How to apply adhesive film to a wall. How to properly glue self-adhesive film to the walls in the bathroom, kitchen or nursery: stages of work, sequence, recommendations

home

Installation

Self-adhesive film has become widespread and has won many fans. The ability to add zest to the restoration of an old item is the main selection criterion of this material.

Self-adhesive film is an opportunity to restore a surface that has lost its attractive appearance. When using, it is important to familiarize yourself with the rules for using this material.

Self-adhesive film is interesting because it can be glued to almost any surface, and the absence of foreign odors and acceptable water resistance are important criteria that need to be paid attention to.

Video on how to stick self-adhesive film

When using this material, it is important to prepare the surface: level, wash, clean from foreign impurities. The concrete surface must be covered oil paint, and the wooden one is varnished. This will allow a strong and reliable adhesion of the film and the surface.

The material is prepared in advance. When gluing to a part, take into account the required edge tolerance.

How to stick self-adhesive

Your partner is yours chief assistant, when using this material for the first time. Gradual separation of the paper surface and careful smoothing will allow the film to be firmly glued to the material, and the absence of bubbles will give positive emotions at the end of the labor process.

Sometimes it happens that during operation, minor small bubbles may appear. This problem can be solved using a regular needle, which needs to be used to pierce the bubbles and then smooth them out. Do the same with large bubbles, only instead of a needle, use a regular stationery knife. With its help, an incision is made on the bladder; the knife must be sharp. After this procedure, the surface must be thoroughly smoothed.

Gluing the film to the edge will not be difficult if you make the necessary tolerances on each side of the film, cut it at an angle of 45 degrees and then fold it over the edge. When gluing an uneven edge, you need to heat it with a regular household hairdryer and only then wrap it.

Thus, self-adhesive film is an attractive material that allows old things to acquire the new kind, brings a lot of positive emotions when working.

Tag:

how to glue self-adhesive film without bubbles, how to glue self-adhesive film without bubbles, how to glue self-adhesive film without bubbles, how to glue self-adhesive film without bubbles

How often do you want to bring something new to the interior of your home, refresh the look of the room? It is human nature to constantly change the space around us. But it is not always possible to afford drastic changes.

It is in such cases that simple and inexpensive ways, for example, pasting with self-adhesive film. This material, which appeared on the market quite a long time ago, Lately is becoming more and more popular. Due to its low cost, wide range of colors and abundance of patterns, and most importantly – ease of use, film is often used in interior decoration.

Like any material, self-adhesive film has its own characteristics and requires a certain approach. In this article we will look in detail at the technology of gluing film onto various surfaces.

Self-adhesive film: material features

Now there are many types of self-adhesive film for any surface: cars, walls in any room, even in the kitchen and bathroom. What they have in common is that they are manufactured using adhesive tape technology, which combines the qualities of adhesive tape and wallpaper.

Using self-adhesive film, you can not only apply various design solutions. This material has a number of the following advantages:

moisture resistance;
resistance to high temperatures - up to 80 degrees;
a variety of not only patterns, but also textures;
low cost;
ease of use;
easy care of the pasted surface.

Ditto distinctive features self-adhesive film can also be attributed to the fact that it can be applied to any surface: wood, glass, metal, plastic, cork, ceramic tiles, plywood, drywall.

The only difficulty that you may encounter when working with this material is the need to level the surface covered with film. All defects and irregularities should be carefully eliminated, otherwise over time the film may bubble and peel off in places.

But gluing the film itself is a simple task and does not require any skills. All you need is patience, a little time and a reliable assistant in case you are covering a large surface, as well as the following tools:

pencil;
ruler;
scissors;
mounting knife;
felt spatula or special ratel;
industrial dryer.

Please note: warm up thoroughly using construction hair dryer not only the corners and joints of the surface being glued, but also the entire glued film around the perimeter.

In what rooms can it be used?

As mentioned above, self-adhesive film is not afraid of moisture and high temperatures, and she is completely unpretentious in care. Therefore, it can be used to decorate absolutely any premises and in them, and even household appliances.

