is, two tools in one. Hammers with a rubber or wooden striker are also available for sale, but they have a specific purpose and are rarely used in ordinary household work. It is recommended to choose a tool with a high-quality wooden or modern polymer handle with rubberized grips.
	A set of screwdrivers, which includes tools with different tips. The main ones are cross and flat. The purpose of screwdrivers is to screw in and unscrew self-tapping screws, screws, screws. It is advisable that the kit includes at least three screwdrivers of the main types different diameters. They will be necessary for working with both small and large fasteners. The length of the metal tip of screwdrivers can also vary. For example, for hard-to-reach, recessed areas where you need to drive a self-tapping screw, you will need a long screwdriver. For work carried out on a work table, it is more convenient to use a tool with a short tip. Additionally, a tool is selected for specific purposes. For example, it would be good if the kit included an indicator screwdriver. It is necessary when carrying out electrical installation work, to check voltage, phase arrangement of wires, etc.
	Pliers (nippers, pliers). For homework the best option will universal option This tool combines both pliers and wire cutters. The former will help to clamp and hold an object, while the latter will easily cut a wire or wire. The handles of the pliers must be insulated so that, if necessary, they can also be used for electrical installation work. This tool is also necessary when carrying out metalwork and carpentry work.
	A set of wrenches is required when working with threaded connections, including hex bolts. The set should include wrenches of different sizes corresponding to the standard sizes of nuts and bolts. Wrenches should be in every set of household tools, as with their help you can quickly tighten the fastenings of a sofa or chair, table and bedside table, etc.
	Adjustable wrench - this tool, in principle, can replace a whole set of wrenches. Without it, it can be difficult to handle plumbing repair tasks. We remember that the key is quite large and quite massive, so it is not always convenient for them to work. However, it is unlikely to help if it is necessary to unscrew a rusted bolt. So it should rather be in addition to a set of wrenches, but not as a replacement for it.
	A hacksaw for working with wooden parts will be necessary when carrying out renovations in an apartment. In a private home, you can’t do without it at all, since you have to carry out a lot of everyday operations, for example, pruning trees. In addition to it, it’s a good idea to have a two-handed saw on hand if firewood is used on the farm.
	A hacksaw will allow you to cut a pipe, a metal rod, a thick cable, sheets of metal of small thickness, etc. Most often, the need for this tool arises among owners of private houses. When purchasing this type of hacksaw, you must immediately buy consumables - blades, as they break quite easily.
	An ax will most likely be necessary for a private home, as it is used during construction, repairs, and also for chopping firewood.
	The building level is useful for both an apartment and a workshop in a private house. It will help to achieve perfect evenness when hanging shelves or pictures, setting floor joists, masonry work and in many other cases. Depending on the purpose, its length is selected. For example, a short version (400 - 800 mm) is suitable for small apartment work, but a long tool is more suitable for arranging floors or leveling walls.
	A measuring tape is always useful both in the house and in the apartment. For example, to purchase flooring, carpet or other objects and materials, it is necessary to measure the dimensions and calculate the area on which they will be laid or installed. For apartment needs, a tape measure 3÷5 meters long is suitable. For a private home, and even more so for taking measurements on personal plot, it is better to purchase a ten-meter one with a soft ruler.
	Electric drill. This tool is a necessity in any home these days. In an apartment, especially if it is located in panel house, you can’t do without a drill when hanging cabinets and installing some plumbing accessories. To drill solid walls, it is better to purchase a device equipped with an impact function. For the drill, you must immediately purchase a set of drills different sizes on wood, concrete and metal, so that it is equipped for all occasions.
	A screwdriver is an indispensable thing in the home workshop that will help you quickly tighten a self-tapping screw or screw, or drill a hole in wood or metal. Using a screwdriver will make it much easier to make a shelf or repair pieces of furniture. Therefore, every homeowner should have this tool. In the kit with the screwdriver, you need to purchase a set of bit holders and the bits themselves of various types.
	An electric jigsaw will also an indispensable assistant when repairing or making useful things. It will significantly speed up the work of preparing material for cladding walls; it will cut thin slats, timber, thin logs and branches into garden plot. When making furniture yourself, you can use a jigsaw to cut sheet materials with the creation of complex curvilinear shapes. Having a jigsaw, you can often avoid buying hacksaws for wood and metal. But you should immediately purchase a set of files for different materials.
	A grinder or “grinder” is most often required for a private home, as it is intended for sawing materials that have a hard structure. It is used to cut slate, cut and polish metal. It is also suitable for cutting ceramic or even paving slabs. It often becomes indispensable for a car enthusiast in the garage.
	A caliper is a device that allows you to accurately measure products - their diameter, width, depth of holes, etc. On sale you can find a regular instrument or a digital version.
	A rechargeable flashlight will sooner or later be needed in any home, so it should always be kept charged. For example, the lights in the apartment suddenly went out or there was a leak under the sink, and it is urgent to find the cause of the accident. In a private home it is generally difficult to do without a flashlight, and its application has a wider range.

