Simple rabbit cages. DIY rabbit cages - simple and advanced designs

Breeding rabbits when properly managed can bring good dividends.

Animal cages must be made of high quality materials. The normal functioning of the animal depends on compliance with these requirements.

The main advantage of rabbits is their unpretentiousness. They have enough high stability to various diseases. A properly constructed home creates a comfortable existence for the animal.

Nursery construction

The correct drawings of cages for rabbits allow you to build a good home for the whole family.

The animal nursery consists of:

• frame;
• ceiling;
• side walls;
• central door;
• feeders.

How to make cages for rabbits with your own hands?

If the finished nursery is located on the street, then the height of the support should be 110 cm. High housing for rabbits helps protect animals from various predators.

The side walls are made of dense plywood or fine mesh. For feeding rabbits, it is recommended to use a fine mesh or thin slats.

The presence of holes allows you to get rid of food debris, thereby preventing their rapid spoilage.

The roof for the cages must be made of durable, waterproof material. Suitable for this: slate, roofing felt; polycarbonate

Materials for the production of housing should not contain sharp edges or chips.

Types of cells

Nursery designs have some differences among themselves.

Mainly:

• cells with queen cell;
• nursery using the technology of I. N. Mikhailov and N. I. Zolotukhin;
• a dwelling with an enclosure for walking animals.

The first version of the cage is a tall structure with two separate sections. One of them is used for feeding, and the other for the nest.

They are separated between thick sheet plywood. For normal movement of the animal, a manhole is provided.

An exit for animals is made in the side wall. The entire perimeter of the cage is fenced with a mesh. This helps prevent escape from the nursery area.

The sizes of cages for rabbits are calculated based on their number.

Note!

For intensive breeding of animals, the technique of combining neighboring nurseries is used. To do this, a corridor is made along the back of the cage with additional doors for the male to move around.

Industrial cell designs using Mikhailov technology

They are miniature farms. There is a nest for small rabbits, a place for feeding adult animals, and additional ventilation. An additional compartment for waste disposal is made along the lower border.

How to make a similar cage for rabbits? To do this, you need to familiarize yourself with the design drawings. The exact dimensions of the walls and ceiling are shown in detail here.

Nurseries using the Zolotukhin technique

Nurseries using the Zolotukhin technique are multi-storey departments that can accommodate several families. The design of the rabbit cage provides for additional compartments for feeding and easy cleaning of waste.

The main advantage of this method is to create conditions as close to natural as possible. Little rabbits acquire immunity to various viral diseases. The female independently arranges a warm nest from her down and dry straw.

Stages of cell creation

Making a simple animal cage is quite simple.

Note!

To do this, you must follow a strict sequence of actions:

• The frame of the future cage is assembled from the beams. The thickness should be 10 cm in diameter;
• a blank wall is installed in the back of the nursery;
• The sides of the cage are covered with mesh.

For this it is necessary to use small fractions.

• Experienced experts recommend upholstering the side walls with small slats. This will protect the animal from overheating in summer time and freezing in winter;
• The bottom of the nursery is made of a durable sheet of plywood;
• Feeders and additional doors are installed outside the cage. This allows you to easily remove bedding and debris from the animal.

The photo of the rabbit cage shows step by step instructions, which will facilitate the process of constructing a nursery.

Photos of do-it-yourself rabbit cages

Breeding rabbits suburban area or dacha requires a lot of knowledge about the lifestyle and habits of these animals. Much attention is paid to their diet and diet. At the same time, we should not forget about rabbit houses, since clean and comfortable housing is the key to the health and well-being of furry pets. There are many designs of cages for rabbits, made from a variety of materials with your own hands. Offered to your attention wooden structures can simplify the care of animals and will decorate the economic area.

Simple Design Rabbit Hutch

Due to the simplicity of the design, such a cage can be made with minimal experience in working with carpentry tools. To make it you will need wooden slats and bars, plywood, metal mesh, bitumen shingles and plexiglass. Despite the fact that this type of cage is not particularly complex, it looks beautiful and interesting, which all members of your family will appreciate.

Assembling the cage frame for rabbits

To facilitate the process of feeding animals, the cage is installed on an elevated surface, constructing an additional stand. The height is selected so that both adults and children can care for the animals. In order to have feed and hay at hand, and also not to look for additional space for storing food, the frame is equipped with a spacious shelf.

Cages for rabbits drawings

For support posts The cage will need a wooden beam with a cross-section of at least 60×60 mm and a height of 850 mm.

When cutting wood, do not forget process the edges of the slats. This will avoid splinters and increase the aesthetics of the rabbit cage design.