In the kitchen, especially if you live in a private house, self-adhesive film will not only help you update the interior as often as you see fit without special costs, but will also serve to maintain cleanliness and neatness. As you know, it is kitchen surfaces that often become dirty and deteriorate during use. The easiest way to fix this is with self-adhesive film.
For the bathroom and toilet, pasting with self-adhesive film is also the best option. This material will protect the walls from excess moisture and splashes of soapy water, which can be very easily wiped off the surface.
Do you have little things to do? Then you know how much trouble their love of drawing on any surface causes. It is much easier to erase traces of paint or felt-tip pens from self-adhesive film than from wallpaper or fabric upholstery. As a last resort, you can re-glue the film, which will cost you very little.
In fact, self-adhesive film is an excellent material for, and no matter how old the child is, he goes to kindergarten or finishes school. A child will have fun in a room with bright colors, and a teenager will be able to independently work on the interior of the room.
If you decide to use film for covering interior items, for example, chairs, tables, cabinets, chests of drawers, then the modern range of colors and patterns of this material will help you not only update the appearance of the rooms, but also completely change the style. In the photo you can see many options that can be used in your work.

Advice: when choosing a film, pay attention to what surface you will use it for. For example, for antique furniture, transparent self-adhesive is suitable, which will help get rid of scuff marks and minor scratches without changing the color and structure of the wood. Mosaic patterns are perfect for glass.

Caring for self-adhesive film is very simple. Usually, warm water and detergent are enough for this. It is undesirable to use powdered cleaning substances, as well as solvents - they will damage both the structure of the film and its color. If the stains are quite persistent, use ethyl alcohol.

Initial stage of work: prepare the surface, cut the film correctly

Before gluing self-adhesive film, carefully prepare the surface. It needs to be cleaned well, degreased with alcohol or gasoline, and dried. The most comfortable base for applying film - a smooth surface with a varnish coating. If the surface is matte and rough, it is better to coat it with polyester or primer varnish. It can be replaced with methyl wallpaper glue.
The surface made of fabric, chipboard, plaster must be wiped down and cleaned of dust and particles of material. If necessary, use putty and acrylic primer. This will ensure good fixation of the film for a long time.
If you plan to paste over a glass or metal surface, then the base needs to be slightly moistened.
The centimeter grid printed on the reverse side will help you correctly cut the film into pieces of the required size. Apply markings on it, and leaving a margin of a couple of centimeters, cut it using scissors or a special knife.
You also need to cut the film correctly; this process has its own tricks depending on the pattern. For example, if the pattern on the film is stylized, it is better to cut along the “seams”. In case of applying a pattern with rapport, you need to cut along the front side.

The instructions for the self-adhesive film describe the gluing process in sufficient detail. You can see in practice that it is very simple and does not require much time. But be careful and be attentive when working to avoid making many mistakes that will have to be corrected.

Take the prepared “pattern” and separate the film from the paper backing by literally 5 cm. Apply the sticky side to the surface to be pasted so that the shape and dimensions exactly match.
Carefully, slowly, separate the backing from the film, while simultaneously distributing the film over the surface and smoothing it dry soft cloth. The principle of smoothing is the same as with: from the center to the edges of the canvas. This way you can avoid the formation of air bubbles.
If you notice any error during your work, you need to correct it immediately. Peel off the film and level it over the surface until it has set thoroughly. Otherwise, the work will have to be completely redone.

If you are covering a large area, make sure that the surface being treated absorbs moisture well. Clean and dry the wall on which the self-adhesive film is being applied, cover it with a layer of wallpaper glue and, without waiting for it to dry, spread the film, adjusting it to size. After this, iron the film with a dry soft cloth.

Please note: if you purchased a film that sets almost instantly to the surface, this may cause inconvenience when it comes to adjusting the dimensions. Talc and powder can help with this; they will slow down sticking. Any air bubbles that have arisen must be punctured and carefully smoothed out.

