Motor filter for a vacuum cleaner - an overview of frequently asked questions. Simple ways to make a filter for a vacuum cleaner with your own hands How to replace the filter in a Samsung vacuum cleaner

Most modern vacuum cleaners are equipped with various types of filters, the purpose of which is to trap even the finest dust inside the device and remove it outside. fresh air. Consumers are often interested in how to make a filter for a vacuum cleaner with their own hands. There can be many reasons for this: high cost Supplies(bags, HEPA filters), their absence for sale, the desire to modify the device and adapt it to collect dust during repairs or construction work. The simplest but most effective ways to make various filter elements are in the material below.

Types and purpose of filters in a vacuum cleaner

The following types of filters are found in modern vacuum cleaners:

• HEPA;
• dust bag;
• water;
• cyclonic

(or fine filters) are used in many models of vacuum cleaners, be they Samsung, LG, Thomas, Karcher or another brand. Their advantage lies in high-quality dust retention. The air flow passes through these elements at the outlet of the vacuum cleaner and leaves the smallest particles of debris that the bag, cyclone container or aquafilter could not contain. Most often, to make your own HEPA filters, you use a cabin filter for a car, for example, the UAZ brand.

Dust collectors used in bag-type devices as a container for collecting collected waste. They reliably and effectively capture even small dust particles. Their disadvantage is that when the container is filled, the power of the device gradually decreases, and the bags themselves have to be constantly purchased.

On a note! There are also reusable dust bags, but they need to be shaken out regularly, while being in contact with dust, which is not very convenient and unhygienic.

Vacuum cleaners with water filter(aquafilter) are considered the most effective solution. In them, the air flow passes through the liquid, leaving in it not only debris, but also the smallest particles of dust, allergens and pollen. Such devices are great for people with allergies and families with small children. To ensure maximum efficiency, additional filters must be installed in the vacuum cleaner in addition to the water flask. They are needed to stop debris that is not retained by water, such as plastic shavings.

Devices with cyclone filter are highly popular. The principle of their operation is based on the influence of centrifugal force. The air flow enters the container and moves inside it, as a result of which large debris settles to the bottom of the container, and small debris is retained by an auxiliary filter, usually a foam filter. Next, the container is emptied and, if necessary, washed.

On a note! In cyclone devices, it is periodically necessary to replace the sponge when cleaning and washing do not help restore its properties.

Required tools and materials

Homemade consumables are usually made from the most simple materials, which can be found in every home. Most often they are made made of high-density foam rubber or non-woven fabric. Even if such material is not at hand, it is always freely available for sale. In addition, for the manufacture of filtration elements the following are used:

• padding polyester;
• non-woven napkins;
• felt fabric;
• denim;
• materials for automobile filters;
• medical bandages and other supplies.

The choice of one of the above materials depends on the type of filter. But there is one thing important condition, which must be observed when selecting a base for creating a consumable part, is the correct density. The material must allow liquid to pass through, but at the same time reliably retain even the smallest dust.

For the manufacture of water and cyclone filters require more materials. First of all, a container is selected (bucket, tank, pan, bottle, etc.), and then the rest of the components: pieces plumbing pipe, corrugated hose, fasteners, silicone sealant, etc., depending on the method of manufacturing the part.

On a note! Tools for making filters of any type can be found in every home. These are scissors, a stationery knife, glue gun, drill, stapler, screwdrivers, etc. No special equipment is required for this.

Making filters step by step

Today, craftsmen have come up with many ways to create filters. different types with your own hands. There are a large number of videos and training instructions on this topic on the Internet. Make the right thing It won’t be difficult if you select the necessary material and follow the specified procedure.

The principle of operation of the cyclone filter is based on centrifugal force, due to which, during air movement, debris is separated and settles to the bottom of the container. For the manufacture of simplest design required:

• car oil filter that retains fine dust;
• 20-liter bucket with a tight-fitting lid;
• polypropylene elbow with angles of 45° and 90°;
• 1 meter of plumbing pipe;
• 2 meters of corrugated tube.

