Rocket stove for cooking. Jet propulsion guards cozy warmth: do-it-yourself rocket stove

Despite such a loud name, a rocket stove, of course, has nothing in common with rocket and space technology. And it doesn’t run on jet fuel at all. The stove received this name for the stream of flame escaping from the top pipe of the camping structures and the sound reminiscent of the roar of an engine.

Let us immediately clarify that the stove will produce a strong sound only if the operating rules are violated - the roar of the engine occurs when excess air enters the firebox. Normally, the rocket stove will make a quiet rustling noise. It runs on wood and other fuels and is highly efficient.

The rocket stove came to us from the USA and is still little known even to professional stove makers, although it definitely deserves attention.

Operating principle of a rocket stove:

• Direct combustion. Fuel gases flow freely through the furnace channels without being stimulated by the draft created by the chimney.
• Flue gases, which are always released when burning wood, are burned. This is called pyrolysis.

The simplest jet furnace will consist of two pipes, one of which goes horizontally and the other goes up. You can use one curved pipe if you have such an opportunity, otherwise welding work is required.

The fuel in the rocket stove is placed directly into the pipe. In this case, the hot gases will tend to escape upward along the vertical section. At the end of the pipe you can place a container that will be used for cooking or boiling water. There must be a gap between the container and the pipe so that combustion products can freely come out.

What else you need to know about the jet stove:

• It is both cooking and heating.
• It is quite possible to equip the “Rocket” with a stove bench, approximately like in a Russian stove, but such a design will be much less cumbersome.
• The operating time on one fuel fill in a rocket stove is approximately six hours, and it retains heat for up to 12 hours if the metal structure is finished with adobe plaster.
• Initially, the rocket stove was intended for use outdoors, in field conditions. Portable metal structures still occupy first place in popularity, but stationary stoves have also appeared that work on the same principle, made of brick or clay.

Pros of the rocket stove:

• The design itself is simple, you can do it yourself, the materials are available.
• Ability to use different types of fuel. In such a stove, even low-quality fuel, damp thin branches, and so on will burn.
• Energy independence.
• High operating efficiency, lower fuel consumption.

Cons of a jet stove:

• It will have to be controlled manually. It is necessary to constantly monitor and regulate the combustion process.
• Some elements of the rocket stove can become very hot, especially the simplest ones. metal structures. That is, there is a great danger of burns when touched; you should be especially careful and keep children away from the rocket stove.
• It will not work to use a stove of this design in a bathhouse, since it is simply not able to quickly heat the room to the required temperature.

Now you can find the simplest diagrams of how to build a rocket stove out of 20 bricks with your own hands without mortar in literally three minutes anywhere. The first row will be solid, with a horizontal protrusion, the second will have a hole above the protrusion for loading fuel, the remaining three rows will be a pipe. It will be warm; you can simply place a cauldron or pan on top.

However, in more complex and effective options flue gases are passed under the stove bench, for example, through special channels. The second option is to install a water circuit on a simple rocket stove.

These are examples of biodesign of stoves that work on the “rocket” principle, but are much more complex and modernized, with stove beds. The construction of such clay ovens is carried out by the German company Lehm und Feuer.

Let us state that a rocket stove has many advantages, including ease of installation, the ability to be used in the field or in the summer in the yard for cooking various dishes over a live fire. You just need to understand the operating principles and design features.

The most simple solutions for organizing the heating of a private home will always be popular, especially among home craftsmen. These include a wood-burning rocket stove, which you can make yourself without significant financial costs. The heater is quite interesting and deserves special attention. Let's look at the operating principle of a rocket stove, its advantages and disadvantages, and methods of making it at home.

How does a rocket stove work?

It is noteworthy, but the so-called rocket or jet stove actually has nothing to do with jet propulsion, much less with space flights. This popular name arose for 2 reasons: due to some similarity of the operating unit to an inverted rocket and due to the buzzing sound. True, it appears in a certain mode and indicates too much air supplied to the firebox.

Important. A mode in which the rocket stove makes a loud noise or even roars is ineffective and uneconomical. During normal operation of the potbelly stove, only a quiet rustling sound is heard.