This table presents only the basic tools that should be present in the “arsenal” of any homeowner. Of course, everyone decides for themselves which ones to include in their home toolkit, and which ones can wait a while.

If the master’s hobby is electronics, jewelry, wood carving, making metal or wooden equipment for summer cottage or other areas, you will need special tools designed for a specific type of work. But such craftsmen don’t need any special advice. They themselves can give their recommendations to anyone.

Organizing a workshop and storage areas for home tools

A well-equipped workshop, with conveniently located tools and necessary consumables, is the key to fruitful, high-quality work

In a private house, usually even during its construction, the owner allocates a place for a workshop in advance. Or he organizes it in an outbuilding or garage. It is more difficult to allocate personal space in an apartment. But if it has a spacious storage room, balcony or loggia, then those who like to make things will immediately “occupy” this territory.

Some craftsmen limit themselves to a reliable table and purchased plastic organizing containers for storing tools. Others, showing ingenuity, come up with various cabinets, shelves or stands. They take up minimal space and do not clutter up even small rooms.

Setting up a workshop on the balcony

If the workshop is set up on a small balcony or loggia, and it is planned to be used year-round, then a number of measures must be taken. First of all, to create a comfortable environment in a room during the cold season, it must be insulated.

Insulating the balcony significantly expands the functionality of this room!

Cold balconies or loggias are not used in winter, and are often gradually turned into storage unnecessary trash. Why not turn it into an all-season space? – read in a special publication on our portal.

The second task, without which the workshop will be incomplete, is supplying electricity to the room and installing lighting fixtures.

When the room is completely ready, you can move on to planning your workspace. The plan, of course, will depend on the configuration of the balcony. As a rule, this is a very small area, often having a width of only 1200 mm. However, even within such limits, the craftsmen manage to arrange everything necessary for comfortable work.

The main thing in the workshop is a reliable and durable workbench. It is equipped with a thick tabletop that can support the weight of tools. Loads when applying forces during work must also be taken into account. The table must be well lit, so when laying the wiring, this must be taken into account.

Prices for tool boxes Plastic Cenntre

Tool box Plastic center Blocker

To store tools, shelves are attached above the table. And under them on the wall you can install metal hooks or other devices for convenient placement of small hand tools. There are quite a lot of such ideas, and they will be discussed in a separate section.

The main tool that is used most often is installed on the table. If it is large enough, then it should be placed so that there is room for other work.

An excellent option that will help save space and allow you to keep all your tools in order is a transforming cabinet. Such a cabinet involves the use of not only its main space, but also doors. Horizontal jumpers are fixed to the sashes, which are not only stiffening ribs, but also functional shelves.

The set with the cabinet also includes a work table, which is mandatory for the workshop. In the example shown above, it has a foldable design. However, the tabletop and its support must be reliable.

The cabinet opens and the table unfolds only when any work is planned to be done. The rest of the time it is compactly located near the wall.