The manufacturing process is as follows. A hole is made in the lid of the bucket and a 90° corner is installed - the vacuum cleaner will be connected here. The cracks must be securely closed silicone sealant. Next, a second hole is made on the side of the bucket wall and a corner is fixed at 45° - a corrugation with a dust collection tube is connected here. WITH inside The lid is secured with a holder onto which the filter is tightly placed. It must be pressed firmly against the lid, otherwise dust will enter the vacuum cleaner through the cracks.

Advice! To protect the filter with the holder, you can put a nylon stocking on it - this will prevent the ingress of small dust particles. And to protect it from damage by large solid debris, you can additionally build a galvanized casing.

At the final stage, the elbow in the lid is connected to the filter outlet. If difficulties arise at this stage, you can use rubber hose. The joints will need to be treated with sealant.

Operating principle of the design looks in the following way. The garbage, along with the air, is drawn inside the bucket, while large particles, due to centrifugal force, are separated and settle to the bottom of the container, and small particles are retained by stockings and a filter. The dust that was able to overcome these obstacles ends up in the vacuum cleaner bag.

Water

You can make a simple aqua filter from old pan and 5 liter plastic bottle for water. The principle of its operation is that the air coming out of the vacuum cleaner, through a metal adapter and a flexible corrugated hose, enters a bottle of water, where it is cleaned of the smallest dust particles and moistened, and then released into the room. To make such a device, in addition to aluminum pan with the bottle you will need a metal adapter for a corrugated hose, a drill, screwdrivers, and self-tapping screws.

Advice! If the vacuum cleaner is old and low-power, you can additionally remove the filters inside and replace them with foam rubber - this will slightly increase the suction power of the device.

The manufacturing process looks like this. You need to cut out the bottom of the pan to reduce its weight, and then drill three holes in it. Two are made in the handle, one in the side wall under it. Next, the pan is attached with self-tapping screws to the back of the vacuum cleaner, where there is a holder for the brush. You need to make several holes around the neck of the bottle to allow air to escape. Next, the container is placed in a saucepan, after which approximately 0.5 liters of water is poured into it. The next step is to install instead of the exhaust filter of the vacuum cleaner and the cover that covers it. metal plate with an adapter for a corrugated hose and attached to the body with self-tapping screws. A hose is put on top, secured with a clamp, and its other end is lowered into a bottle of water.

Now the operation scheme will look like this - air enters the vacuum cleaner through the hose, large debris remains in the bag (cyclone filter), and small debris moves further along with the air flow, leaves the cleaning device and falls into a container of water, where it remains in the liquid. And purified and humidified air enters the room.

NERA

HEPA filter elements are usually installed at the outlet of the vacuum cleaner for cleaning air flow from remaining dust microparticles. Inexpensive parts of this type have a limited service life and must be periodically replaced with new ones, while higher-quality models can be washed, but over time they also fail, after which the purchase of a new filter is required.

On a note! A HEPA filter is usually quite expensive and is not always on sale. For vacuum cleaners famous manufacturers it can be ordered at a service center, but for little-known brands this is not possible.

The fine filter can be made from old, clogged with dust, and a car cabin filter a, the price of which is much cheaper than new original accessory. To do this, you first need to remove the old filter from the housing using a knife, and thoroughly clean the inner surface of any glue residue and degrease it. From car filter you should cut a new one exactly to size, place it inside the case, glue it and fill it with silicone sealant. It is necessary to ensure that there are no gaps, holes or voids left between the housing and the material, otherwise it will negative side will affect the efficiency of air purification. Next, you need to leave the part until completely dry, after which it can be placed in a vacuum cleaner and begin cleaning.

Dust bag

Buying disposable paper bags for vacuum cleaners is expensive, and if the equipment is produced by a little-known company, it will be very difficult to find them. A permanent fabric bag fails over time. To replace it, you can make a new dust collector with your own hands from high-density fabric.