At the moment there are 2 types of jet wood stoves:

• portable;
• stationary (heating).

The Robinson camping metal stove with a folding tripod easily fits into a backpack

The simplest portable modification of the stove missile type It is mass-produced under the name “Robinson” and is intended for heating water and cooking food in camp conditions. Using her example, it is easiest to understand the principle of operation of the unit. Essentially, it is a pipe in the shape of an inverted letter “L”, as shown in the diagram:

How does a rocket stove work:

1. Firewood is inserted into the horizontal part of the pipe, which serves as a receiving hopper for fuel, and set on fire from the vertical section.
2. Natural draft occurs inside the L-shaped channel due to the temperature difference between the incoming air flow and the outgoing ones. flue gases.
3. The combustion intensity of a rocket stove increases as the body warms up, so it is necessary to limit the air supply. Otherwise, the wood will burn out very quickly - all the heat will fly out into the chimney.

The operating principle of the so-called jet furnace is to use the energy of the upward flow of combustion products. The higher the temperature of the firebox walls, the more intense the wood burns and the more powerful the flame.

Due to the natural draft that arises, a simple steel Robinson stove heats a large container of water in about ten minutes. And if you make the vertical section insulated, as shown in the diagram, then after warming up you will be able to burn fairly thick logs.

Stationary oven option

Do-it-yourself stationary rocket stoves for heating a home are equipped with a special hood to retain the heat of the flue gases and then transfer it into the room. In this case, the overall picture of wood burning is somewhat different. With a limited supply of primary air and fuel combustion, pyrolysis gases begin to be released. They are burned in the lower part of the vertical pipe, where secondary air is supplied through a separate channel.

A stationary rocket stove does not differ in operating principle from a portable one, only the flue gases are discharged through the hood and stove bench into the chimney

Note. In this regard, a wood stove is a long-burning rocket, only it does not use a fan to force air.

The hot combustion products, rising under the hood, begin to cool, after which they fall in the space between the walls and enter the chimney channel. In this case, three forces act on the gases:

1. Gravity. It causes colder and heavier gases to descend and be directed towards the exit of the chimney duct.
2. The pressure of new combustion products arriving at a higher temperature from the firebox.
3. Natural draft force of the chimney.

The sum of these three forces makes it possible to attach smoke channels of arbitrary shape to a rocket-type stove, just to take away more heat. In practice, this is used to make a heated bed from a rocket stove, as shown in the diagram:

Note. There is another way to prevent the release of heat along with flue gases to the outside. To do this, a chimney is made from the rocket stove with a water jacket and two pipes that are connected to.

A stationary “rocket” can be made of metal, add a hob and a heat exchanger to heat water for heating

About the advantages and disadvantages

So-called jet stove- This is the cheapest option for heating a private home. In this regard, she has no equal. Moreover, good master is able to make a brick stove in such a way that it will look quite decent in the interior of the room. In fact, you only have to refine the protruding metal cap and the lid of the fuel chamber. The remaining parts of the unit, along with the gas ducts, will be hidden from view.

Homemade rocket stoves certainly cannot be called super-efficient, but in general, this indicator largely depends on the homeowner himself. If you constantly burn raw wood, then it will be of little use. Just as there is no point in trying to achieve a “roaring” mode from the heat generator, mistakenly believing that it is the best. Here it is necessary to limit the air supply manually, as is done in long-burning heaters.

There is only one way to supply a jet stove with a water circuit - install a heat exchanger on the chimney and connect it to a heat accumulator or directly to the heating radiators

Many stoves, including rocket stoves, suffer from the loss of useful heat through the chimney, so in this case it would not hurt to attach a water circuit to the flue pipe, as mentioned above. Well, a large amount of heat will be taken away by the bed, although you will have to work hard to set it up. The remaining negative aspects of the rocket look like this:

1. The unit requires constant supervision and manual control, since it lacks any automation.
2. Loading firewood must be done quite often.
3. The metal cap heats up to a temperature that causes burns to a person after touching. This is dangerous for small children.

Note. Homemade rocket-type stoves are not suitable for heating a bathhouse, since under normal operating conditions they are unable to generate a large amount of heat in a short period of time.