If you decide to cover metal surfaces, or synthetic materials, moisten them with water with a small amount of detergent added or a soap solution. Separate the paper backing and film completely, attach to wet surface, the solution contributes to the correct fit of the film according to the right sizes. After this, wipe thoroughly with a sponge or soft cloth.

How to remove self-adhesive film?

Over time, you may get bored with the color or design, you will want to update the interior again, and you will be faced with the question: how to remove the self-adhesive film without damaging the surface on which it is applied?

Self-adhesive film - very durable material, and it has earned its popularity precisely because of its durability. It is not recommended to do this - the coloring agents will lie unevenly on the surface. Pasting a new layer on top of the old one is also not the best convenient option. Therefore, the self-adhesive film will need to be removed.

Try using hot water first. Wet the surface thoroughly, and after a few minutes, begin to peel off the film, helping with a flat, sharp object, such as a knife or spatula. Make sure that the surface on which the film is applied is not damaged.
If option with hot water didn't justify itself, a hairdryer will help you. The fact is that the film needs to warm up properly for the glue to detach from the surface. You can also use a regular household hair dryer, but it is better to take an industrial hair dryer: it is more powerful and will heat a larger area.
In addition to a hairdryer, you can also use a heater-fan, setting it to maximum power and pointing it at the surface from which you want to remove the film. After the material softens and begins to peel off, pry up the corner and begin to gently pull the layer toward you until it separates completely.
Residues of adhesive on the surface can be removed using solvent, alcohol or gasoline, depending on the material from which the surface is made.

Video about working with self-adhesive film

As you can see, self-adhesive film is an almost universal material that will allow you to completely change your home as your imagination dictates, at any time and at no particular cost. It is not at all necessary to change the environment for the sake of new experiences; it is enough to use this easy-to-use material to make your life sparkle with new colors.

If you have already dealt with self-adhesive film in the interior, please tell us about it in the comments and share your experience with other readers.

Using adhesive film for furniture is inexpensive and easy way give a second life old furniture, doors, glass, walls and other surfaces.

The film may be useful for rented apartment when you don’t want to spend money on buying new furniture, and also if you want to show your imagination and turn a boring cabinet or chair into a small masterpiece.

Many are experimenting with country furniture, which after decoration acquires fresh look and can last for more than one year.

Material with a tint will add a highlight to the surface. natural wood or marbled, with geometric patterns or abstraction. Moreover, the choice of colors in stores is very large.

The advantages of self-adhesive film include:

price,
availability,
ease of use,
moisture resistance,
durability,
health safety,
Possibility to wash with water.

But in order for the film to cope with its tasks, it is important to stick it correctly.

What is used to paste furniture over – types of films for pasting furniture

The choice of material should be approached responsibly, because in markets and in stores you can find cheap polyethylene and polypropylene options, which are inconvenient to use and do not provide the desired result.

The best option is polyvinyl chloride, or PVC, which is traditionally used in everyday life and is recognized as safe and reliable.

It is necessary to make sure that the material has a protective layer, this is especially important if you are working with kitchen furniture. High loads, exposure to food, impacts from sharp foods can quickly damage the material, and the film will not last longer than a month.

Cheap material loses color very quickly. To prevent this from happening, buy options with a layer of ultraviolet stabilization, which will protect the furniture from exposure to sunlight.

For the kitchen and bathroom, choose moisture-resistant models, and if the furniture will be used near heating devices, pasting is done using a thermally stable polymer.

Self-adhesive film can also be used as a means of protection, for example, from moisture accumulation.

Those who appreciate natural shades should choose self-adhesive wallpaper for furniture painted to resemble wood, stone, fabric or ceramics. But it will look stylish only if the material is really High Quality, and not a cheap Chinese knockoff, not even remotely similar to the original.

To decorate furniture in the hallway, as well as in rooms with low lighting, designers recommend using glossy film, and matte for the bedroom or kitchen.