The design of the cabinet is simple. It is assembled from timber and plywood of different thicknesses. Therefore, it is quite possible to make it yourself to the specific dimensions of the available space. If this is not possible, then the cabinet can be ordered from an experienced carpenter, providing dimensions taken from the site of its intended installation.

Don't forget about the space created under the table. There can be quite a lot of space for arranging closed and open shelves. To keep neat appearance workshop, on the shelves under the table you can install the above-mentioned plastic containers with tools.

Another option for expanding your workspace. It's about about installing mobile cabinets and racks with tools under the table. Naturally, such pieces of furniture will have to be adjusted in terms of parameters to the height and width of the table. An extended cabinet immediately increases the area of ​​the workbench, since its surface can also be used for work.

If the space on the balcony is completely limited, or there is none at all, then a wall cabinet is suitable, which can be placed even in the hallway. The photo shows two cabinet options. One of them has a door made of solid plywood, and the second one has a door made of perforated plywood. Thanks to the holes in the door leaf, you can attach some tools to it using hooks. However, this model can hardly be hung in the hallway. A solid door will completely hide the contents of the cabinet, and its surface can be disguised, for example, with a mirror. Notice the many drawers in the closet. Perfect place for storing various sorted “trifles” and fasteners.

Setting up a workshop in the garage

Another place where a workshop is most often organized is a garage. This is understandable, since the machine requires periodic maintenance, and a large number of the instrument is placed here. Therefore, it is easier to combine everything you need in one room.

If the garage is wide and long, then shelving can be placed along the far and side walls. This layout results in a spacious work surface and a large space underneath. Everything you need can easily fit here.

For the purpose of safe operation of both the workshop and the garage itself, it is recommended to make floor racks, as well as hanging stands, from non-flammable material. If wood is chosen for the manufacture of wall shelves, it must be treated with fire-retardant impregnation.

If the garage is not wide enough, there is still enough space along the back wall to organize a workshop with a work desk and numerous cabinets. The only thing that needs to be taken into account for any garage workshop is the intensity of lighting. Such a building, as a rule, lacks windows that let in natural light. And we have to compensate for this with electric ones.

If there is no desire or opportunity to stretch racks with tools over the entire length of the garage, you can apply the idea retractable design shelving. Moreover, if you correctly place the retractable panels, then in combination with them it is quite possible to organize and work surface. When the panels are moved to one side, a fairly spacious and reliable table top is revealed, allowing the necessary work to be done.

To create such a structure, you will need panels, for example, from MDF. You can perform perforation - this will significantly reduce the weight of the panels, and the holes will be useful for fixing tools. Small wheels are attached to the top and bottom sides. In addition, guides will be needed to ensure free and smooth movement of the panels. They are fixed on the desktop and on the ceiling. Or on the shelf provided above the workbench, which will also not become superfluous.

If the garage is not only narrow, but also short, and it is necessary to organize a workshop in it, then suitable option folding table. When not needed, the tabletop of such a workbench slides down along the wall. Well, you can place a stand above the table or hanging shelves with a tool. The garage space will be significantly saved, and the countertop will not interfere with placing the car in the garage or performing certain maintenance work on the car.

The option of placing tools on stands mounted above the desktop is convenient because everything you need will always be in sight. Thanks to this arrangement, you don’t have to look for the necessary consumables or, for example, a wrench or a screwdriver required size. The stands have boxes with cells for bolts, screws, nuts and other small elements. Moreover, for convenience, the boxes are located at a slight angle - their contents are immediately visible.

The upper shelves, which have greater depth, can be used for storage electric tool, and for various compositions also necessary to perform certain types of work.

This arrangement of the work area can be organized both in the garage workshop and on the balcony.

The option of a compact but spacious cabinet is ideal for small room garage. And that's all necessary tools And Consumables distributed very ergonomically. Top part cabinet is reserved for storing tools that have the average size. His Bottom part is a kind of chest of drawers with numerous narrow drawers. Thanks to the correctly selected height of the drawers, order will always reign in their cells, since each item stored in them has its own place. When drawing up a design for such a cabinet, you must immediately plan in which drawer what will be stored. Depending on this, choose the height of the sections. Well, even a novice home carpenter can make such a cabinet.