The easiest way is to make a small portable stove with your own hands - the Robinson rocket, whose drawing is presented below. You will need cutting profile pipes, metal for legs and stands, as well as welding skills. Moreover, compliance exact dimensions indicated on the drawing are not necessary. You can take pipes of a different section, but you just need to reduce or increase them proportionally so that the parts fit together.

Drawing of an improved “Robinson” camping stove with nozzles made of a profile pipe, cut lengthwise into 2 parts

Note. Please note that the drawing shows a design improved by our expert. As befits a rocket, improvised nozzles are attached to it, which receives secondary air for afterburning, which enters the pipe through a series of holes. Due to this modernization, the combustion intensity increases noticeably. For more information about the operation of a compact wood stove, watch the video:

The most common versions of large rocket stoves are made from a gas cylinder or a two-hundred-liter metal barrel. We must understand that these ready-made elements are used as an outer hood, and the internal parts of the stove must be made from pipes smaller diameter or lay it out of fireclay bricks. Moreover, from a cylinder you can make both a stationary heater with a small bench, and a unit that can be moved.

Please note that calculating the thermal power of a rocket-type furnace is quite difficult; there is no single calculation method. It’s easier to rely on ready-made drawings of already working samples and assemble according to them. You just need to compare the dimensions of the future stove with the dimensions of the heated room. For example, for heating small room The size of the cylinder is enough, in other cases it is better to take a large barrel. The selection of internal parts for them is shown in the diagram:

2 options for potbelly stoves - from a gas cylinder and a standard iron barrel

Stove rocket from a cylinder

In addition to the gas cylinder itself, to assemble the stove you will need:

• profile pipe 150 x 150 mm for the firebox and loading hopper;
• steel pipes with a diameter of 70 and 150 mm will go to the internal vertical channel;
• the same with a diameter of 100 mm for the chimney;
• insulation (basalt fiber with a density of at least 100 kg/m³);
• sheet metal 3 mm thick.

For a master skilled in welding, this work will not be particularly difficult. The top of the cylinder should be cut off along the seam, after first unscrewing the valve and filling it to the top with water. Openings are cut on both sides for installing a firebox and inserting a chimney. A profile pipe is inserted and connected to a vertical channel, which is discharged through the bottom of the cylinder. Further work on the manufacture of the rocket furnace is carried out in accordance with the drawing:

At the end, the upper part must be welded into place, then carefully check all seams for permeability so that air does not flow uncontrollably into the oven. After this, you can attach a chimney with a water jacket (if available) and begin testing.

Important. To create sufficient draft, the top of the pipe must be raised above the level of the firebox to a height of 4 m.

Masonry of a rocket-type heater made of bricks

This stove option will require the purchase of fireclay bricks; ordinary ceramic bricks will not work for a rocket stove. The masonry is done using fireclay clay mortar; it is also sold as a ready-made building mixture. How to make a stationary rocket stove:

1. First you need to dig a hole, compact the bottom and pour a foundation measuring 1200 x 400 mm and 100 mm high, as shown in the photo.
   
2. After hardening, the foundation is covered with a sheet of basalt cardboard and the combustion chamber, a bunker for loading firewood and a vertical channel are laid. A door is installed at the end of the combustion chamber to clean the ash pan.
   
3. After the clay has dried, the pit is filled up, and a pre-selected pipe or small barrel with a diameter of 450 mm is placed on the vertical channel. The gap between the brickwork and the pipe walls is filled with fire-resistant insulation, for example, basalt wool, expanded clay, vermiculite.
   
4. At the last stage, a cap made of large metal barrel with a diameter of 600 mm. First, a cutout is made in its upper part and a pipe is installed to connect the chimney. When the barrel turns over, he will be at the bottom.