Those who are confident in their taste may prefer not boring monochromatic options, but materials with luxurious patterns with a polymer coating.

VIDEO INSTRUCTION

We gradually glue the film onto the furniture - application technology

Since the film is not afraid of high temperatures and moisture, is easy to care for and practical, it can be used in the following rooms:

Kitchen. You can paste over both furniture and other surfaces that are often susceptible to contamination. It is especially convenient to use self-adhesive material in the kitchen of a private home.
Bathroom. Here, using this material you can protect walls from moisture and soap suds.
Children's room. It is easy to wash off paint, markers and other contaminants from the film.

Let's look at the procedure for covering various surfaces with film:

Surface preparation- first and most important stage. The base for the film must be cleaned of all contaminants, and ideally also varnished. You can also prime an uneven surface with wallpaper glue or varnish.
Material cutting. There should be plenty of pieces of film. It will also be more convenient to cut if reverse side scale is applied.
Separation from protective film . On the back side, the manufacturer usually indicates recommendations for using the material; study them and adhere to them. Attach the material to the base and, holding it with one hand, remove the protective layer, and smooth out air bubbles with the other. While the film has not set, there is a little time to correct the material and lay it out more evenly. In a few hours it will completely set, and it will no longer be possible to correct the result. To facilitate the gluing process, many people wet the surface to make it easier to trim.

To ensure service life self-adhesive film for kitchen or the living room was long, it is recommended to follow these tips:

remove light stains from the surface using warm solution with a mild detergent,
Ethyl alcohol will help remove more serious stains,
Do not use acetone, gasoline and other aggressive liquids, as well as abrasive substances that leave scratches.

VIDEO ON THE TOPIC

to slow down the gluing speed, sprinkle it with powder, it will make it easier to join the drawings,
if there are any bubbles left after gluing, pierce them with a thin needle,
When gluing metal or glass, wet the surface with water and detergent,

And if you get bored with the film and need to remove it, use the following algorithm:

Wet the surface with hot water and after a few minutes try to separate it with a sharp object - a spatula or knife. Try not to damage the base, because a new film will be glued onto it.
If hot water did not help, heat the surface with a hairdryer. You can use a regular hair dryer, but a more powerful one is an industrial one.
In addition to a hairdryer, you can use a heater-fan at maximum power. The material will soften and it will be easier to peel off the surface.
If there is glue left on the surface, gasoline, thinner or alcohol will help get rid of it.

Thus, universal and practical material self-adhesive film will help change the design of the apartment from minimal costs and experiment with implementing design ideas.

In order to hide scratches and defects received during the use of furniture or to renew the surfaces of facades and panels, a special film is used. It is durable, has an attractive appearance and rich color palette. To figure out how to glue self-adhesive film to furniture, you need to consider in detail its features and application methods.

Furniture film helps to visually refresh furniture panels that have become boring over time. short term. With the help of simple manipulations, the procedure can be done with your own hands in a few hours. To do this, you only need the material itself and sharp scissors or a construction knife.

Today, the range of this raw material occupies a leading position among other methods of furniture restoration. Using the material, you can bring any design solutions to life without spending a lot of money.

The popularity of using self-adhesive is due to its following advantages:

the material is supplied in rolls, making it easy to cut rectangles and squares of the required dimensions;
the film helps protect furniture from future scratches and chips, and if they do appear, replacing the material will not be difficult;
self-adhesive film will help preserve family budget: you don’t have to purchase a new headset if it is possible to update old products;
no additional tools are required for work;
good for kitchen furniture, protecting it from grease, dirt and other damage;
the material is easy to clean, self-adhesive compounds can be treated with detergents and gels.

The raw material consists of several layers: front, adhesive, protective. Each of them performs its own function. The very first layer - the front layer - is made of different options materials:

polymer film - is a self-adhesive type of vinyl that perfectly covers surfaces. She looks very beautiful on furniture, and her decorative abilities are invaluable. In addition to vinyl, PVC or polyester is used;
foil - used for lining less used pieces of furniture, most suitable for wall cabinets;
paper - paper-based material can be glued to the ends of the shelves, since such a film does not withstand constant mechanical influences.

