DIY children's houses made of plywood - drawings. Children's playhouse in the country

home

Programs

Many summer residents, when planning, intend to build at least a small children's house with their own hands, so that the little owners have something to do and a place to play. summer time. That is why we decided to write an article where we describe in detail the process of creating this small building Location on.

In our case, the height of the ridge of the building will be 90 centimeters, and the overall dimensions will be limited to the following indicators - 160x160x140 centimeters. To build a children's house you will need the following tools and materials:

Screws with nails;
4 foundation blocks;
Dye;
4 floorboards;
Edged board;
Lining;
6 beam holders;
Mounting corners;
11 bars for creating the floor and 5 for the roof;
Carved platbands;
Furniture board.

Work order

Assembling the floor frame. The first step is to create the foundation of the future structure, followed by reinforcement with metal corners and diagonal alignment.

Definition with a site. You should choose level place. If there is none, then you will have to first level the area for construction. On the site, using a frame, it is necessary to mark four corner points, which will become markings for placing the foundation blocks.
Adding stability to the base. Before laying out the frame of the house, follow the surface sand cushion place four foundation blocks to a depth of no more than one spade bayonet. After this, a waterproofing material is laid between the frame and the base.

Execution of the floor. The next step is to completely cover the frame with boards, thus obtaining a flat surface.

Processing the bottom side. After the floor is assembled, it is necessary to treat the outer surface of the boards, that is, the one that will subsequently be adjacent to the ground. Next, you can begin to build walls, insert doors and windows.

Important point! To build a children's house with your own hands, you should only select jointed materials. This way, children will not get injured or get splinters while playing in a small building. For the same purpose, it makes sense to chamfer the corners.

Rafters. First of all, on work surface preliminary markings are drawn. Afterwards, bait is applied using temporary nails. The next step is to secure the rafter and seal all the joints with corners. At the end the nails are removed.
Fastening the rafters. To install exactly plumb, 3 rafters should be placed on the frame, supporting them with an inclined support. The walls of the future children's house will be attached to the frame with metal holders.

Wall cladding. A self-assembled frame can be sheathed with different materials, but lining is most often used for this.

Roof assembly. Starting from the ridge, the roof of the house is sheathed with carved boards on both sides. You can lay ondulin on top of it, which can be quite easily cut to size using a grinder.

Exterior decoration. Having finished building a children's house, do not stop there - decorate appearance a new building for a child, making the structure more elegant and beautiful. To do this, you can embellish the corners of the building with figured corners, and the doors, windows and ends with carved platbands.

Interior. You should not lose attention by placing, for example, a small bench or table inside.

This way you will get an almost finished children's house. As you can see, doing all the work yourself is not at all difficult. In the end, all that remains is to simply paint the walls of the new building.

Children's house on poles

You can easily build a playhouse for a child yourself at summer cottage, right in front of the house. One of the most common options is a do-it-yourself building on poles.

Instructions for work

Of course, the new structure on the site will not be very heavy, and therefore there is no need to build a foundation for it. However, some kind of foundation will still be required even for a children's structure. In our case, it is best to use a wooden beam 100 by 100 millimeters. You can fasten the timber together using steel corners.

The next step is to place the supports that will hold the top floor of the children's house. For this purpose, it is worth using boards with a thickness and width of 30 and 80 millimeters, respectively. For fastening, jumpers will be useful, which will simultaneously hold the boards of the 2nd floor.

Along with this, they are installed wooden supports, they will serve as supporting structures for the stairs. A wooden floor is installed.

Expert advice! To ensure that the ceiling of the future structure can support a heavy load, it is recommended to place the boards with the edges down.

It is best if the supports of the building are placed not just anywhere, but on a paving slab surface.

To prevent children from getting hurt while playing, it is worth installing balusters with railings on the stairs.

At the top, the supports must be fixed to each other. Jumpers should be used to secure the wall frame.

You can sheathe walls using regular boards, it is recommended to use plywood for the roof.

For greater safety and to avoid injuries to children, before building a children's house, you should sand all the timber yourself. In addition, it is better if you inspect all the boards in advance for chips, cracks and breaks in order to minimize the risk of splinters during the operation of the building.

Almost any modern soft roof can be used for the roof.

In addition to the main entrance, it would not be amiss to include in the design of the house for children a “black” or simply an emergency exit. For this purpose, you can make a small hole in the floor of the structure where the rope will be pulled. Undoubtedly, the guys will appreciate this decision!

Towards the end, finishing work is carried out, for which various decorative elements and multi-colored dyeing materials.

Finally, between the pillars, under the first floor, you can create a sandbox.

Master class on creating a house with your own hands

First option

To work you will need following materials:

Wooden corners.
Edged board.
Tongue and groove board for creating a floor.
Nails.
Metal mounting brackets.
A block for the frame with a section of 45 by 45 centimeters.
"Biotex".
"Block house".

Before you start creating a children's house with your own hands, you need to draw up a drawing of the future structure. In our case, the building will contain one single room with a doorway and a window and a small veranda.