Then it’s a matter of technology; you can take the chimney directly outside or build another bench with smoke circulation. For this purpose, a regular one will do. ceramic brick and clay-sand mortar. The order of the brickwork of a rocket stove with a small bench is shown in detail in the video:

Conclusion

Of course, a wood-burning rocket stove is not the height of perfection and is attractive only because of its simplicity and cheapness. And fitting it into the interior of a living space is quite a challenge. This suggests the conclusion that such a heat source can be constructed somewhere in a dacha or in a temporary shelter where people do not stay permanently. The heater is not afraid of long breaks between lighting and warms up quickly enough. This unit is not suitable for heating a large residential building or bathhouse; other solutions are needed.

© When using site materials (quotes, images), the source must be indicated.

Let's say right away: rocket stove - a simple and convenient heating and cooking device using wood fuel with good but not exceptional parameters. Its popularity is explained not only by its catchy name, but moreover by the fact that it can be made with one’s own hands and not by a stove maker or even a mason; if necessary - literally in 15-20 minutes. And also because, by investing a little more work, you can get an excellent bed in your home without resorting to complex, expensive and bulky construction. Moreover, the very principle of the design of the rocket stove gives greater freedom to design and the manifestation of creative abilities, see fig.

But what is perhaps more remarkable is the “jet furnace” for the huge number of, at times, completely absurd inventions associated with it. Here, for example, are a few pearls snatched at random:

• “The principle of operation of the furnace is the same as that of the MIG-25 ramjet engine.” Yes, the MIG-25 and its descendant MIG-31 did not even sit down in the bushes near the ramjet engine (ramjet engine), as they say. The 25th and 31st are powered by double-circuit turbojet engines (turbojet engines), four of which later pulled the Tu-144 and still power other vehicles. And any stove with any jet engine (RE) is technical antipodes, see below.
• “Reverse jet thrust furnace.” Is the stove flying tail first, or what?
• “How will she blow through such a pipe?” A non-pressurized oven does not blow into the chimney. On the contrary, the chimney draws from it, using natural draft. The higher the pipe, the better the pull.
• “The rocket stove is a combination of a Dutch bell stove (sic!) with a Russian stove bench.” Firstly, there is a contradiction in the definition: a Dutch oven is a channel oven, and any bell-type oven is anything but a Dutch oven. Secondly, the bed of a Russian stove warms up completely differently than a rocket stove.

Note: in fact, the rocket stove was so nicknamed because in the wrong combustion mode (more on that later), it makes a loud whistling hum. A properly tuned rocket stove whispers or rustles.

These and similar inconsistencies, understandably, confuse and prevent you from making a rocket stove properly. So let's figure out what the truth is about the rocket stove, and how to use this truth correctly so that it really good stove showed all her strengths.

Furnace or rocket?

For complete clarity, we still need to figure out why a stove cannot be a rocket, and a rocket cannot be a stove. Any RD is the same as an internal combustion engine, only the escaping gases themselves act as pistons, connecting rods with a crank and transmission. In a piston internal combustion engine, already at the moment of combustion, the high temperature of the working fluid creates high pressure, which pushes the piston, and it moves all the mechanics. The movement of the piston is active, the working fluid pushes it to where it itself tends to expand.

When fuel is burned in the combustion chamber of the thruster, the thermal potential energy of the working fluid is immediately converted into kinetic energy, like that of a load falling from a height: since the outlet for hot gases is open to the nozzle, they rush there. In the RD, the pressure plays a subordinate role and nowhere exceeds the first tens of atmospheres; this, for any conceivable nozzle cross-section, is not enough to accelerate the migar to 2.5 M or launch a satellite into orbit. According to the law of conservation of momentum (amount of motion), the aircraft with a taxiway receives a push in the opposite direction (recoil impulse), this is jet thrust, i.e. thrust from recoil, reaction. In a turbofan engine, the second circuit creates an invisible air shell around the jet stream. As a result, the recoil impulse is, as it were, contracted in the direction of the thrust vector, so a turbofan engine is much more economical than a simple turbofan engine.

In a furnace there is no conversion of energy types into each other, therefore it is not an engine. The stove simply distributes potential thermal energy appropriately in space and time. From the point of view of the furnace, an ideal RD has an efficiency = 0%, because it only pulls due to fuel. From the point of view of the jet engine, the stove has an efficiency of 0%, it only dissipates heat and does not draw at all. On the contrary, if the pressure in the chimney rises to or above atmospheric pressure (and without this, where will the jet thrust or active force come from?), the stove will at least smoke, or even poison the residents or start a fire. The draft in the chimney is without pressurization, i.e. without external energy consumption, it is ensured due to the temperature difference along its height. Potential energy here, again, is not converted into any other energy.