The base frame and shelf support are attached to the main posts. To do this, four boards are screwed into the upper part of the frame with self-tapping screws and at a distance of 372 mm from the floor. It is important to correctly mark and monitor the geometry of the structure using a carpenter's square and a level. The result should be a smooth, stable structure without distortions or crooked corners.

To make a cage with an additional compartment, a neat figured cutout is made in the front board of the upper frame. The cut out part is attached to the old place using a piano loop. A narrow hinged part will provide access to the inside of the cage in the future.

WITH inside the upper and lower frames are mounted as spacers additional slats. They eliminate the instability of the structure and serve as support for the flooring, so they require especially careful adjustment.

DIY rabbit cage step-by-step instruction. Photo

In the corners of wooden boards or boards used as a shelf and base of the cage, a cutout is made for support legs. The shields are installed in their places, after which the work at this stage is considered completed.

Main compartment assembly

A rabbit cage should please the owner not only with its durability and reliability, but also with its attractive appearance. Assembling a cage for rabbits begins from the front part, and step-by-step instructions will help you understand in detail all the nuances of the work with your own hands.

Cages for rabbits drawings

At the first stage they collect door box. To do this, a rectangular frame is assembled from slats using furniture dowels and self-tapping screws. A groove is cut out for vertical movement of the door. A sliding partition frame is made that is slightly larger than the height of the box. Dowels are installed from the outer surface, after which the door is installed in place by inserting the dowels into the prepared slots on the side jambs.

From wooden slats install compartments on both sides of the opening. The rear part of the structure, as well as the side walls, are assembled.

How to make a rabbit cage. Photo

The eight slats from which the roof rafters will be made are cut at an acute angle. The rafters are assembled by fastening the pointed elements in pairs, after which they are finally fixed with self-tapping screws. After this, the brackets are removed and the rafters are attached to the base of the roof.

Triangular elements are cut out of a sheet of plywood to block access from the doorway to the roof. They are attached with self-tapping screws to the central rafters in accordance with the attached diagram.

DIY rabbit cage step by step instructions. Photo

The roof is sheathed plywood sheets, cutting them according to the drawing. The rear slope is made with a cutout mounted on a piano hinge. The hinged roof section makes it easier to access internal space cells. To connect the central part of the front roof slope with the side elements, small sections are cut out in its corners.

After assembling the base of the rabbit cage with your own hands is completed, the structure is treated with drying oil, dried, and then painted in one or two layers oil paint. Despite the longer drying period, it will reliably protect the wood from moisture.

How to sheathe walls and roof

Cages for rabbits drawings

The inside of all the walls, as well as the door of the rabbit cage, are covered with your own hands using a screwdriver, self-tapping screws and a metal mesh with a mesh size of no more than 25x25 mm.

First, the ends of the cage are sewn up, and then the front wall is mounted above the doorway.

To make the design convenient to transport, folding handles are screwed onto the sides of the frame support frame.

Install on the front board of the upper support frame valve for fixing the narrow folding part.

The latch is also installed on the cage door.

Decorate The design can be made using the figure of a rabbit cut from plywood. It is painted and then glued or secured with self-tapping screws to the front wall of the roof.

Protect the piano hinge, which ensures the mobility of the folding part of the roof, can be done using universal adhesive tape. Glued on top of the metal, it will prevent rust and ensure reliable operation of the part.

Using a stapler and metal staples measuring 8 mm or more, attach them to the roof sheathing of the rabbit house. bitumen shingles.

DIY rabbit cage step by step instructions. Photo

Using a special glue for soft roof, from a long, narrow piece of bitumen canvas they equip roof ridge.

cut out plexiglass according to the size of one of the side walls, after which a latch is mounted in its upper part. If necessary, this element will be able to protect animals from drafts and rain. The plexiglass is installed on the frame, securing it at the bottom with furniture dowels, and at the top by fixing the latch bolt in a pre-drilled hole.

Small ladders are assembled for animals and inner house. After impregnation with drying oil, the parts are painted and placed inside the cage.

After the paint is completely dry, the cage is transferred to permanent place, prepare provisions and move the rabbits into their new home.

Despite the fact that rabbits are not particularly demanding animals, it is still better to rely on the opinion of experienced people in the manufacture and placement of the cage.

The main criterion for choosing a place to install a rabbitry is the absence drafts. In addition, in the summer, it is better for animals to be in the shade, so you will have to build a shed or place cages in a barn.

We must not forget that when breeding rabbits, you will have to resettle the young animals, keep pregnant females and males separately, etc., so you won’t be able to get by with just one cage. It is better to always have free space at hand, and the cages themselves should have walking areas.

Listen to the advice of experienced rabbit breeders, and you won’t have to fix own mistakes and miscalculations.