Advice! Spunbond, a covering gardening material, is very suitable for a fabric dust collection bag. It's cheap and sold everywhere.

The production process is quite simple. The purchased piece of fabric needs to be folded in two or three times, depending on the density of the material, and then a pattern is made from it. The required dimensions can be taken from an old bag or obtained by opening the lid of the vacuum cleaner and measuring the length and width seat under the dust collector. For example, if a piece of fabric is folded in half, and you need to make a bag with sides of 30 cm from it, then you need to cut the piece in the shape of a rectangle with sides of 62 and 32 cm (1 centimeter on each side is added to the hem). Now you need to fold the workpiece in half, bend the edges and firmly fasten it with a stapler. And to make a reliable reusable bag, the edges need to be stitched sewing machine, and on one side sew a zipper or install Velcro tapes.

The next step is to make the hole. To do this, remove the plastic or cardboard base from the old bag, attach it to the middle of the dust collector, draw a hole and cut it out. If the bag is reusable, you can attach an old holder to it. Otherwise, you need to cut out a base of similar size from paper (very thick) or cardboard and glue it to the bag, aligning it with the hole.

Pros and cons of homemade filters

The main advantage of self-made filters is saving money on replacing them, as well as time, which can be spent on searching and purchasing consumables. In some cases, you won’t need to buy anything extra to make filter elements, because the necessary components can be found at home.

In addition, homemade filters significantly expand the capabilities of technology. They improve the quality of cleaning, and sometimes even allow you to carry out not only dry, but wet cleaning of the room. According to their own technical properties such details are absolutely not inferior to the originals, and sometimes even surpass them.

However, when using home-made filter elements, it is important to remember that their installation is in some cases unacceptable. You need to know this if the vacuum cleaner is under warranty service. IN in this case upon detection of non-original parts service center will refuse the user a free repair.

Important! Before installing a homemade filter, you need to make sure that it does not increase the load on the device and energy consumption.

So, make homemade filter at home it won’t be difficult if you know the action plan, have necessary materials and free time. This will save money, time searching for consumables, and also significantly improve the capabilities of the vacuum cleaner.

The best vacuum cleaners

Vacuum cleaner Thomas Aqua Pet & Family on Yandex Market

Vacuum cleaner Samsung VC20M251AWB on Yandex Market

Vacuum cleaner Thomas DryBOX+AquaBOX Cat & Dog on Yandex Market

Vacuum cleaner Thomas Perfect Air Feel Fresh on Yandex Market

Vacuum cleaner Miele SBAD0 on Yandex Market

Vacuum cleaner - necessary thing in every house. Many people think about the question of how to make a filter for a vacuum cleaner with their own hands. It is already difficult for any housewife to imagine cleaning without using this device. The machines do an excellent job of removing accumulated dirt, and some models also help with wet cleaning.

An important part of a vacuum cleaner is the filters, which are responsible for retaining and collecting debris and dust. Like any thing, they tend to wear out, so every owner of such a device can decide to make a filter with their own hands. Modern models use different types of them - from ordinary bags to specialized ones with additional functions.

Some you can try to make at home. This will cost less than buying a ready-made filter in a store, and will last much longer.

There are several types of such collections:

How to make a water filter for a vacuum cleaner

More often it is called an aqua filter. Nowadays such models are popular in the market household appliances. Their secret is that they not only collect garbage, but also humidify the air without causing unpleasant odors. The only negative is the large weight of the vacuum cleaner due to the vessel with water inside, but it is compensated for good quality cleaning

The principle of its operation is very simple. With the help of a motor, all debris ends up in a compartment with water, which then needs to be drained.

How to make this type of filter? It’s quite simple if you have all the necessary parts and a work plan.