Note: in a rocket thruster, fuel and oxidizer are supplied to the combustion chamber from the tanks, or they are immediately refueled into it if the thruster is powered by solid fuel. In a turbojet engine (TRE), the oxidizer - atmospheric air - is pumped into the combustion chamber by a compressor driven by a turbine in the exhaust gas flow, the rotation of which consumes some of the energy of the jet stream. In a turboprop engine (TVD), the turbine is designed so that it takes 80-90% of the jet power, which is transmitted to air propeller and compressor. In a ramjet engine (ramjet), the air supply to the combustion chamber is ensured by hypersonic speed pressure. A lot of experiments have been carried out on ramjet engines, but there have been no production aircraft with them, there are none, and there are no plans to do so, as ramjet engines are too capricious and unreliable.

Kan or not Kan?

Among the myths about the rocket stove, there are some that are not entirely absurd, and even somewhat justified. One of these misconceptions is the identification of the “racket” with the Chinese kan.

The author had the opportunity to visit the Amur region in winter, in the Blagoveshchensk region, as a child. Even then there were a lot of Chinese living in the villages there, fleeing in all directions from the cultural revolution of the Great Chairman Mao and his completely frostbitten Red Guards.

Winter in those parts is not like Moscow, frost of -40 is common. And what amazed and aroused interest in stoves in general was how Chinese fanzas were heated by canals. Firewood is transported to Russian villages by carts, and smoke comes out of the chimneys in a column. And all the same, in a hut made of logs not the size of a child’s girth, by morning the corners from the inside were frozen. And the fanza is built like a country house (see picture), the windows are covered with fish bladder or even rice paper, bunches of wood chips or twigs are placed in the can, but the room is always warm.

However, there are no subtle thermal engineering wisdom in the can. This is an ordinary, only small, kitchen stove with a lower exit into the chimney, and most of the chimney itself is a long horizontal channel, a hog, on which a stove bench is located. The chimney, for fire safety reasons, is outside the building.

The effectiveness of the can is determined primarily by the thermal curtain it creates: the couch goes around, if not the entire perimeter from the inside, except for the door, then certainly 3 walls. Which once again confirms: the design and parameters of the stove must be linked to those of the heated room.

Note: The Korean Ondol stove operates on the principle of a warm floor - a very low stove occupies almost the entire area of ​​the room.

Secondly, in the very cold, the Kans were drowned with argal - the dried droppings of ruminant animals, domestic and wild. Its calorific value is quite high, but argal burns slowly. In fact, an argal fire is already a long-burning stove.

It is not the Russian custom to keep sticking twigs into the oven, and our men disdained to cook food in cattle feces. But travelers of the past highly valued argal as a fuel; they collected it along the way and took it with them, carefully protecting it from getting wet. N. M. Przhevalsky in one of his letters stated that without argal he would not have been able to conduct his expeditions in Central Asia without losses. And the British, who disdained argal, had 1/3-1/4 of the detachments’ personnel returning to base. True, he was recruited from sepoys, Indian soldiers in English service, and pandits - spies recruited from the local population. One way or another, the highlight of the rocket stove is not at all the bed on the hog. To get to it, you will have to learn to think like an American: all the primary sources on the rocket furnace are from there, and utter speculation is generated only and only by misunderstanding.

How to deal with rockets?

With our view of things, it is necessary to study the original technical documentation of rocket stoves with caution, but not at all because of inches-millimeters, liters-gallons and the intricacies of American technical jargon. Although they also mean a lot.

Note: a textbook example is “Naked conductor runs under the carriage.” Literary translation - a naked conductor runs under the carriage. And in the original Petroleum Engineer article, this meant “Bare wire runs under the crane trolley.”