The mobile version of cabinets or carts for tools solves many problems. This allows them to be used in different places garage, as well as in the yard area. Such convenient devices do not take up a large area, and thanks to fairly large wheels and specially designed handles, they are easy to transport. At the same time, they contain many of the necessary heavy tools.

The mobile cart can be purchased ready-made, as they are presented in a sufficient range wide range. But it won't be cheap. Therefore, it is best to draw up a drawing and make it yourself from timber and plywood. And powerful wheels are easy to find in a furniture hardware store.

Useful little things when setting up a workshop

This section presents some ideas from readers that will contribute to the optimal organization of the workplace. Many of them will have virtually no impact on the family budget.

A great way to save space and always have consumables in sight is to keep them in clear plastic containers shaped like jars. You can buy them ready-made or use containers left over from various products to make them. Some workshop owners use instead plastic containers glass jars, but they have to be handled extremely carefully. The principle of their fastening is as simple as possible - the covers are screwed from the inside with self-tapping screws to the bottom surface of the shelves or wall cabinets. And it turns out that these surfaces also become functional.

Another approach can be taken. Side part plastic cans cut in half to the neck, which should remain intact. In this case, the lids are screwed not to the bottom, but to the side surface of the wall cabinet, which is also rarely used for storing tools. You get open containers-bowls for all sorts of small things. An example is shown above.

If you don’t have any plastic cans at hand, and glass ones don’t inspire confidence, then you can use bottles from drinking water, which will definitely be found in every home. A hole is cut in their upper part, convenient for removing the parts stored in them. Rings are screwed into the caps - for the convenience of hanging bottles on hooks or even on hammered nails.

There is usually no shortage of cans in the garage, and they can be plastic or metal. Any of them, unnecessary or unsuitable for direct use, can be put to good use. And evidence of this is the large number of ideas for using them. For example, if a good-quality steel or aluminum canister has been damaged and it is no longer possible to store liquid compounds in it, you should not rush to throw it away. This container will make a reliable and convenient container for storing and carrying tools. To make it, just carefully cut out the side of the canister. Then, secure the edges of the cut with a rubber sealing pad, secure the hinges and lock. And the internal space is divided into cells using plywood partitions and shelves. Such a container can be used to store some tools in the garage, in the trunk of a car, or on the balcony.

Depending on shape and size plastic canisters, from them you can assemble drawers for a cabinet, rack or cabinet. The main thing is that you don’t have to spend a lot on plywood and boards. And there is no fuss with assembling numerous boxes.

It is enough to cut out one of the sides of the canister, leaving the handle and lid intact - and the container is ready. Depending on the size of the parts you plan to store in this box, the size of the canister is also selected.

Many owners of home workshops have appreciated the convenience of magnetic strips on which bits for screwdrivers, drills, screwdrivers, scissors and other similar tools are stored. The ease of use lies in the fact that you don’t have to search for, take out, and then put back the tools. They can be easily removed and then reattached to the magnetic strip without much distraction from the work at hand.

Prices for FIT tool boxes

Toolbox FIT

If you have magnets (and you can find them if you want), then making such an improvement to your workplace is a piece of cake. You can look for ready-made magnetic shelves in furniture fittings or kitchen utensils stores.

But such a device for storing pliers, screwdrivers, scissors and other tools can be made by any owner who is starting to organize a workshop. To do this you will need segments of ordinary polypropylene pipes diameter from 20 to 32 mm. The cost of such pipes is low, and in addition, they can remain after repairs. The pipe is marked and cut into equal sections with a 45 degree bevel to one side. Then the location of the holders is also marked on the wall or board. After this, the prepared sections are fixed according to the markings using self-tapping screws through the protruding beveled edge. Instead of pipes, sections of durable reinforced hose can also be used. Fast, cheap, neat.