As you know, any construction work begins with grounds, which will simultaneously play the role of gender. Three joists are connected together with tongue and groove boards using tongue-and-groove fastenings and nails.

After this, the frame of the new building is made from timber. Do not forget that to fasten the bars you should use metal corners.

To prevent the material from being damaged and spoiling its appearance during the process of attaching the “Block House”, it is necessary to use scraps and a hammer.

Wall cladding should be done based on the location of the doorway and windows.

Corners on the street side are covered with wooden corners.

For the roof, edged boards are used, which are fixed on each side with nails. It is recommended to make the flooring from bitumen shingles.

After you have completely built a children's house with your own hands, it is necessary to treat the walls, floor and roof of the structure with biotex. This composition will not only give the surfaces the desired color, but will also further protect the building structure from negative impact rain and sun.

Like last time, shelves, a table and benches are made inside the room.

Thus, with our own hands, without the help of specialists and additional costs, we will get a beautiful and reliable children's house, which your children will certainly appreciate.

Second option

In the second case, to build a house you will need the following components and materials:

Thin boards.
Ruberoid.
Six wooden planks 2.4 by 1.8 meters.
Set of screws.
Bars of various sections.
Stain.

It is recommended to lay the foundation using crushed stone whenever possible. An alternative is to simply level the ground beneath the new structure. Next, the bars with a section size of 10 by 10 centimeters must be cut into equal parts, and then placed with a step between the posts of 1.4-1.5 meters.

The support bars should be placed under the posts in the soil, this way we will eliminate the process of rotting the floor in the future. We place bars with a cross section of 5 by 10 cm between the rack and the panel, which will later become hollow. Fixation of the beams is achieved using screws. Any voids between the joists should be filled with earth.

The next step is to cut wooden panels into equal parts, and then lay them out in a strictly horizontal position. Fastening is achieved through timber.

In order for the flooring to be as smooth as possible, the panels should be laid with a small margin, and then saw off the excess parts.

Next comes work on creating the side panels. IN in this case Initially, markings should be made, leaving at least a 6-centimeter margin on each side. As for the height of the wall for a children's playhouse, 1.5-meter panels can be made as an example.

In the process of assembling walls with your own hands, you should not forget about door and window openings, which are also created based on pre-made markings. In our case, the door dimensions will be 0.6 by 1.2 meters.

Internal and external panels are varnished. After the flooring is well fixed, the walls are attached to it using screws. A board with a sectional size of 10 by 5 centimeters is placed with a slight protrusion beyond the edge on the side.

As soon as new wall will be placed in place, its installation must be checked using a level. Only after making sure that the location is correct can you move on to the next wall!

The next step is to construct a roof, which is finally covered with a layer of roofing felt. To cover gaps that may accidentally form between the panels, you should use a wide ridge.

For greater beauty, you can create shutters on the windows or assemble a small porch in front of the house with your own hands.

At this point, the children's building will be ready.

Overhead building with stairs and slide

An interesting option would be a children's house built on dacha area on a hill. In this case, the following materials and products may be required:

Dye.
Ladder.
Chipboards.
Sand and cement for the base.
Slide.
Wooden bars for piles.
Screws and nails.

This version of the structure will be built mainly thanks to a tongue-and-groove connection, which will allow, if necessary, to dismantle the building, for example, for the winter.

The frame of the house is assembled in the same way as shown in the photo below.

If you are going to install shutters on window opening, then you should buy hanging hinges in the store in advance.

The railings under the porch are being assembled. For this purpose, small holes are made in the bars with a certain pitch, with a depth of no more than half the bar.

The slats should be tried on together with the drilled recesses. After making sure that the slats fit well, they should be removed for a while and secured with nails for greater ease of painting work.

The most important point in the construction of any structure is laying the foundation. Children's house is no exception! In our case, it is necessary to dig 4 holes under the building piles, the depth of which will be approximately one meter. Next, the supports are poured cement mixture, after which it remains to wait for final drying.

It is important to emphasize that the deeper the piles are placed in the soil, the more reliable it will be finished design at home, reducing the risk of collapse and mobility of the children's building.

As an option for such a quiet corner, you can consider a children's house made of wood.

Children's house made of wood

Children's houses can be divided into two large groups, some are intended for children from 2 to 6 years old, others for those over 6 years old.

But building a wooden house for children with your own hands is half the battle. Another question is how to arrange it?

A house for the little ones can have absolutely Not big sizes 1.7*1.7 in plan and height 2.5 m.

Dimensions: 1.7 x 1.7 m around the perimeter and 2.5 m in height, which is quite enough for children aged 2-6 years.

The building for older children should be larger, for example, in terms of its dimensions it can be 2*3 m and its height is about 2 m.

Children are crazy about houses built on tree branches. If there is no such direct possibility, then you can simply raise it to a certain height. By the way, in this version the house can protect the logs of firewood.

During construction orphanage made of wood, all its parts must be carefully polished. This is necessary so that its residents do not get scratched or pick up splinters. In addition, they must be coated with drying oil in at least two to three layers.