Floor The rabbitry is best made from mesh or slats laid at a distance of 1.5 cm from each other. When using the cage outdoors, they also install a lower, folding floor tier made of boards.

The roof the cages installed in the room are made of the same material as the walls. Outdoors, the rabbitry is covered with waterproof roofing material. It is better not to use tin for this.

On the street, houses for animals are located on supports height from 0.5 to 1 m. It is best if inside the cage there is also a house with a cutout in the form of a “hole”.

Cells are divided into several branches, providing a passage for animals from one part to another, as well as hinged lids for cleaning individual “rooms”.

The dimensions of the rabbitry in which it is planned to keep the males are sufficient for them to roam freely. We must remember that males who lead a sedentary lifestyle can become infertile.

For every 3-4 females make separate spacious cage.

Baby rabbits kept in the same room with a nursing rabbit. At the same time, they keep one cage free nearby, placing the mother with the smallest animals there for additional feeding.

The best material for a rabbitry is wood - boards, slats, plywood, laminated boards. They make the power frame and roof. Depending on the climate and installation location, cage walls are made of mesh, plywood, slats or boards. During the work, special attention is paid to the finishing of materials so that animals cannot be injured by splinters, sharp parts of the mesh or protruding edges of nails and screws.

Rabbit cage sizes

The dimensions of cages for breeding rabbits vary widely depending on the size of the animals, breed, purpose of the cage (for males, females with children, rabbits, etc.).

For nursing rabbits The dimensions of the cages must be at least 1.70 - 1.85 m in length, 1 m in width and 0.6 - 0.7 from the floor to the lid. The cages are placed at a distance of 0.7 - 0.8 m from the ground on trestles or supports. Animals weighing over 5 kg require rabbit hutches 1.3-1.5 m long and up to 0.7 m wide. In this case, the height of the rear wall should be 0.4-0.45 m, and the front wall should be 10-15 cm higher.

Young animals rabbits are placed in group rabbitries, where they contain from 8 to 20 individuals. From 3 to 5 cubs who are under 3 months old are placed in individual cages. For older animals, no more than 2 - 3 animals per cage are placed. In this case, there should be at least 0.5 square meters per individual. m of area, and the height of the rabbitry should be more than 35 cm. In group cages, there should be at least 0.2 square meters per rabbit. m, which must be taken into account when making a rabbitry and placing animals.

Cage sizes for rabbits. Photo

An adult requires a room with a minimum size of 1×0.6 m and a height of 0.6 m, but it is better to increase these dimensions by 20 - 30%.

The cages are placed in one or two tiers (the so-called shed). Depending on the size of the animals, the width of the shad is made no more than 2 m, and the depth - up to 1 m, placing the cages at a height of about half a meter.

For breeding, a double rabbitry is used with a queen cell - a removable feed compartment for keeping animals up to 1 month. The cage is divided into compartments by a wooden partition with a 17x20 cm hole.

The main thing is that animals in captivity feel comfortable, so it is recommended to follow all the advice on their placement and maintenance.

Cage designs for rabbits

A two-tier portable rabbitry makes it easier to care for and feed rabbits. It is enough from time to time to move the structure to a place with thick grass - and the animals are provided with food and a clean place to walk.

Photo of a cage for decorative rabbits

A wooden structure, on the roof of which there is a low box with a moisture-proof bottom, will allow you to grow seedlings or greens on the roof of the rabbitry. This solution is not only highly practical, but also looks impressive on the site.

Rabbit cage. Photo

"Two-room" house for animals with common area for feeding makes it easier to care for animals and allows you to increase the space intended for their walking.

Large cage for rabbits. Photo

Designs of cages for rabbits, in which animals have access to walk on the ground, are beneficial not only from the point of view of keeping the animals, but also from the economic side. If the cell volume is sufficiently large, its production does not require large material costs.

A triangular hut cage with an aviary for walking is easy to make. During the day, such a structure is placed in a place with thick grass, and at night the cage is removed to a stationary elevation.

The spacious rabbitry, designed for two places, has a presentable appearance thanks to its spacious design, flexible roof and color scheme light colors. Blacks complete the picture metal elements door hinges and valves.

Big summer house for breeding rabbits allows you to keep up to ten individuals. The high door of the structure allows you to enter inside for feeding, cleaning and examining the animals.

A cage of increased depth, divided into two rooms, allows you to keep several individuals in each half. The enlarged courtyard provides comfort while walking and feeding animals. The contrasting coloring and copper fittings of the cage add elegance and presentability to it.

Cage for decorative rabbits. Photo

Rabbit cages installed at a height are often built in the same building as an enclosure. A common roof allows you to save material during the construction of a rabbit cage and provides comfortable and spacious housing for animals.