You will need a separator, water container, fan and pump. The smaller the fan you choose, the less noise it will make. When choosing a pump, keep in mind that the water level in the vessel will rise by almost a centimeter. Choose all fasteners with zinc coating. Don't forget about the built-in turbo brush, it will help thoroughly clean carpets. To get a good result, carry out the work in stages:

1. Install the dust collector casing, storage tank and disintegrant.
2. Attach the pump with a rubber ring. Watch the gaps between the housing parts.
3. To make the vacuum cleaner as silent as possible, stick polyethylene on the bottom.
4. Before use, pour water strictly according to the marks on the container.

There are other ways to create an aqua filter. Maximum effort and desire - and you will do it quality work, which will be beneficial for a long time.

DIY cyclone filter for vacuum cleaner

The cyclone filter has remained popular for over 30 years. The advantage is the absence of dust bags, while it is almost silent and compact. It is also much lighter than its “aquatic” counterparts. But the downside is that cleaning such a filter is quite difficult.

This model is used both for cleaning the house and in construction. Sawdust, shavings, and large debris will not be a problem for the device. The secret of power lies in the way it works.

Dirt, under the influence of centrifugal force, begins to move in a spiral, which causes large debris to fall into the outer chamber, and small debris to remain inside. As a result, the vacuum cleaner will not pollute the air.

There are 2 ways to assemble a cyclone filter.

Assembly method No. 1

You will need:

• plumbing pipe - 1 m;
• five-liter bucket with a tight lid;
• polypropylene elbow (angles 45 and 90 degrees) for creating brackets;
• corrugated pipe - 2 m;
• nylon stocking;
• sealing glue;
• plywood.

Completing of the work.

Attach a bracket (made from steel strips) for the air filter to the lid of the bucket. Make sure that its connection is tight so that contaminated air does not penetrate into the outlet pipe in the future.

Attach the outlet tube firmly to the top. The air flow will pass through it into the vacuum cleaner. Leave the membrane from the vacuum cleaner, this will help save the fan from severe contamination. Place a debris trap around the filter (made from galvanized sheet metal). Pull the nylon stocking, it will protect against small debris. Next, place the corrugated tube along the side wall and tilt it towards the bottom. Reinforce the walls of the bucket with steel strip.

Tip: use a bucket instead plastic barrel or a tin vessel.

Use sealing adhesive on all seams.

Assembly method No. 2

You will need:

• traffic cone(can be purchased at a car store);
• dense plastic container with a sealed lid;
• 2 corrugated pipes - 2 m each;
• nuts and washers - 8-10 mm;
• 2 rods (length - 2 m, width - 8 mm).

Completing of the work.

As a container for collecting dust, we use a plastic jar with thick walls and a tight lid. This is important to ensure that there are no leaks, which can subsequently adversely affect the performance of the vacuum cleaner.

Cut off the bottom of the traffic cone and cut out a plywood cover in the hole. We insert it into it corrugated pipe(you can use a regular plastic one), which should be lowered to the middle of the cone, otherwise a lot of debris will get into it.

We install the upper part of the cone tightly into a plywood circle connected to the lid of the garbage container. We attach a pipe to the upper cut, into which air with dust and dirt will enter.

Let's move on to connecting the filter to the vacuum cleaner.

We connect the outlet pipe to the inlet of the vacuum cleaner with a hose, and attach a hose that collects debris to the intake pipe.

Tip: If you can't find a traffic cone, make your own by cutting it out of sheet metal or an old galvanized bucket. Instead of a cone shape, you can use a cylinder (polyethylene pipe).

By spending a couple of evenings and a little effort, you can turn your regular vacuum cleaner into a more modern version, thereby providing your household with reliable devices and making life easier for the owner of the house. If desired, the device can have more than one filter. The main thing is to use materials that do not require large expenditures and follow the instructions given. In any case, if it doesn’t work out the first time, it will definitely work out the second time.

Today the market for household appliances is full modern models vacuum cleaners equipped with various filters. Their main purpose is high-quality air filtration by retaining the smallest dust particles. However, the high cost of consumables, as well as the desire to modify their vacuum cleaner, often lead to a question among consumers: how to make a filter for a vacuum cleaner with your own hands at home. There are many in various ways manufacturing filter elements, the main advantage of which is their availability. After all, all the necessary materials and tools can usually be found at home or purchased at any hardware store at low prices.