Of course, in addition to wood, it is also possible to use other materials, for example, plywood.

To build an orphanage there is no need to order separate project. To calculate the required amount of material and complete the work, a self-made sketch will be enough. It should reflect all the main dimensions.

It is advisable to use the material that was used in the construction of the “adult” house. By the way, for the orphanage you can use the waste that remains after the completion of construction big house. In order to build a children's wooden house with your own hands, you will need:

Wood hacksaw;
Tape measure, plumb line, level, square;
Chisel;
Electric tools – drill, jigsaw, screwdriver;
Fasteners

For execution finishing works, can be used paints and varnishes and tools for working with them, of course, one cannot discount plywood, the thickness of which must be at least 10 mm. Directly for the construction of a house you may need 50x50 timber.

We must not forget about roofing materials, bricks, etc. In order to increase the safety of operation of such a house, it makes sense to install ready-made plastic windows and doors.

Construction of a wooden children's house with your own hands

A wooden house for children at the dacha can be built in the same sequence as for an “adult”. That is:

foundation arrangement;
construction of main walls;
roof device.

Yes, in order to save money, you can simply paint the house, but we're talking about about the safety of children, so it makes sense to cover the walls with sheet material, such as plywood. This will reduce the likelihood of injury while staying in the house.

Children's playhouse safety

It makes sense to make the front door the full height of the wall. This will protect the child from getting bumps on the top jamb, and it will be easier for adults to enter. To avoid injury, the walls of the house must be lined with plywood or fiberboard. That is, they should be smooth. The roof in such a house should exclude the possibility that a child will want to climb on it.

Project plan, specifics

When drawing up a work plan, it makes sense to take into account the specifics of the orphanage. So, the distance from flooring to the ceiling must be at least 1500 mm. When building a house, it makes sense to install at least two windows. This approach will provide decent lighting inside. In addition, through these windows, parents will always be able to see what is happening inside and immediately intervene if necessary.

Preparing for work

For construction, it is necessary to carry out certain preparations, that is, purchase required material(timber or log), cement, boards, finishing materials. The volume of purchases will become clear after a design sketch has been drawn up.

Construction of the foundation

This design is lightweight and therefore there is no special need to build a strip foundation, even a shallow foundation. You can get by with small columns of two or three bricks, which will be installed at the corners of the perimeter of the future house. During their installation, it is necessary to ensure that the tops of the columns are located in the same plane. As an option, you can consider making a monolithic slab.

This structure will need to be equipped if a columnar foundation was used as the base. This is necessary to evenly redistribute the load created by the house.

As a basement structure, you can use interconnected beams on which wall elements will be erected. When raising walls, one must not forget about laying a layer of waterproofing material.

If the children's house is built as a small copy of the “adult” one, then, most likely, it may need to be connected to the sewer system. To do this, you will have to lay a pipeline from the house to the entrance to the main sewer system.

It must be borne in mind that all actions related to insulating pipes, etc. must be carried out like an adult.

To create a floor, you need to install logs. If the children plan to use their house in winter time, then, most likely, you will have to equip the floor with appropriate insulation. To do this you need to do everything necessary operations, that is, fasten to the joists from below unedged boards, lay down vapor barrier material, insulation. On top of the subfloor, you can arrange concrete screed. It will be possible to lay the finishing coating on it later.

If a decision is made to build a house according to frame technology, then you will have to build a wall frame. For example, for a wall in which a window will be installed, the construction of a frame consisting of several beams will be required. Two at the edges, two directly in the place where the window is planned to be installed. By the way, you will need to install two horizontal bars under it. A window will then be installed in the resulting opening.

For blank walls, it is enough to install four vertical bars. If we assume that the width of the insulation mat is 600 mm, then the distance between the racks should be 10 mm less, this will allow the mat to be installed with tension and prevent the formation of cold bridges.

For a children's playhouse, it makes sense to install windows made of metal-plastic. It's just safer. It is quite difficult to make such windows yourself, so it makes sense to invite specialists who are engaged in the production and installation of such products.

Insulation can be done by everyone accessible ways. For example, using mats made of mineral wool. But you can use ecowool. This is a harmless material that does not cause allergies. When laying it, it is necessary to use specialized equipment.

It must be remembered that a staircase is a source of increased danger for both children and adults, and therefore, during its construction, it is necessary to be especially careful and it is advisable to study the documentation necessary for this case (GOST, SNiP, etc.).

As an option, you can consider a staircase made on a bowstring.

A few words in conclusion

When constructing a children's house on the territory country house You must always remember the safety of those who will use it, that is, children.

All sharp corners must be smoothed; for this you can use both manual and electric tools.

Video on the topic: do-it-yourself children's wooden house

1 Building a house for a child with your own hands.

2 Children's playhouse

From the point of view of psychologists, every person and especially children need their own territory. It’s not for nothing that they have a craving for building huts, huts, bases and other buildings from any suitable or not so suitable materials. If you have your own yard or your child spends a lot of time at the dacha, build him a children’s house. The easiest way is using frame technology. Examples of the construction of wooden playhouses for summer cottages in photo reports.