Rectangular rabbitry with pitched roof very easy to manufacture and provides all the convenience for animals and their care. A simple cell for rabbits can be made from wooden bars and slats, boards and wooden lining, and the roof covered with slate or soft roofing.

DIY Zolotukhin cells

Cages designed by a Russian rabbit breeder Zolotukhina have gained immense popularity due to their simplicity, low cost and ease of caring for animals.

The advantages of this type of cells include:

• sloped slate or plywood floor with mesh near the back wall;
• three-tier structure of six cells. Shifting the cells to the width of the grid in the floor makes cleaning easier;
• the possibility of arranging a queen cell in a regular cage;
• feeder special design, which does not require opening the door when dispensing food;
• low cost.

Improvements adopted by an experienced rabbit breeder-innovator bring the keeping of rabbits closer to the conditions in which they find themselves in their natural habitat.

Design Features

To make a cage for Zolotukhin rabbits, you can use wooden boards and slats, slate sheets, tin, polycarbonate panels, metal mesh.

The frame of the structure and partitions are made of wood, and the floor and roof are made of flat slate. The doors and a small part of the floor at the back wall are covered with mesh. Wooden elements the structures are sheathed with tin to prevent rabbits from chewing them.

Rabbit cage size:

• cage width - 2000 mm;
• height of the three-tier structure - 1500 mm;
• depth - from 700 to 800 mm;
• doors - 400×400 mm;
• floor mesh width - 150-200 mm;
• the difference in the level of the front and rear parts of the floor is from 50 to 70 mm.

Drawings of Zolotukhin cells. Photo

Each of the three levels consists of two cages, separated by two board partitions, between which hay is stored. The floor, also known as the roof for the lower tier, is made of slate. The back part of the floor up to a width of 200 mm is made of mesh. Each upper cell is extended by the same amount relative to the lower one so that feces are removed onto the floor or ground. Rear wall made of polycarbonate and installed in an inclined way.

Exact dimensions for making cages are not needed; the diagram given by the rabbit breeder is sufficient. This structure is a structure with a queen cell, so for the usual keeping of rabbits, the wall with the opening will need to be replaced with a solid wooden panel.

The queen cell door is not made of mesh, since the nest requires shade and shelter from drafts. To prevent the young animals from falling out when cleaning or feeding, a board 10 centimeters wide is nailed to the front of the shelter.

The design with a fenced-off queen cell makes it easy to expand the space for growing rabbits. To do this, just remove the board partition.

IN winter time Zolotukhin puts him in the cage queen cell-burrow. He is wooden box with increased rear wall height. This allows you to create the necessary expansion in the depths of the rabbit hole. The hole in the queen cell is cut out so that there is no threshold between the box and the floor of the cage.

Dimensions of the winter queen cell of Zolotukhin cage for rabbits:

• top and Bottom part- from 300×300 to 400×400 mm;
• front wall - 160 mm;
• rear wall - 260 mm;
• opening height - 150 mm.

The feeder is a long tray that takes up 2/3 of the length of the cage. Its front wall is twice as large as the back wall, and the bottom slopes into the cage at an angle of up to 35?. The feeder is mounted on a rod hinge, which allows you to install the tray in the door. This eliminates the need to open the cage when feeding and makes it easier to clean the feeder from leftover food.

DIY rabbit cages. Video

As you can see, making a rabbit cage with your own hands is quite simple. At the same time, it is important to ensure the comfort and safety of pets, as well as to provide for ease of feeding and cleaning.

In this article we will tell you how to make a rabbit cage with your own hands (step-by-step instructions). Creating cells with your own hands can easily be done from scrap materials, such as waste boards, pieces of plywood or chipboard, etc.

The design of the cells can vary greatly, but it is best to choose one that will not take large quantity time and will prove suitable and practical for feeding rabbits, inspecting them and cleaning them.

Simple rabbit cage design

The most effective way to breed rabbits is Mikhailov mini-farms, which can provide intensive breeding of rabbits at minimum costs time for the farmer to care for the animals.

The design of Mikhailov’s cages is very well thought out and provides for automatic cleaning and provision of food for animals, water heating in drinking bowls, which is really important in the cold season, as well as heating of the queen cell in order to increase the survival rate of newborns in the winter.

In order to start breeding rabbits you do not need any special costs: rabbit cages You can make drinking bowls and feeders yourself, hay and branches can be prepared in the summer, root crops and vegetables can be taken from your garden.

The largest part of the costs will go to vaccinating animals and concentrating feed.

It is best to place adult rabbits and female rabbits with baby rabbits in two-section cages. These dimensions are usually used as a guide for building cells: cell length one hundred twenty centimeters, cell height fifty centimeters, cell width seventy centimeters.