Decorative film can imitate a large number of surfaces: leather, wood, natural stone, ceramics, tiles and fabric. Thanks to this, it has a wide range of applications not only in updating facades, but also in ordinary decor.

Depending on the material of manufacture, self-adhesive film is divided into:

single-layer roll products - produced on the basis of polymers, additives in the form of plasticizers, which give the raw material strength: all components are mixed together and flat rolls are formed by extrusion;
two-layer models - in in this case In manufacturing, two fabrics are used: the base and the surface, this material is technical specifications worse than its single-layer counterpart.

Anyone can glue furniture on their own; no special skills are required. Before you start working, choose the surface structure of the film; it can be glossy, matte, transparent, mirror and holographic. Each type is used in individual cases, so it is important to determine in advance the purpose of the raw material.

Choosing a film based on the type of room

In order for pasting of furniture with self-adhesive film to be successful and to serve for many years in the future, you need not only to purchase quality material, but take into account the type of room in which the surface will be used. Raw materials for the kitchen and bedroom have their own characteristics, so when choosing, use the following tips:

film for furniture intended for the bedroom or living room should not only have an attractive appearance, but also fit into the interior. If previously the fronts of cabinets and tables had specific color, it is not at all necessary to repeat it - you can purchase rolled products of a different shade, but do not forget about compatibility with upholstered furniture and finishing. Ideal for well-lit rooms matte film– its structure will be clearly visible when sunlight. When choosing a self-adhesive base for the bedroom, pay attention to products that imitate natural materials. Such options would be appropriate for decorating the facades of cabinets and chests of drawers;
to kitchen set looked like new, it can also be pasted over vinyl material. For this room, the strength characteristics of the raw materials and the ability to constantly withstand mechanical stress are very important. Gloss would look good here, but remember that the surface requires careful care. Many designers recommend using self-adhesive compounds with photo prints and bright images. The pattern of citrus fruits will suit the kitchen space;
You can also update the furniture in the bathroom or toilet using this raw material. Thanks to its properties of not absorbing moisture, the pasted surface will not only look beautiful, but also be practical. For the fronts of cabinets and cabinets in the bathroom, use options that are consistent with color scheme facing tiles floors and walls;
To freshen up the children's room, glue on material depicting your favorite cartoon characters. Children always enjoy new things, and such a surprise will delight them. Assortment of films with fairy-tale characters, will help the baby do right choice. Raw materials are used to process wardrobes, bedside tables and even tables to perform homework. If the plans do not include a complete replacement appearance furniture, you can focus on using individual patterns for decoration.

To update the outside of glass cabinets and display cases, treat the furniture with a transparent self-adhesive film.

This material often has a small printed pattern that will help diversify glass facades.

When choosing a material, think carefully about the future design. Some varieties of holographic or glossy films can have the opposite effect and create a cluttered feeling in the room.

Application technology

Before sticking the self-adhesive film on the furniture, you need to prepare the tools for the job. These include:
scissors and a sharp utility or construction knife
soft fabric to smooth out wrinkles;
roller for removing air from the material;
solvent;
primer mixture;

medium-dispersion sanding paper.

In the process of pasting furniture with film, it is first necessary to prepare the surface of the products by treating them with a special composition. For this, a primer is used, which improves the adhesion of the two planes.

Preparation proceeds as follows:
tighten all hinges and fasteners of the furniture product. Also check that all screws are screwed in completely; if this is not done, small protrusions will be visible on the glued surface, which will significantly affect the aesthetics of the appearance; examine the furniture for cracks and chips. If there are any, they must be removed using putty. Gently apply the mixture to the defect areas and fill the voids. After drying, treat the areas sandpaper
- this will give greater adhesion to the surface being glued; The next step will be degreasing the plane. Before gluing the film to furniture, soak the cloth in solvent and go through all the corners and hard-to-reach areas furniture board

, which will be subject to processing by the material.