Playhouse for a summer cottage with a sandbox below

We bring the brought timber 100*100 mm until smooth. You can use a plane, or you can use a drill with attached sandpaper. First with large grains, then with small ones. Afterwards we treat it with a protective compound against rotting and paint it. While the pillars are drying, we drill holes (our diameter is 23 cm, depth 60 cm). We fill them with crushed stone at the bottom near a shovel. We put up the pillars, set them vertically, fill them with crushed stone, compact them, and concrete them.

We cut the exposed pillars all to the same level. We fix the same 100*100 mm beam on top. It is also carefully processed so that there are no splinters. We connect it into half a tree: at the ends we cut out recesses half the thickness of the timber. For a 100*100 mm beam, cutouts are 50 mm deep and 100-100 mm in area: so that the same sawn edge of the other beam lies flat.

We fix the top beam. Three have been collected, the fourth is still lying around.

We fasten it securely: 2 long nails (200 mm) on top, corners on the sides with self-tapping screws.

We attach an additional beam along the long side. Under it in the middle - above the stand - we cut a notch, also half the thickness of the beam - 50 mm. No more preventing wood from splitting. We cut down the timber at the ends in the same way as those that go along the perimeter: half a tree. It fits into the prepared gash.

A children's house must have a solid margin of safety. Therefore, we play it safe in every connection. To give the structure stability under lateral loads, we will install jibs. We cut them from 50*50 mm timber, sawing the ends at 45°.

We put it at a standstill, squeezing well.

After installing the jib, we lay the board. This will be the floor of the house.

Without an assistant - no way

We cut the flooring from the boards. It is more convenient to work with a jigsaw, but you can also use a hacksaw.

On the finished flooring we assemble the frame of a children's playhouse. We use timber 50*50 mm. We position the beams strictly vertically, first fasten them with nails - two on both sides, then reinforce them with corners on self-tapping screws (also on both sides).

We increase the rigidity of the structure by installing jibs. Then we nail the second floor trim. We simply nail these beams between the pillars. They must be sawed off with great precision so that the building does not warp. We strengthen the joints with corners, then install the jibs.

We do not nail the jib in the place where the entrance will be.

They covered it with boards left over from the packaging of the equipment. You can use it from pallets, buy an inch board (12-13 mm thick), cover it with clapboard or imitation timber, logs, siding.

When the sheathing is almost finished, we begin to assemble the rafter system. It's easier, of course, to do pitched roof— make one wall higher and no problems. But the gable one looks better, although it is more difficult to execute.

For rafter system We put two boards on an edge, connect them at the top, sawing off the corners. The ascent depends on the desire and amount of snow. If there is a lot of snow, raise your skate higher. If not, maybe about a meter or less. We knock it down with nails, then we strengthen the connection with overhead plates.

When building houses they put here or metal plate or a piece of board. We decided to use a board.

Using the finished sample, we mark the other rafters. Cut it out, knock it into two rafter legs at an angle (all should be the same as a carbon copy). Having installed it on the top of the house, we check the verticality. Then we nail it with two nails on both sides and place the corners.

Now the sheathing boards are laid on the rafters. The roofing material will be ondulin. We place the board 11*100 mm in increments of 30 cm.

Based on the thickness of the board (11 mm), we use self-tapping screws 25 mm long to fasten the ondulin (so that they fit well into the board. We put rubber gaskets under the caps to prevent leakage.

Railings made of treated, sanded boards. Screwed onto powerful 90 mm self-tapping screws. Two for the bottom beam - one for the sheathing board.

Railings are installed on the “veranda” of the house

At the top, the railings are connected by a 30*30 mm beam. Then a board will be nailed to it - a handrail.

Railings ready for painting

It was decided to put a sandbox downstairs. It’s not difficult to assemble: eight boards on the walls, connected at the corners with bars, with a side board nailed on top. Then the sandbox is painted.

Even a “non-builder” can build such a children’s house with his own hands. There are no particularly complex jobs; you can get by with basic tools.

Several options from the same series are pictured below. Two are houses with a slide, and one is a one-story option, more suitable for girls.

One-story “open” option

How to make a children's house from OSB and plywood (frame technology)

It was decided to make a house using frame technology - the base is made of boards, the cladding is made of OSB. Dimensions in plan - 3 * 2 m, wall height 1.5 m, at the ridge 2.2 m. 50 * 100 mm boards were purchased for the frame, inch board (100 * 12 mm) for the subfloor, 9 mm OSB for the floor and external cladding, for the interior - polished plywood FSF 6 mm, foam for insulation 100 mm thick.

Preparatory work - assembling panels for the children's house - was carried out in the garage: it was still cold. Later, as it gets warmer, the house will move to the dacha, to a place of permanent residence.

The first stage is the manufacture of the floor frame. We knock down a rectangle with sides 3 * 2 m, nail the transverse boards (floor joists) in increments of 50 cm.