Young animals

The young should be kept in a large group cage, the size of which will correspond to the number of rabbits.

For example, for eight little rabbits, a cage with the height and width as in the picture above is suitable. It is necessary to take into account the fact that in each cage you need to place rabbits of the same sex, approximately the same age and weight.

DIY rabbit cage step by step instructions:

First you need to make a frame from wooden beams, its height should be 55 centimeters, its length 240 centimeters, its back thirty-five centimeters, and its front fifty-five centimeters;

It is necessary to provide for the presence of nesting compartments inside, where a queen cell for the rabbit will subsequently be inserted or a small house will be placed;

A partition with a hole for the passage of rabbits is placed between the nesting compartment and the feeding compartment;

• The roof is made on hinges so that it can be raised if necessary;
• In the nesting compartment, the door must be made solid, made of wood, and
• in the aft compartment the doors are made of metal mesh with small cells;
• the floor must be laid with slats, with a gap of one and a half centimeters;
• in the nesting compartment the wooden floor must be solid;
• you need to install a tray under the cage;
• after making a cage for breeding rabbits, you need to equip it from the inside: feeders for grain are made, shelves and mangers are installed;

If rabbits are kept outdoors, the cages should be installed on bars so that they rise above the ground by about seventy centimeters. This should protect the rabbits from rodents and other animals.

This is the step-by-step instructions for creating a cage for rabbits with your own hands. Through simple materials and a little effort, you can create your own rabbit farm and run a fairly successful farm.

There are special rules that should be taken into account when building a rabbitry, regardless of its size.

1. The size of the cage must be just such that the rabbits can move freely and do not interfere with each other to eat, sleep and especially play. If there is not enough space in the cage, the rabbits will begin to be lazy, and this will have a very negative impact on them. Perhaps such individuals will have no offspring at all.

2. For three to four rabbits, it is necessary to allocate a separate space. At the same time, it should be quite spacious. If a person decides to start breeding rabbits, he needs to keep the little rabbits with their mothers because they feed them.

3. One of the cages should always remain free, since not all rabbits reach required size and weight. In order to fatten them up the right size they are simply housed and fattened separately, and this naturally requires a separate cage.

DIY rabbit cage video collection

https://youtu.be/addXcSFhn8g

The most widespread in household plots is double designs of the Research Institute of Fur Farming and Rabbit Breeding named after. V. A. Afanasyeva.

Such designed to support two full-aged rabbits or two groups of young animals. Cage length 220-240 cm, depth - 65 cm, front wall height - 50-60 cm, rear wall - 35 cm.

Double cage for adult rabbits with a nesting compartment (dimensions in cm.)

The roof is pitched with a backward slope and a canopy protruding forward by 20 cm and on the sides by 10 cm.

In a double room On the side walls there are two nesting compartments with a solid floor, and in the middle part there are two aft compartments with a slatted or mesh floor. The length of the nesting compartment along the facade is 40 cm, and the length of the aft compartment is 65 cm.

Aft compartments in separated by mangers made of two frames covered with coarse mesh. The nesting and feeding compartments are connected by means of a hole measuring 20x17 cm. Removable feeders, drinking bowls, as well as two mesh (feeding compartments) and two solid plank doors are hung on the front side.

In the cold season, mesh doors are covered with mats, blankets and other insulating materials.

And amateur rabbit breeder A. A. Zhashkov in these cases closes the metal mesh of the doors with a glazed frame; it is hung on two nails bent in the shape of a hook. In calm, clear weather the frames are raised, and in stormy weather they are lowered. When using glazed frames, rabbits do not feel a lack of light in any weather, duration daylight hours for them it is not artificially shortened.

They are installed on legs at a height of 70-80 cm from the surface of the ground in two, less often - in three tiers. In this case, moisture-proof layers or trays are installed between the cells of adjacent tiers.

In these rabbit cages You can keep not only full-aged rabbits, but also young animals. The length of the cage with the enclosure is 2 m, the width of the cage is 0.65 m, and the width of the enclosure is 0.60 m. The enclosure is connected to the cage by a manhole, which, if necessary, is covered with a partition.

Double cage for keeping rabbits of the Klenovo-Chagadayevo state farm system (dimensions in cm)

The floor in this rabbit cage– mesh; when it gets colder, the mesh is covered with a solid particle board. Nurseries, drinking bowls and feeders are often reinforced on the front wall, and sometimes inside the cage.

Amateur rabbit breeder E. M. Slesarev successfully uses mobile cages with mesh enclosures in the summer. When keeping rabbits in these cages There is no need to prepare green fodder, prepare it for feeding and distribution, as well as clean the paddocks.