The rocket stove was invented by members of survival societies– people with a unique way of thinking, even by American standards. In addition, they were not bound by any standards and norms, but, like all Americans, they automatically always converted everything into money, taking into account their own benefit; a person with a different worldview simply will not get along in America. And instinctive self-interest inevitably gives rise to egocentrism. He by no means excludes good deeds, but not out of spiritual impulse, but with the expectation of dividends. Not in this life, so in that one.

Note: How much the average citizen of the greatest empire in history is afraid of everything can only be understood by talking to them long enough. And sociopsychologists go out of their way to convince you that living in fear is normal and even cool. The rationale is clear: intimidated biomass is easily predictable and manageable.

Without heating and cooking, of course, you cannot survive. What is a stove for? For the time being, survivors were content with camp stoves. But then, according to the Americans themselves, in 1985-86. they were greatly impressed by two films that were released with a short interval and triumphantly went around all the screens of the world: the Soviet science fiction parody of the entire human race “Kin-dza-dza” and the Hollywood “The Day After”, about the global nuclear war.

The survivors realized that after the nuclear winter there would be no extreme romance, but there would be the planet Plyuk in the Kin-dza-dza galaxy. The newly-minted plukans will have to be content with “ka-tse” in small quantities, bad, expensive and difficult to obtain. Yes, in case anyone hasn’t watched “Kin-dza-dza” - ka-tse in Plyukan style, a match, a measure of wealth, prestige and power. It was necessary to come up with your own furnace; none of the existing ones are designed for post-nuclear blast.

Americans are very often endowed with a sharp mind, but a deep mind is found as a rare exception. A completely normal US citizen with an IQ above average may sincerely not understand how it is that someone else does not get what he himself has already “caught up with” and how someone else may not like what suits him.

If an American has already understood the essence of the idea, then he brings the product to its possible perfection - what if a buyer is found, you can’t sell raw iron. But technical documentation, which looks beautiful and neat, can be drawn up extremely carelessly, or even deliberately distorted. What's wrong with this, this is my know-how. Maybe I'll sell it to someone. Either there will be a trick or not, but for now know-how costs money. In America, such an attitude to business is considered quite honest and worthy, but there, a clinical alcoholic at work as a stopper would never miss a job and wouldn’t take a couple of bolts home for the farm. That, in general, is what all of America stands for.

And Russian breadth of soul is also a double-edged sword. Most often, just from the sketch, our master immediately understands how this thing works, but in the details he turns out to be careless and overly trusting of the source code: how is it for a fellow craftsman to deceive his own man. If something isn’t there, well, it’s not necessary. It seems clear how everything is spinning there - my hands are already itching. And then, perhaps, until it comes to the hammer, chisel and accompanying literature, still counting and counting. Yes, even important points may be omitted, veiled or obviously incorrect.

Note: An American acquaintance once asked the author of this article - how did we, really stupid ones, choose the very smart Reagan as president? And you, who are really smart, tolerate a slobbering senile with dyed eyebrows in the Kremlin? True, then in America no one in a bad dream would have dreamed that in the next century a black citizen with a Muslim name would be installed in the Oval Office, and his first lady would dig up a vegetable garden near the White House and begin to grow turnips there. Times is changing, as Bob Dylan once sang for a completely different reason...

Sources of misunderstandings

There is such a thing in technology - the square-cube law. Simply, when the size of something changes, its surface area changes by the square, and its volume changes by the cube. Most often this means changing the overall dimensions of the product according to the principle of geometric similarity, i.e. You can't just keep the proportions. In relation to solid fuel stoves, the square-cube law is doubly valid, because the fuel also obeys it: it releases heat from the surface, and its reserve is contained in the volume.

Note: a consequence of the square-cube law - any specific furnace design has a certain permissible range of its size and power, within which the specified parameters are ensured.

Why, for example, can’t it be made the size of a refrigerator and with a power somewhere around 50-60 kilowatts? Because a potbelly stove, in order for it to provide any heat, must itself be heated inside to at least 400-450 degrees. And in order to warm up the volume of the refrigerator to such a temperature at a given heat transfer, you need as much firewood or coal as will not fit in it. A mini-potbelly stove will also be of no use: the heat will escape through the outer surface of the stove, which has grown relative to its volume, and the fuel will not release more of it than it can.