The floor will be insulated with foam plastic. Children love to sit on the floor, so we insulate them well - with 100 mm foam plastic. We stuff thin strips underneath it from the bottom so that it doesn’t fall through. Insert foam. Gaps can be filled polyurethane foam.

It's good that the building is small. We put it on its side and hem it underneath with an inch board. This will be the subfloor. After turning it over, we sew up OSB.

Later, when the house was taken out to the country, a mistake was discovered OSB installation. They nailed him close. On humid air the material was swollen and the sheets were buckling here and there. Therefore, during installation sheet material leave a gap of 8-10 mm.

Next, we assemble the wall frame. We install the racks in 1-meter increments, and double them under windows and doors. Since the top will be filled with OSB on one side and plywood on the other, the structure will be rigid. We don’t install jib beams. They are needed if the children's house will be upholstered with clapboard or other slatted material.

Assembling the wall frame

The work has been moved to the dacha. Three old logs were used as the foundation. They are hewn and the tops are leveled. The logs are leveled, a board is nailed onto them, on which the platform will be installed. The width of the house is 2 meters, and the logs are 3 meters long. We will decorate the remaining part as a terrace or porch.

The platform was installed. It is attached to the logs with large pins that connect the log and the platform. We began to lay out the frame of the walls. They must be placed exactly vertically. To secure it, temporary cuts were used - they were nailed down with boards on the sides.

Fixed externally (connecting brackets are visible in this photo)

Along the way, having aligned and checked whether the wall is level, we nail it to the platform with long nails. The length of the nail is such that it at least reaches the middle of the frame board.

Then the fittings begin: you need to correctly saw out the corners for the rafters so that they lie evenly on the boards. First, we cut roughly, gradually ensuring that there are no gaps.

Trying to “create” a rafter leg

When the shape of the cuts is clear, we transfer it to other boards using a sharp pencil. We cut everything evenly (with a jigsaw, if you have one or hand saw). Then we nail all the boards to the frame. We fill transverse boards between the rafters - the ondulin will rest on them. It turns out to be such a house.

After the construction of the rafter system, only the sheathing remains - inside and outside. We fill the outside with OSB. We cut it so that the joints fall on the racks. We nail it, you can use wood screws. For whom is it more convenient?

The insulation of the house inside is mineral (basalt wool)

Everything is nailed on top with plywood. That's all. The job is done - paint it and you can put it into operation)))

Using the same technology you can build a tree house. It will be necessary to secure the platform, but everything else is very similar.

Drawings and diagrams

Each homemade children's house differs in size. Based on how many “inhabitants” are planned in it. If the child plays alone, then 1.5 * 1.5 m is more than enough. If there are two children, larger sizes are already needed. At least 2*2 m. Decide for yourself on height too. But it’s better not to do less than 1.5 m.

House made of boards and plywood with a slide roof

It is also worth thinking about placing a house in which the baby can enjoy playing and constantly fantasize. You can make it from the most different materials that remain after repair or construction. If you live in an apartment, then you can always find a corner in it that can accommodate a small structure. Building a children's house with your own hands is not at all difficult. This will be discussed in the article.

Undoubtedly, the choice of materials for making a house is quite large. Almost everything is suitable for making a simple design. The most common types of gaming houses are:

wood;
cardboard;
fabric (like a wigwam);
plasterboard.

Since we are talking about a miniature house, it should be decorated according to all the rules. At a minimum, pillows, boxes of toys and a table should be placed here. If the place allows, and the parents’ imagination has no limits, then the resulting children’s home is decorated and decorated not only inside, but also outside. This will only add interest and intrigue the baby. If you want to make a site with a house in the country, it is worth considering the impact of atmospheric phenomena.

If the child is old enough (over one year old), then it is worth involving him in the process. This way, your baby will be able to learn simple skills and develop fine motor skills through play.

Before drawing up a drawing of the future building, you need to think through several main points, namely the type and type of house, as well as its dimensions. To do everything correctly, you need to define the following parameters:

Type: open or closed.
Dimensions: total area and height.
Placement: on the ground or on a tree.
Material for production.
Incorporation of windows and doors into the design.
Additional elements: extensions, fencing, slide, stairs, sandbox and others.
Interior design.

Also, when developing a building plan, you should consider a few more points:

mobility or stationarity;
the height of the doors should be at the ceiling;
exclude places of injury (corners and protruding nails);
The roof should not be flat so that a child cannot climb on it.

The drawn up diagram will allow you to assemble the structure exactly according to the specified parameters, which means the result will be excellent. If there is no time to develop a sketch, then you can use the ready-made drawings that are given in the article.

The windows and doors provided in the children's house must face the house so that parents can constantly monitor the child.

Since a wooden house is one of the most common for outdoor placement, we will consider it in more detail. The list of its advantages includes: practicality, strength, durability and safety, which is important. To make a children's house out of wood, you need to follow this stage of work.

First of all, you need to decide on the place on which the house will be built. This point is especially important when it comes to a permanent structure. Undoubtedly, every child's biggest dream is to have their own playhouse in a tree, but this, in turn, increases the possibility of injury, so we will focus on a hut built on the ground. If desired, it can be supplemented with other children's elements for the game.