The principle of using mobile cages for rabbits- sequential movement of them along personal plot for the purpose of clearing vegetation.

Combined cage with walking for keeping rabbits

Rabbit cages with enclosures mounted in blocks of three types: for four adult females, for two breeding males and for six litters of young animals aged from 3 to 5 months. Mobile units are mounted on small wheels.

For combined keeping, rabbit breeders use both portable rabbit cages. The cage should be light, the roof should be waterproof, pitched, with a slight slope. The first quality is necessary to facilitate the movement of portable cages indoors for the cold season and their installation in two or three tiers

Portable rabbit cage

Since ancient times, rabbit breeders on homestead farms have used a cage-cage with a triangular configuration to keep adult rabbits and young animals on the grass after transplanting; its length, width and height are 2 m each.

Cage frame- from wooden blocks. About a third of the cage is lined with boards on all sides, which reliably shelters the animals from rain and heat. A door is installed on one side of the shelter, and the rest of the cage is surrounded with a metal mesh.

Cage - cage

The cage-cage is periodically, after the rabbits have completely eaten pasture (grass), moved to a new place.

Convenient, very practical rabbit cage developed by amateur rabbit breeders I. A. Komov and S. F. Kuzmin. It was exhibited at the Exhibition of Economic Achievements of the USSR and is now referred to as the Komov-Kuzmin cell. Its dimensions are 110x80x50 cm.

Usually these cages are for rabbits with intervals between them of 15 cm, they are placed in two tiers. The roof of the lower tier cage is covered with linoleum, in the middle of which a gutter is made with a slope. Peat chips are usually poured onto linoleum, which weakens the pungent odor of excrement and absorbs moisture.

The cages are equipped with original folding feeders with a wire canopy over them. When the rabbit lowers its head into the feeder, the visor rests on it, preventing the animal from scooping out the food with its front paws.

Novice rabbit breeders, in the absence of the necessary building material, often make rabbit cages from planks of various boxes, sometimes the boxes themselves, as well as old barrels, are adapted for keeping rabbits.

Using container boxes for keeping rabbits

The latter are placed under a light canopy or simply in the open air in the “on their side” position. The barrels are laid in a row on beams raised to a height of 70-80 cm from the surface of the ground.

Sometimes they are placed in two tiers, placing one upper barrel in the “depression” between the two lower ones. It is enough to install a mesh door with a latch in the front wall of the barrel - and the rabbit cage is ready.

Using barrels to keep rabbits

2. Cages for breeding young animals:

As already noted, baby rabbits can be kept in cages for full-aged rabbits.

On small farms, young animals of 3-4 heads are kept in cages for adult livestock, or 10-15 rabbits are kept in cages for group cages for rabbits with walks. The walk consists of a wooden or metal frame, surrounded by galvanized metal mesh.

The floor is mesh with a cell measuring 16x16 mm. The frame has a length of 200, a width of 100, and a height of 60 cm. The paddock is in contact with the shelter, which has 2-4 manholes. The shelter floor is removable; if necessary, it can be replaced with wooden boards or on the grid.

The wooden roof is hinged. Group cage for rabbits installed on beams at a height of 70-80 cm from the soil level.

Group cage for keeping young rabbits (projection)

Feeling good baby rabbits in a group cage, consisting of wooden frame. The roof, as well as the back and side walls of the cage are made of wood material, and the floor and front wall are made of galvanized metal mesh.

Drinkers, feeders, mangers are attached to the front wall, and two doors are hung. The roof of the cage is single-pitched, wooden, with a canopy 30 cm wide.

Group cage for keeping young rabbits (general view)

When keeping cages outside, especially year-round, some difficulties arise. In winter, individual parts of the cells have to be covered with plastic film, roofing felt or linoleum.

IN summer period installed in the shaded part of the site or create artificial shadow over batteries of cells. The accumulation of blocks of cells, multi-tiered cells worsen the aesthetic appearance of the site, which causes certain criticism from others.

In this regard, the experience of amateur rabbit breeder A. A. Shirikalov, who keeps rabbits outdoors in cages all year round, is instructive.

Cell batteries made of metal mesh are raised to a height of 0.5 m from the ground surface. The rabbit breeder covers three sides and the roof of the cages with linoleum waste.

In summer, to reduce adverse effects high temperature(rabbits refuse food, their growth slows down, and their live weight decreases), a “protective tent” is erected over two batteries of cages.

To do this, install poles along the batteries at a distance of 2 m from each other, 1.5 and 2 m high. The poles at the top are connected by poles that form a frame above the batteries of cells. On poles and roof poles, aluminum wire is stretched on both sides at intervals of 20 cm.