* * * * * * *

There are plenty of other ideas for arranging a workshop and placing tools in it. If you want to introduce innovations to your existing place of work, or finally start organizing it, then you can use the examples presented above. You can also approach the process creatively and use items that have been lying idle for a long time to create convenient devices. After all, in every garage or shed you will probably find something that is a pity to throw away, but there is no way to find a use for it. We will be glad if you share your improvement proposals on the pages of our portal.

In conclusion, there is a video in which the master shares his experience of creating a convenient tool storage system in the workshop.

Video: An example of a self-made system for ergonomic tool storage in a workshop.

In many cases, the garage serves universal workshop. Tools for all occasions are stored here: for car repairs and for repairing home furniture.

This function is greatly expanded if the garage is built with country house or at the dacha. Here the owner simply has to be a jack of all trades master- lay electrical wiring to the gazebo, sharpen a knife and an ax, repair a lawn mower, refuel and lubricate a snow blower, plan a new one wooden beam for leaky support under grapes...

All this troublesome work requires various instruments And devices, which you've probably already had for a long time.

But how can they be conveniently and rationally placed?

Garage space zoning

First of all, let's go into the garage with a tape measure, a pencil, a notepad and a strong desire to finally get rid of the trash that we've been sorry to throw away for years - what if it comes in handy someday?

The design principles of such production and storage facilities presuppose their clear functional zoning.

But meanwhile, you have long ago, without knowing it, divided the garage into functional zones.

In one, at the entrance, something necessary is kept at hand daily, and in the far corner it gathers dust rarely sought after. Small tools are mixed together in a small box, heavy hammers and sledgehammers rust under the wall on the floor. Somewhere there are containers with antifreeze and transmission oil in a pile.

We will apply this intuitively correct distribution when designing ordered placement of tools.

First, let's estimate and draw

Let's define wall, along which we will build racks and shelves for tools. Data about its height and width entered into the notepad will become Starting point for a drawing of future storage facilities.

Having decided on the location of the tools, we will, in turn, divide "instrumental" zone to clear structures where tools, fixtures and fasteners will be located:

• for a car (locksmith);
• for electrical work;
• for welding work;
• for carpentry work.

DIY tool shelves in the garage: materials and design

Tool rack design and material The material from which it will be made will determine the size of the free space into which it will have to be “fitted,” as well as your technical imagination and acquired or completely absent skills for such work.

In any case, it is wise to preface your own project by visiting the Internet sites of garage DIYers, where already completed projects are displayed for everyone to see. successful projects garage interiors.

But the main choice factor is yours budget, i.e. the amount you are willing to spend in the name of garage comfort.

DIY tool shelves in the garage - photo:

Convenient and simple rack

The proposed tool rack is just a concept, a sketch of one of the possible designs, therefore exact dimensions there is no point in pointing out. You will fill your size with numbers individual project.

Based on considerations of strength and durability, we will make a continuous shelving along the wall of the garage with shelves of different heights from a steel angle of 50x50 mm. We will make shelves from edged boards 4-5 cm thick.

We will need a grinder with discs for cutting metal, welding machine, a couple of packs of electrodes, an electric drill, a carpenter's corner, a water level, a carpenter's saw, a tape measure, a marker.

The number of supporting posts depends on the length of the rack. The step between them (respectively, the length of the shelves) is determined to be 1 m.

Important: We set the width (depth) of the shelves in such a way that they do not interfere with opening the doors of a car entering the garage. If this condition is met, a convenient shelf width will be 40-50 cm.

We mark the corner, cut it and weld it into a rectangular perimeter of the stand. According to the drawing, we mark, cut and weld into the perimeter the transverse corners on which there will be lean wooden shelves. We design them different heights, based on the dimensions of the tools planned for placement.

Don't forget about the special low section for boxes with fasteners.

We place the first shelf at a height 60-80 cm from floor level garage. In this lower space we will place fuel cans, bulky and heavy objects, spare units.