When choosing a place, focus on an area where there will be shade after lunch. It will not be hot in such a house, and the child will be able to play throughout the day. Also, do not forget that there should be no obstacles nearby, since a child who is keen on playing will not notice flower beds, beds or building materials. This will also provide high level security.

Separate the children's play area with a low border, for example, made from car tires.

All dimensions are chosen arbitrarily depending on wishes and available material. If we are talking about a small playhouse, then the following dimensions will be sufficient:

width – 160 cm;
height – 150 cm.

At the first stage, the foundation is prepared. Despite the fact that we are talking about a simple structure, in order for it to last at least 5 years, it is worth considering the presence of an elementary foundation layer. So, as a base, it will be enough to fill the site with a small layer of crushed stone or compact the soil well with the addition of sand.

When decorating the floor of the house, you can choose one of the common options:

Support beams are laid on the prepared and compacted base and the floor is covered.
Supports from cellular concrete placed only at the corners of the house. The prepared floor frame is fixed only at the corners.

Don't forget about this important point, as waterproofing, which can be a simple roofing material. Special mastics are also suitable, if any remain after construction. This stage will extend the life of the playhouse.

The base of the floor will be simple wooden boards 3 cm thick. They are connected into a rectangular box and fixed with metal corners, which will add strength. For greater reliability, experts recommend installing additional cross bars. MDF or chipboard sheets will serve as finishing material, you can even use wooden boards. After the floor is ready, it is necessary to treat it with protective agents (antiseptics) and paint it.

The presence of a small gap will allow air to circulate well and ventilate the house after rain or winter.

To build the walls of the playhouse, it will be quite enough to use the beams from which the frame is mounted. After this, it is sewn up with clapboard or the same shields. During the installation process, do not forget about windows and doors:

Installed in all corners wooden beams with a cross section of 6x4 cm and the required length (depending on the height of the building).
Installation of beams under doors and windows. Nails or special corners can act as fasteners.
Installation of additional spacers between the rafters (half height). This will add more strength to the base.
Horizontal beams for windows and doors are prepared in advance: they cut off the required length (the calculation is made depending on the width of the cladding material).
For the roof frame, you need to take two bars and knock them together into a corner (the shape of an incomplete triangle, the wall will serve as the base). The free ends are reinforced on the upper beams of the walls. Depending on the size of the house, from 2 to 4 pieces of such triangles are prepared.

When installing the roof frame, first secure the front and rear element, and after that the middle parts are placed.

Now you can begin to directly cover the frame of the playhouse. Common materials in this case are:

lining;
shields;
boards.

In the case of lining, the process is much simpler, since there is no need to adjust all the elements to the specified dimensions. They also connect easily to each other. In this case, the roof is closed edged boards, and is protected by roofing felt. If there are tiles or ondulin left, then they will do. Everything will depend on your imagination and capabilities.

Here is a real and full-fledged playhouse. The finishing touch is design and decoration. How to do this? This will also completely depend on the available materials and desire. It is enough to be guided simple tips and recommendations:

paint the building in bright and colorful colors;
involve children in work;
You can buy appropriate fittings for doors and windows;
A table and chairs are installed inside, which are also pre-painted.

Always remember safety. Everything that is inside the playhouse and the structure itself should not have sharp elements.

A simpler design is the structure made of simple sheets plywood. But, despite its simplicity, such a house will delight every child and allow him to expand his imagination for games every day. This type of construction has a lot of advantages, but the main thing is that it requires a minimum of time and effort.

As in the previous case, a plywood house should first be sketched on a piece of paper in order to know the exact result. Consider the scale and calculate required amount materials. The construction site is cleared and leveled.

You should also collect all the tools that will be needed during construction:

stationery knife;
hacksaw;
hammer;
sandpaper;
jigsaw;
roulette;
pencil;
brushes and rollers;
screwdriver

The list of materials must include:

Sheets of plywood 8-12 mm thick.
Wooden beam with a section of 5×5 cm.
Soft tiles.
Plexiglas for windows.
Glazing beads.
Fasteners: nails and screws (give preference to stainless steel elements).
Hinges for doors and window shutters (if provided).
Paints and varnishes.

You should also take care of the funds in advance personal protection: gloves, work clothes, goggles and respirator.

Using a hacksaw, the timber is cut into pieces for mounting the frame. All elements are cleaned sandpaper and treated with antiseptics against fungus.