In the spring, legenaria seedlings are planted on both sides of the battery next to each pole. The plant, with its rapid growth, forms a green tent over the rabbitry, creating the necessary coolness. White inflorescences of lagenaria appear in June.

In addition, the plant produces juicy fruits weighing up to 5 kg, which are used in feed mash. From one lagenaria bush in favorable years you can get up to 60-80 kg of fruit.

Some rabbit breeders use vegetable peas, climbing beans, and perennials to create a “green tent” or “green wall.” flowering plants: climbing roses, clematis, etc.

In the southern treeless zones of the country for building cages for rabbits They use ordinary brick, clay wattle, and adobe brick. Rabbit cages These materials are used to build like wooden ones, except that their lower part, 10-15 cm wide, is lined with mesh or carving on the inside.

To build a roof, first a flooring is made of poles, then a sheathing, usually made of thin brushwood, is placed on them. The top of the lathing is covered with a 25 cm layer of reeds or straw, which are secured with straps. After this, the roof is filled with liquid clay, and then coated with greasy clay. Adobe cages with a clay-straw or reed roof protect rabbits in southern zones well from overheating.

IN last years for individual household plots, the industry began to produce mesh cages for rabbits, which can be purchased through the retail chain. These cages are used under a light canopy in the summer, and in insulated rabbit sheds in the winter.

The Zvenigorod production association manufactured the KSK-1 cage, intended for keeping rabbits in rabbitries. It consists of two paddocks separated by nurseries.

The doors are located at the top. The floor is made of mesh with 16x48 mm cells, and all other parts of the cage are made of 24x48 mm cells. On the front wall, a collector pipe is secured with special clamps, which, through a fitting rubber hoses connected to automatic drinking bowls.

Mesh cages for rabbits

(a – with two paddocks, b – for young animals, c – three-tier cage)

(1 - nursery, 2 - door, 3 - collector pipe, 4 - hopper feeder, 5 - hose, 6 - stand, 7 - drinking bowl, 8 - tray, 9 - paddocks, 10 - feeder for mixers, 11 - feeder for grain and granules)

When installing cages in one row, the collector pipe can be connected by a coupling to the same tube of the next cage. The cage itself is secured with clamps to 4 metal posts.

Under the rabbit cage At a distance of 13 cm from the floor there is a solid metal tray intended for collecting rabbit excrement.

The KSK-1 cage can be installed in 2 and 3 tiers. For this purpose, its lower part is equipped with special sockets. Depending on the complete set, the cage was supplied in 4 versions: KSK-1-1 (with drinkers, feeders, collector and tray); KSK-1-2 (without drinkers and collector); KSK-1-3 (without drinkers, collector and feeders); KSK-1-4 (without pallet).

The main disadvantage of such cages for rabbits- the upper location of the door, which makes it difficult to service animals, especially with multi-tiered placement of cages.

3. Transport cages for rabbits

When purchasing breeding rabbits, selling them from breeding farms, sending them to procurement points and meat processing plants, they use special transport cages for rabbits dimensions 160x48x35 cm.

Transport cage for rabbits

The length of the cage is divided into equal sections by light partitions. Their front wall also serves as a door.

In the back of a car transport cages for rabbits usually placed in 4-5 tiers with the doors facing outward. For stability, they are fastened with ropes and, if necessary, covered with a tarpaulin. Sometimes rabbit breeders have to (for mating, exchange of producers, delivery to shows, exhibitions, etc.) use individual portable cage for rabbits.

Transport box for rabbits

The cage as a whole is light, with a dense, waterproof bottom, above which a grate is placed at a distance of 1.5-2 cm from it, which serves as the floor of the cage.

You can build cages for rabbits with your own hands from available materials: unnecessary boards, plywood, chipboard, slate, bricks, metal cutting, tin, etc. The design of the cages also varies, but it is better to choose one that will not take you a lot of time to make and will be convenient for feeding rabbits, inspecting them and regular cleaning.

Types of cages for rabbits and possible materials for DIY work

Not all types of cages can be made with your own hands, but many of them can definitely be made if you know the sizes, have drawings and basic skills. So, what types of houses for the eared tribe exist?

By size and height:

• simple one tier,
• bunk,
• three-tiered,
• multi-tiered.

For which rabbits:

• for young animals,
• females,
• decorative,
• giants and dwarfs, etc.

What materials can it be made from:

• tree,
• metal (iron, etc.),
• metal profile, etc.

Options can be both summer and winter. There are types for keeping outdoors or in an apartment. They can be monolithic or portable, especially if the rabbits are dwarf and kept at home. The houses can also be fattening houses. There are also industrial buildings, but we will not talk about them.