When the surface preparation is completed, we proceed directly to the gluing process itself. To avoid shortcomings, follow the proposed algorithm of actions, which can also be found in the video in the article:
take the necessary measurements of the furniture to cut the required pieces of material;
before gluing the furniture panel, remove the material by 10 cm from the protective layer so that the adhesive base is exposed;
attach a piece of raw material to the furniture with an adhesive layer and gradually, smoothing the film with a roller, remove the remaining material from the protection;
It is necessary to smooth the plane from the edge that is already glued to the area that you are going to glue. In this way, it will be possible to avoid the formation of folds and wrinkles on the surface being pasted.

There is another method of treating furniture with film, which is based on the use of a wet solution of water and soap. Here, gluing the raw materials correctly will not be difficult. In this case, the protective layer is completely removed and the material is placed on the floor, face down. The solution is applied to the adhesive layer using a sprayer, after which the film is applied to the surface. It is appropriate to stick the material using this method when there are large areas of finishing, when it is difficult to achieve a perfectly smooth surface.

Taking measurements

Cutting the film

We apply it to furniture

Smoothing

Common mistakes

Sometimes, even after finishing the furniture, bubbles, folds and other defects may appear that were made during work. Correcting defects is not possible in most cases, so the film must be removed and the procedure will have to be repeated again. When doing the work yourself, you can make the following mistakes:

Before gluing the material to the surface, it was not treated with a cloth or brush. Important point removing dirt and dust causes a smooth coating, and the presence of small particles of dirt underneath will spoil the appearance;
the cut piece was not enough to cover the shield. This happens if you don’t take a few centimeters in reserve when cutting. Usually it is calculated at 2-3 cm, which can easily be measured on the back side of the material, where the measuring grid is located;
the drawing on the plane does not match. Answering the question: how to properly glue a film that imitates natural materials, it is worth emphasizing that it must be cut at the seams - then there will be no problems with the pattern shifting;
Furniture defects are visible under the coating. The reason for this error is poor preparation of the base or the use of too thin material. If the furniture is old enough, then it is better to use rolls with thickened front layer. Before gluing self-adhesive film on furniture, all damage must be removed.

To do the job efficiently and to paste the furniture yourself without any defects, follow the technology for applying the material. It is better to pre-twist all the fittings, and process the elements of collapsible structures separately.

Properly done work will delight all family members with a beautiful updated look of furniture products. Self-adhesive film – universal and inexpensive material , the range of applications of which is limited only by imagination and consists mainly in the decoration of various types of surfaces. Externally it is a dense roll, similar to standard wallpaper , but differs significantly in characteristics. Let's talk about what the film is intended for adhesive based

and how to actually glue it?

Advantages of adhesive-based film

The advantages of self-adhesive film: No film required during installation special equipment
, and when sticking to furniture - preliminary leveling of the surface, special skills, so that, in fact, even a child can handle the job.
There is no need to apply glue to the surface since it is already on the film.
The material can be glued to absolutely any surface (glass, wood, iron, etc.). A variety of textures, colors, shades allow you to create unique interior and decorative solutions . Matte and glossy, transparent and not, with a pattern and plain, they will become indispensable assistants
both during repairs and at home.
In addition, caring for a surface covered with such material is a pleasure! To remove dirt, simply wipe the film with a cloth soaked in warm soapy water. But the most important advantage of adhesive-based film is that you can transform a room beyond recognition for modest money. However, you should not buy the cheapest one on the market. building materials , and also trust unverified companies. Behind low price

It is extremely rare to offer a truly high-quality product.