We cut sheets of plywood using a saw or electric jigsaw to the elements according to the existing diagram. To maintain accuracy, we use a tape measure. Edges are also trimmed and processed. protective compounds. During the work there will be a lot of dust, which is removed with a vacuum cleaner.
We select a place. The site must be absolutely dry, without tall vegetation around. It is ideal if there is a specially designated children's area, where a sandbox, slide and swing are already equipped.
We clear the selected area of grass by removing upper layer soil. A layer of sand or expanded clay is poured and compacted. For convenience, limiters are placed in the form of wooden boards. Rubber or foam can serve as a water barrier. In order to completely limit the contact of the house with water, it is recommended to provide for the construction of a support.
There should also be no difficulties in building the frame. In the process, the width of the plywood elements is taken into account. A frame is built with a certain pitch for the beams. Since the house is summer, there is no question of insulation.
Once the frame of the house is ready, you can move on to arranging the roof. A gable shape with a slope that a child cannot climb is best suited. Flat roof it is much easier and faster to do, but in this case the baby may be injured if he decides to climb on it.
The roof frame is also made of beams, after which the sheathing is filled (the pitch corresponds to the width of the plywood sheet). When everything is ready, you should treat the surface with protective agents against rain and snow. Among the great variety roofing materials it is best to give preference soft models, which do not highlight harmful substances and are not dangerous.
Sheathing the frame is carried out using a screwdriver or a hammer. In the latter option, it is necessary to carefully ensure that the ends of the nails do not come out and cause injury to the child. If this happens, then you need to grind them off with a file. All cracks and holes are sealed with polyurethane foam to avoid drafts.
Before painting, the playhouse is carefully primed. You can paint using any of the methods you prefer. Posters with images of children's favorite heroes will complement the decoration.

When developing a drawing, it is worth taking into account the age and height of the child. The first indicator will set the theme of the gaming house, and the second - the dimensions.

Do not forget that the final stage of the arrangement will be the installation of windows and fixing of doors. Windows are cut out of plexiglass in accordance with the window opening. They are fixed with glazing beads and small nails. For greater strength and reliability, the edges should be treated with sealant. Will complement the picture beautiful trims, which will give more comfort.

There is no need for a massive door in a playhouse. In most models it is completely absent, but for a greater sense of usefulness it is worth providing for them. Only 1 layer of plywood is suitable for it, which is reinforced with transverse dies. Fixed on door hinges and painted.

A house on supports provides for a staircase or a small threshold. Its width should correspond to the doorway. The steps should be wide so as not to fall during active play.

Any children's building will not be difficult for a person who knows how to use a hammer. It is enough to pick the correct scheme or compose it yourself, and then strictly follow the specified parameters and data. Don’t limit your imagination, and also involve your baby, who will tell you what and how will be more convenient for him in his own playhouse.

Video

This video shows an example of how you can make a wooden house for a child:

Photo instructions

The photo instructions we offer show you step by step how to make a playhouse:

Photo

Ideas different types houses for children:

Scheme

These diagrams show how to make calculations for a children's house, which will allow you to quickly think through your project:

As children, each of us tried to build a separate home for ourselves - toy house. Despite the simplicity of the design, it was the best shelter for games

The shaky structure made of boxes, cardboard or branches in the form of a hut bore the proud name of a house and seemed to be the best.

As we grow older, we think about creating a more durable and functional house for children.

Most often, a children's playhouse is built from wood. The choice of material for the house is determined by rational considerations - wood is an environmentally friendly and durable material. Small house made from coniferous species tree will have a positive effect on the child’s health. In addition, it will give the child the opportunity to feel independent. By building a full-fledged educational house for your baby, you will provide him with his own play area where he can play in any weather.

For parents, the main thing is that it is safe, inexpensive and fits into general style country house or suburban area. Another advantage of the house is that if it is not needed, it can be used as an outbuilding, so to speak, a beautiful storage shed gardening tools, unnecessary things or firewood.

How to make a children's house out of wood

This article will describe step-by-step instruction How to build a children's wooden house with your own hands.

1. Children's playhouse ideas

First, think about what the house will look like, what type, appearance and dimensions it will be. To do this you need to define:

Type. Open or closed;
Dimensions. Occupied area and height;
Installation location/location. A house installed on the ground and on a tree has different principle structural device;
The material from which the building will be made;
Availability of windows, doors and materials for them;
The presence of additional components - extensions, a fence (fencing), a terrace, a slide, a sandbox, a swing, a ladder.
Availability of interior finishing.

Pictures of a house for children

The photo below shows how to make a children's wigwam for Indians, a hut for Robinsons and a yurt for nomads from wood, fabric, branches and bushes.

Hut for fairy-tale heroes and forest dwellers.

A pirate frigate for young robbers and a sailing schooner for cheerful sailors.

When developing a house plan, it is worth considering the following:

mobility or stationarity. The size of the house and the technology of its construction will depend on this;

The presence of at least two windows is mandatory. Firstly, this is lighting. Secondly, the hut must be clearly visible for control;

the height of the windows from the floor should be 500-600 mm;

door height. At 200-300 mm. taller than the child's height. But it’s better to make them under the ceiling, because sooner or later you will be invited to the house;

walls. Must be smooth to eliminate the possibility of injury;

roof. Under no circumstances should it be flat. So as not to attract the child to climb on it.

You can sketch your own sketch or use ready-made drawings. Below, schematic drawings show projects of children's houses that you can build with your own hands.

A diagram of a children's house with all the indicated dimensions will help to correctly prepare materials for construction.