Some options for homemade rabbit houses in the photo

Wooden with mesh
Combined wood and mesh
From metal profiles and wood using sect
Made of wood

Drawings with dimensions of some types of cells

2 tiers
Mikhailov's cage
Simple scheme
Zolotukhin cell

General step-by-step instructions for making it at home

To start rabbit farming, you don’t need any special investments: you can easily make cheap cages for rabbits, drinkers and feeders yourself, hay and branches can be prepared in the summer, root crops and vegetables can be taken from your own garden. The main expenses will be required only for concentrated feed.

Each cage should contain rabbits of the same sex, approximately the same age, weight and temperament

It is recommended to place adult rabbits and female rabbits with offspring in one- or two-section cages. Standard sizes correct cages for rabbits: length about 100-120 cm, height 50 cm, width about 70 cm. It is better to keep young animals in a group cage, the size of which corresponds to the number of rabbits. For example, for ten little rabbits, a house with the same height and width as indicated above, but up to 170 cm in length, is suitable. It should be remembered that rabbits of the same sex, approximately the same age, weight and temperament should live in each cage.

Even novice rabbit breeders will find it easy to figure out how to build a rabbit cage consisting of two sections.

Step-by-step production of cages for rabbits:

At street maintenance For rabbits, the cages should be placed on bars so that they rise seventy centimeters above the surface of the ground. This will protect the lop-eared ones from rodents and pets, and it will be much more convenient to maintain the houses. By constructing a cage from scrap materials, you get an original house for your pets for almost free.

Other options for rabbit houses

If the proposed tips do not adequately describe the picture of the upcoming work, you should pay attention to the most popular types of cages for keeping and breeding rabbits. They are used by experienced farmers.

Family block - three-section cage

Making a three-section cage for rabbits may seem a little more complicated, the drawings of which are presented in the tab with photographs. But in such family blocks it is very convenient to breed rabbits: the breeding rabbit lives in the central compartment of the cage, and the females live on the sides. Wooden partitions Between the compartments, the cages have manholes with plywood latches, designed to make it easy to place females for mating with a male and return them back to their compartments.

It is very convenient to raise rabbits in such family blocks

The frame can be made from bars, and the side walls, back, nest compartments with doors and partitions can be made from wide lining. A metal mesh is used for the front wall. In nesting compartments, it is advisable to provide an attic - free space between the ceiling and common roof, where female rabbits can rest from their offspring. An additional convenience of the design is the thoughtful arrangement of feeders and drinkers - the food and water in them are not contaminated, and they can be filled from the outside.

Mikhailov's mini-farms - an easy way to raise little rabbits

One of the most effective ways rabbit breeding are Mikhailov's mini-farms, which provide intensive breeding of animals with minimal care from the rabbit breeder. The thoughtful design of Mikhailov's cages provides for automatic cleaning and provision of food for rabbits, heating of water in drinking bowls to the required temperature (which is especially important in winter), and heating of the queen cell to increase the survival rate of newborn rabbits.

Not every rabbit breeder can make Mikhailov cages with his own hands. But if you wish, you can collect complex design according to a scheme that you can easily find on the Internet.

Correct houses according to Zolotukhin’s method

The famous rabbit breeder Nikolai Ivanovich Zolotukhin has been successfully breeding rabbits for several decades; such impressive experience helped him develop his own concept of keeping rabbits at home.

Their design is quite simple, and their production requires materials that are found in almost everyone’s household.

Features of Zolotukhin cells:

• the floor in the cages is made solid of slate or boards;
• there are no pallets;
• a narrow strip of mesh flooring is provided only along the rear walls of the cages;
• the rear walls are made at an angle so that the waste of rabbits from the upper tier does not fall on the rabbits of the lower tier;
• there are no special queen cells - the female rabbit arranges the nest herself before giving birth;
• There are grain feeders attached to the doors, which can easily be turned outward for filling.

After watching the video in the tab to the article, you will understand how to make cages for rabbits of the same type as Nikolai Ivanovich Zolotukhin. Moreover, their design is quite simple, and their production requires materials that are found in almost everyone’s household.

How to make your own cages for dwarf rabbits

If you decide to have rabbits at home as pets, the issue with cages will be resolved differently. In pet stores you can now find a variety of cages for decorative rabbits, but you don’t have to spend money on buying them - making a cage for a small pet rabbit will take very little time.

A cage for a dwarf rabbit is made from two side walls 70x70 cm and a back wall 55 cm high and 100 cm long. The back wall must be secured so that there is a 15 cm gap under the cage. Nail meter slats to the bottom of the cage and fasten a metal one on top of them grid. You also need to nail a mesh onto the front door. Make a mesh lid with hinges and a handle. Place a tray under the cage - the cage for the dwarf rabbit is ready! Material updated 03/17/2017