What can a filter for a vacuum cleaner be made from?

When creating filters, use various materials, which are easy to purchase at any hardware store. A common option is foam rubber. But you can also use any dense non-woven fabric. The main thing you should pay attention to is the density of the composition. The material should pass water easily enough and at the same time retain the smallest dust.

Foam filter

If the filtration element becomes dirty, you can replace it yourself in order to avoid spending money on buying a new one. To do this, you will need a piece of new foam rubber of the required thickness, or you can also use a dishwashing sponge. At the same time, if you buy material, you can buy foam rubber of different densities (the layer with a higher density will go first to the filter inlet). Cut using scissors right size and the same scissors are used to adjust the thickness, after which the new filter is installed in the vacuum cleaner.

Filter made from other materials

Process self-creation air filter involves the use of other materials. Foam rubber can be replaced with fabrics of the same density.

The manufacturing principle is the same as in the case of using foam rubber: using scissors or a stationery knife, a filter of the required size is cut out of the material.

DIY water filter

Water filters (or aquafilters) refer to effective ways cleaning. Along with high dust removal rates, this system also allows for air humidification.

The aquafilter works according to to the following principle: air, together with dust particles, enters a container with water where, under the influence of gravity, the entire suspension settles to the bottom of the filter, and the purified and wet air the flow moves further through the device and flows out. The device also has disadvantages:

• large weight of the structure due to the additional mass of water;
• increased noise when the vacuum cleaner is operating.

Materials for production

To make an aqua filter, you only need a drill, self-tapping screws and a screwdriver from the tools. The main materials will be:

• aluminum pan;
• 5 liter plastic bottle;
• hose;
• metal adapter.

Build process new system filtering consists of several steps:

Making a filter for a Samsung vacuum cleaner with your own hands

Many vacuum cleaners Samsung brand equipped with HEPA output filters, which are known for their ability to capture even microscopic dust particles and provide high-quality air purification. However, filter elements in this category have a significant drawback - the need for frequent replacement, as well as a fairly high price. That is why they are often made independently.

Materials for production

To construct a new HEPA filter with your own hands, all you need is a utility knife. The list of materials will include a cabin filter for cars with the same accordion height as the original filter in the vacuum cleaner. Also during the work, sealant and acetone will be used for degreasing. The manufacture of a cleaning system involves several stages:

1. Using a utility knife, cut out the dirty filter from the cassette.
2. The cabin filter is disassembled and the filter material is removed. Squeezing the accordion tightly, cut out the filter, the size of which should be 1 mm smaller internal size cassette.
3. A layer of sealant is applied around the perimeter of the compressed cabin filter.
4. The inside of the HEPA filter cassette is first degreased with acetone and also covered with a layer of sealant (layer thickness should be about 3 mm).
5. The filter element is installed in a plastic shell and then dries for 1 hour.

Membrane filter

Filters of this type are used in many professional models of vacuum cleaners that do not have garbage collection bags. The main purpose of the membrane is to additionally purify the air flow before it enters the HEPA filter (to the last filtration section). Additionally, the membrane protects the entire device, preventing dust particles from entering the system and clogging other filters.

Materials for production

In order to make your own membrane filter, you will need a piece of dense material, which can always be purchased at a hardware store. In this case, it is necessary to take measurements in advance from the original dust collector, which requires replacement.

The density of the fabric can be increased by folding the fabric into several layers. Thick cardboard or plastic can be used as a base for the membrane bag. You can attach the filter to the base using one of the following methods:

• using glue that fixes the neck of the bag between two pieces of cardboard;
• using Velcro - in this case, you will need to first glue one part of the Velcro to the base, and sew the second to the bag itself.

Cyclone filter

The design of cyclone filters makes them much more convenient and efficient than conventional garbage disposals. Due to their spaciousness and hygiene, such purification systems are becoming increasingly popular. However, not everyone can afford the high cost.