3. Tools and material for manufacturing

Tool:

hacksaw;
plane;
roulette;
chisel;
metal corner;
building level;
drill;
screwdriver or hammer and nails;
sandpaper (for sanding wood);
brushes and paint for painting a house or any finishing material type of lining or siding.

Material:

timber for making a frame. Recommended section 50x50;
lumber for sheathing. Boards or timber will allow you to create a beautiful house;
plywood (thickness at least 8 mm) or OSB for cladding. Cheaper, but also less durable material that requires additional processing;
roofing material;
brick;
glass for windows (if necessary and only for children over 7 years old, and even then in doubt - it is better to exclude any presence of glass).

4. Construction of a wooden children's house with your own hands

4.1 Foundation

Of course, you shouldn’t pour a strong foundation for a children’s playhouse made of wood. But take out the soil to a depth of 80-100 mm. and laying bricks over the entire area of the building does not fit. This way the hut will last much longer.

Alternatively it can be used terrace board. But its acquisition is very expensive.

The most affordable and quick option- make a foundation of several bricks and a timber frame installed on it. This approach to foundation construction is usually used in greenhouse farming.

4.2 Floor for the house

It is better to equip the floor according to all the rules of the genre. Namely, lay the logs and stuff them floorboard. Or lay OSB or plywood in two layers, so that the next layer overlaps the seams of the previous one.

4.3 Walls and frame of the children's house

Holes are dug at the corners of the foundation to install timber. This is a wall support. Before placing the timber in the ground, it must be processed. Additionally, timber is also installed in the installation areas of windows and doors. For rigidity, the frame bars can be fastened together with a metal corner. Next, the frame is covered with boards or plywood.

A wooden children's house, the drawing of which is given below, can only be built with the installation of supports.

For an ordinary house, there is a simpler option - knock down shields from boards. And fill timber around their perimeter. Then knock the wooden panels together.

Material prepared for the website www.site

4.4 Roof for a children's playhouse

The construction of the roof begins with the manufacture of gables. The same timber is used for them as for the frame. Two triangles are installed on opposite walls. If necessary, several more are installed between them.

A beam is placed between them. One or more depends on what the roof will be covered with.

Or we knock them into a shield, which will then be attached to the gables.

The essence is the same, the difference is in ease of use. One slope or two, the main thing is that the roof is not used by the child as a playground. If the boards fit well, it is enough to treat them with an antiseptic and paint them.

5. Decorating a children's house made of wood

In order for a handmade wooden house for children to please you, you need to take care of protecting the wood for as long as possible. To do this, it needs to be treated with solutions against bugs and rot. And then open it with stain, varnish or paint.

Install benches inside the house or make a table and chairs of appropriate sizes.

6. Safety of the children's playhouse

Separately, I would like to focus on how to make the house safe. To do this you need:

choose a flat area to install the house. Or a reliable tree;

check the quality of wood processing. Mechanical to prevent splinters from entering. And antiseptic - the wood must be environmentally friendly;

screw screws correctly;

better to use for roofing soft materials or polycarbonate. Because, for example, metal tiles have sharp edges and can cause injury.

Tree house for children

If you have already grown up from a small children’s house on the ground, then it’s time to move higher, for example, to the crown of a tree (canopy, uvei, i.e. the upper/middle branchy part of the tree). Additionally, we will describe how to make a tree house for children with your own hands.

1. Choosing a tree

Pay attention to the tree's crown, trunk, location of branches, age of the tree and its size. Coniferous trees are not very suitable for this type of construction, since the needles transmit little light.

In addition, it is important to remember that as the tree grows, it will change its shape. Therefore, build on the lower branches or try to take this fact into account.

2. Selecting a design option (shape)

We need to work out the idea, again, taking into account the configuration of the tree.

A schematic image with dimensions will help you develop your project and imagine what the finished product will look like.

4. House installation

All work on the construction of the walls and roof of the house is best done on the ground. But, the installation of floor support belongs to the category of high-altitude work.

To make a floor in a house on branches, you need to install a platform, which will be the basis of the entire structure. It can be supported by additional supports installed on the ground, or by supports installed on the tree trunk.

Fixing the platform on the trunk will allow you to adjust its height over time.

5. Finishing work

Installing a ladder is a mandatory step in building a tree house. The ladder can be wooden or rope. The first one is more reliable. In addition to the ladder for the house, you can attach a rope along which the descent will be faster.

6. Security

a comfortable staircase (straight, spiral), preferably with railings;
optimal height of the house. Preferably, up to 3 meters;
a reliable platform, necessarily enclosed by walls or handrails;
The technology for building a children's wooden treehouse does not involve connecting with nails. It is safer to use bolts and nuts;
In addition, the wood and all connections of the house must be periodically checked and tightened.

Conclusion

As you can see, making a wooden house for children with your own hands is not difficult. In fact, using the same principle of modules, wooden houses for the playground are made, and even cardboard houses for playing in the apartment.

Wooden children's houses - photos and pictures for ideas

Sections