Application of self-adhesive film

Let's consider the main areas of application of adhesive-based film: The traditional function of film is to renew old furniture that has lost its former beauty and is a pity to throw away, be it a scratched cabinet, a worn-out shoe cabinet, or old table
. By covering it with film, it will look like new. Self-adhesive imitating a natural stone or ceramic tiles, ideal for renovation kitchen - apron, bar counter, countertops, as well as renovation of finishing in the bathroom.
An adhesive-based film will return the former shine not only to furniture, but also to household appliances.
Self-adhesive film allows you to recreate when sticking to a glass surface, be it a window or glass partition, the effect of stained glass, frost, the appearance of etched or ground glass. This is especially true for residents of houses where the entire contents of the apartment can be seen through the windows, and there is a need to protect their space from the gaze of passers-by.
You can transform shabby doors using this coating.
The resulting stain on the wall as a result of the actions of young artists will also successfully hide a small element made of film.

Preparatory work

Preparation for gluing the film is carried out in the following sequence:

To work you will need scissors (knife), pencil, small cloth, ruler, hair dryer, wallpaper glue.
First you need to prepare the surface for sticking the film by removing dust, dirt and greasy spots. Then the base is wiped with a clean cloth.
To degrease the base, use any detergent or an alkaline solution. Then you should apply alcohol or gasoline and wait until the surface dries.
If you are dealing with wooden surface made of plywood or boards, chipboard, or plaster, it must be primed. To do this, use polyester varnish or methyl wallpaper adhesive.
If there are cracks and irregularities, the surface must be sanded with sandpaper and puttied, subsequently covered with acrylic primer to ensure high-quality adhesion of the film to the base.
If you need to stick self-adhesive onto plastic, glass, or metal, it is recommended to slightly moisten the base. Pre-moisten the surface with water and some detergent.
When cutting the film into pieces, be guided by the centimeter grid applied to the back of the material. It needs to be marked, taking into account the dimensions work surface and leaving a couple of centimeters in reserve.
When cutting the film, you should take into account its pattern. For example, cut stylized tiles along the “seams.” If the pattern is repeat, then it is necessary to cut the coating exclusively along the front side. If you want to cut out a specific design from self-adhesive paper, first copy it to the wrong side and carefully cut it out.

Features of film sticker

Now let's talk about how to stick self-adhesive film:

Take patterns made from self-adhesive tape and remove the film from them.
Place the pieces of material on the work surface with the sticky side so that the dimensions of the surfaces of the film and the base exactly match.
Carefully spreading the film over the surface, smooth and level it using a soft cloth, as you would when wallpapering, to prevent bubbles from forming inside.
When working with a large surface area, it must be covered wallpaper glue, and the film is glued to a damp base. Then it must be thoroughly wiped dry with a soft cloth.
If the film almost instantly adheres tightly to the base, you can use powder or talc as an assistant to slow down the adhesion.
If bubbles form during the process of gluing the film, they should be carefully punctured and smoothed out later.

Film removal procedure

Self-adhesive film with correct operation will serve long years. But if it has lost its original appearance, then it should be removed, since when you plan to paint it, the composition will not lie on it in an even layer, and it will not work to stick a new film on top.

Let's talk about how to remove the self-adhesive tape:

Wet thoroughly warm water film, leave to soak for a few minutes.
Using a sharp object (knife, spatula), carefully lift the edge and slowly pull it towards you. Where the film is strongly stuck to the surface, a sharp object will help. Be extremely careful while working so as not to scratch the side you are cleaning.
If warm water didn't help, then use a regular hairdryer. Of course, if you have a construction one, then the work will be completed twice as fast, but a home one will also work. You can even use a fan with a warm air flow for this purpose.
Point the heating object at the surface of the film. When exposed to heat, the glue will begin to come off.
Start peeling off the well-heated film from the edge. Additionally, warm up areas that are difficult to remove.
Remove any glue that remains on the surface using special liquids (alcohol, gasoline, solvent). Keep in mind that they may begin to interact with the material, so choose one that will not harm the item being cleaned.

Thus, the use of self-adhesive film - perfect solution, when there is a desire to add variety to the familiar interior of the room, give new life old items, show creativity in creating decorative elements or have fun with your child.

Sections