The principle of operation is as follows: the air flow passes through primary filters, which trap small dust particles. Next, the air enters the cyclone filter - a container in which, under the influence of the vortex effect, larger particles of debris swirl and settle to the bottom under their own weight. At the outlet, the air is 98% purified.

Materials for production

The simplest way to make a cyclone filter is to use a plastic bucket as the main element. The volume is calculated quite simply. For every 100 W of power, add 1 liter of capacity.

Expert opinion

Nikolai Petrovich

Subpage for an expert

A mandatory requirement for the container is the presence of a hermetically sealed lid.

In order to design a cyclone system filter, you will need the following tools:

• stationery knife;
• glue gun;
• silicone;
• compass.

Materials you will need:

• container with a lid (you can use paint or building mixture buckets);
• 45° elbow - 2 pcs.;
• 90° elbow - 2 pcs.;
• O-rings;
• plastic pipe.

The manufacturing process is carried out as follows:

Aqua filter for vacuum cleaner

Water filtration systems are perhaps the most popular among users. However, the price of vacuum cleaners equipped in a similar way purification is often too high. Therefore, there are many options for homemade aqua filters. Below is another example.

Materials for production

To construct a homemade aqua filter you will need:

• 10 liter PVC bucket with lid;
• plumbing adapters (3 pcs.);
• PVC panel;
• corrugated pipe for air flow outlet.

Two holes are cut out on one side of the bucket, the diameter of which is equal to diameters pipes. The walls of the holes are lubricated with silicone. An elbow is inserted into one of them and another pipe attached to it so that its end is located right near the bottom of the container (a gap of no more than 2 cm) - this part will act as an inlet for air flow. An additional cover with a hole for the pipe and a slot for air outlet is pre-cut from PVC, after which it is installed in a bucket (with a slight slope).

Another pipe is installed in the second hole, located above the membrane, to which a hose for the vacuum cleaner will be connected in the future. Before work, about 2–2.5 liters of water are poured into the container.

pros

Homemade filtration systems have a large number of undoubted advantages, namely:

• save time and money;
• expand the functionality of the vacuum cleaner;
• improve the quality of cleaning;
• have high quality, which is in no way inferior to the quality of factory elements.

Minuses

Getting started self-production filters, you need to take into account some nuances:

• The first of these is the prohibition of installation during the period when the device is under warranty. This can be explained by the fact that in the event of a vacuum cleaner failure, the free maintenance and repair service will not apply to those units of equipment that are equipped with any non-original spare parts.
• You also need to take into account the need for at least minimal skills in the manufacture and assembly of structures of increased complexity.

Would you make a filter for a vacuum cleaner yourself?

YesNo

Thanks to a large number various options, making filters with your own hands is available to every user. This approach not only allows you to significantly save money and time on purchasing new elements, but also significantly improves the quality of air purification even on those models of vacuum cleaners that have conventional air filters.

Tags: How can you replace the filter in a vacuum cleaner?

new filters here Subscribe to our...

Frequently asked questions and answers | Topic author: Ingrith

This topic presents questions that our clients have already asked, as well as immediate answers to them. Perhaps you have already had similar questions and this topic will be useful to you

THOMAS (Yeardley)  I read in the Thomas product catalog that the “Bi-Turbo” system is installed, what is it and what advantages does it provide?
Answer:
To save energy and increase the suction power of the vacuum cleaner, unlike most models on the market, a two-stage turbine is installed, i.e. with two impellers on one shaft, which increases suction power by 25-30%

THOMAS (Yeardley)  What cleaning concentrates are used for THOMAS vacuum cleaners
Answer:
4 types of cleaning concentrates are used: ProTex - for textile coverings and padded furniture; ProTex-V - for heavily soiled textile coverings; ProTex-M - for the destruction of textile mites; ProFloor - for linoleum, tiles.