Racks weld to reinforcement rods driven into the wall. Along the top and in the middle, we weld around the rack posts with a horizontal jumper made from a corner or a steel strip.

Now it's time to take the hacksaw and cut the boards to size. Before installing shelves boards soak in hot drying oil, we’ll paint it in a day.

We hang everything that can be hung

Box spanner sets can be conveniently, visually and beautifully hung in ascending sizes on brightly colored boards attached to the wall in the depths of the shelves. Above each key can be glued paper sticker with size, large printed on a printer, or write the numbers by hand with a permanent marker directly on the board.

Making the most of vertical surfaces, in the same way we hang hammers, pliers and other tools with a configuration suitable for such placement on the side walls of the rack.

Watch an interesting video on how to make a shelf for keys in the garage with your own hands:

Conclusion

Many motorists have had garages for a long time perfectly equipped, the tools are placed rationally and conveniently - so that they can be taken from their usual place with their eyes closed.

Please, tell us about your comfortable garage, share your experience with novice colleagues in this truly masculine hobby.

No matter how large the garage, the problem of compact placement of all the equipment necessary for the household is always relevant. Storing the tool on the wall will help solve the issue in many ways. limited space- this way, what you need will be at hand, and useful meters will not be used in vain. By organizing a tool storage system on the wall, you can solve many problems overnight. Each type of repair gear must be placed separately, this will make it easier to find this or that item in the future. Next, let's take a look at the most popular and simple ideas for mounting a tool on the wall.

Organizers made from cans for tools on the wall

If for some time cans If you don’t throw away canned food, you can build an excellent organizer for storing tools on the wall with your own hands. Pliers, secateurs, scissors, brushes will be organically and conveniently placed in tins attached to the walls of the garage. Such simple idea will allow you to make the most of your workshop space and keep all the necessary tools at hand.

Screwdriver holder

A screwdriver is a very useful household item. But finding it becomes a common problem, since it is small and unnoticeable. So that all screwdrivers are at hand, and efforts to find the item the desired model reduced to a minimum, a holder can be built. To do this, you just need to drill into wooden block holes and attach it to the wall.

Shelf with grooves for tools

Drills, jigsaws and screwdrivers love order no less than any other household assistant. It is convenient to store them on a shelf with cut holes.

garden tools

How to hang tools on the wall in the garage? No one wants to step on the same rake day after day, however, if they lie anywhere in the garage, this will happen more than once. A smart solution would be to remove them from the walkway and securely attach them to the wall. Holders cut from ordinary PVC pipes can help with this.

Racks with containers

Useful little things can be conveniently placed in containers on shelves. You can use pallets to build a rack; you may have left them after building a garage or house.

Important! If you want the rack to be more mobile, you can attach wheels to it.

Organizer for small parts:

• It is convenient to store small useful items, such as screws, nuts and nails, in bottles or jars made of transparent plastic. To save space on shelves, containers can be attached to a hanging holder.

Important! It is more advantageous to make the mounting location on the lid of the container.

• Empty cut canisters can also be used to store the same tools.

Important! To avoid searching for the necessary parts for a long time, it is better to label the containers.

Band saw storage

It is dangerous to store canvases band saw rolled into a ring, because in the process of unrolling them you can get seriously injured or injured. To store such tools safely on the wall, you can use office clips. They are used to secure a sharp blade, hang it on a hook or place it on a shelf.

How to conveniently store drills and keys?

Another type of small household utility is various keys and drills. A tool mount on the wall can be made from magnetic tape. This way, the drills will not get lost and will always be in order.

Storing adhesive tape:

• It is very convenient to store adhesive tape or tape in a box with a metal strip dispenser. This way you can easily tear it off required amount tape without losing its ends for convenient later use.
• Another convenient method for storing duct tape is to use coat hangers. By cutting the bottom of the hanger, you can hang some duct tape and tape on it. The hanger itself can be hung on a hook driven into the bottom of the shelf.