THOMAS (Yeardley)  What is the best way to clean pipes and hoses after washing carpets?
Answer:
Empty the container dirty water, pour into a basin clean water, in a volume less than the dirty water capacity in your vacuum cleaner, turn on the suction and suck all the clean water into the vacuum cleaner, then pour it out. Can be repeated several times

THOMAS (Yeardley)  How high can the nozzles be raised when cleaning windows?
Answer:
The cleaning solution is supplied with a pressure of 4 bar (4 excess atmospheres), respectively, the height of the liquid rise will be about 40 meters, we hope that there will be no such high windows.

THOMAS (Yeardley)  We purchased a Thomas Twin vacuum cleaner, which attachment can be used to clean windows
Answer:
For cleaning windows in all washing vacuum cleaners THOMAS uses an adapter for hard surfaces, put on the nozzle for washing carpets, some models have an additional special nozzle

THOMAS (Yeardley)  What is the consumption of cleaning solution when cleaning carpets?
Answer:
It all depends on the degree of pollution carpets. For light wet cleaning, the consumption is approximately 1 liter of solution per 4-5 square meters. meters of coverage, with thorough washing of the carpet it can increase to 1 liter per 2 square meters. meters.

THOMAS (Yeardley)  What area of ​​carpet is enough for one liter of detergent concentrate?
Answer:
Depending on the degree of soiling of the carpet from 120 to 250 square meters

THOMAS (Yeardley)  When washing linoleum, water does not completely collect, please explain the reason
Answer:
Please note that the working part of the adapter for hard floors consists of a brush and an elastic band. When moving away from you, lower the pipe a little lower to the floor - the brush works; when moving towards you - on the contrary, lift it up, collecting water with an elastic band

THOMAS (Yeardley)  Recently purchased a SUPER 30 S vacuum cleaner, have already used the washing mode several times, the result exceeded all expectations, the carpets are like new. Today we decided to update the furniture, but the connecting hose of the nozzle turned out to be short, what’s the matter?
Answer:
When using the carpet cleaning attachment, stop valve is attached to the attachment (adapter) between the hose and the pipe. When cleaning furniture, it must be removed from there and inserted into the groove directly on the nozzle for washing furniture (it is narrower)

THOMAS (Yeardley)  What is the difference between the Thomas Twin XT and Thomas Vestfalia XT vacuum cleaner models?
Answer:
The Twin XT and Vestfalia XT models use the latest development of the Thomas company - Aqua-Box - for dry cleaning; wet cleaning allows you to clean carpets and floors hygienically and with high quality. If your home has parquet, we recommend the Twin XT model, as it is equipped with a nozzle for dry cleaning of parquet. This nozzle can be positioned parallel to the floor, which is convenient for cleaning under low furniture. And most importantly, it is equipped with a felt base and a pile made of natural horsehair, that is, it cleans efficiently and takes care of your parquet. And if you are the owner of a cat or dog, pay attention to the Vestfalia XT model. This vacuum cleaner comes with a large and convenient turbo brush for dry cleaning. The THOMAS TWIN XT model is available in blue color, THOMAS Vestfalia XT - in black.

THOMAS (Yeardley)  I accidentally forgot to pour water into the aquafilter and cleaned the whole apartment in dry mode. Is this very bad for a vacuum cleaner? What should I do now?
Answer:
The aquafilter cannot work without water. This means that all the garbage and all the dust that you collected in your apartment got inside the device without filtration. If you did not forget to install a HEPA filter, then it took the entire blow. And most likely you will have to replace it. You can try cleaning it as described in the instructions for your vacuum cleaner. Then put it on former place, assemble the device correctly, the aqua filter, pour 1 liter of water and turn it on. If the suction power has decreased, the filter will have to be replaced, that is, it was so dirty that cleaning did not help.

In addition to the bag, the vacuum cleaner has other filters. - BAGS FOR...

But besides the dust collector in any vacuum cleaner classical scheme there are others... However, the remaining filters can be replaced with simpler and...