The square-cube law applies threefold to the rocket stove, because she is “polished” in an American professional way. With our kondachka it is better to stay away from her. For example, here in Fig. an American development, which, judging by its demand, many of our craftsmen take as a prototype.

The fact that the exact type of fire clay is not indicated here will be sorted out by ours. But, to be honest, who noticed that, judging by the absence of an external chimney and the presence of transportation holes (carrying pipe), this stove is mobile with an open firebox? And most importantly, the fact that her drum used a 20-gallon barrel with a diameter of 17 inches (431 mm with change)?

Judging by the designs from the RuNet - no one at all. They take this thing and adjust it according to the principle of geometric similarity to a domestic 200-liter barrel with a diameter of 590 mm on the outside. Many people think of setting up a ash pit, but the bunker is left open. The exact proportions of vermiculite and perlite for lining the riser and molding the furnace body (core) are not specified? We make the lining homogeneous, although from what follows it will be clear that it should consist of an insulating and accumulating part. As a result, the stove roars, it only eats dry fuel, and a lot of it, and before the end of the season it becomes covered in smoke inside.

How was the rocket stove born?

So, without science fiction and futurology, the survivors needed stove for heating a home, operating with high efficiency on low-quality random wood fuel: wet wood chips, twigs, bark. Which, in addition, will need to be reloaded without stopping the furnace. And it most likely won’t be possible to dry it in a woodshed. Heat transfer after heating is needed for at least 6 hours to get enough sleep; getting burned in your sleep on Plyuk is no better than in America. Additional conditions: the design of the furnace should not contain complex metal products, non-metallic materials and components that require production equipment for manufacturing, and the furnace itself must be accessible for construction by an unskilled worker without the use of power tools and complex technologies. Of course, no supercharging, electronics or other energy dependencies.

They immediately took a bed from the kana, but what about the fuel? For a bell-type furnace, it requires high quality. Long-burning stoves even operate on sawdust, but only dry ones, and do not allow stopping with additional loading. They were nevertheless taken as a basis; the high efficiency achieved by simple methods was very attractive. But in attempts to make “long stoves” work on bad fuel, another circumstance became clear.

What is wood gas?

High efficiency is achieved largely due to the afterburning of pyrolysis gases. Pyrolysis is the thermal decomposition of solid fuel into volatile combustible substances. As it turned out (and the survivors have their own research centers with highly qualified specialists), the pyrolysis of wood fuel, especially wet wood, continues for quite a long time in the gas phase, i.e. The pyrolysis gases that have just been released from the wood still require quite a lot of heat to form a mixture that can burn out completely. This mixture was called wood gas.

Note: in RuNet, woodgas has created further confusion, because... in American vernacular gas can mean any fuel, cf. eg gas station - gas station, gas station. When translating primary sources without knowing American technical knowledge, it turned out that woodgas is simply wood fuel.

Before that, no one had seen wood gas: in conventional stoves it is formed immediately in the firebox, due to the excess energy of flaming combustion. The designers of long-burning furnaces came to the conclusion that the primary air needs to be heated, and the exhaust gases must be retained in a significant volume over a large mass of fuel, simply by trial and error, so they also overlooked wood gas.

This was not the case when burning bundles of twigs: here the draft immediately pulled the primary pyrolysis gases into the chimney. Wood gas could have formed in it at some distance from the firebox, but by that time the primary mixture had cooled, pyrolysis stopped, and heavy radicals from the gas settled on the walls of the chimney as soot. Which quickly tightened the channel completely; Hobbyists who build rocket stoves at random are familiar with this phenomenon. But the survival researchers eventually realized what was going on, and still made the necessary stove.

Who are you, the Rocket Stove?

There is an unspoken rule in technology: if it seems that it is impossible to create a device according to the given requirements, then, smart guy, read your school textbooks. That is, go back to basics. In this case, to the basics of thermodynamics. Survivors do not suffer from sick pride; they turned to the basics. And they found the main operating principle of their furnace, which has no analogues in others: slow adiabatic afterburning of pyrolysis gases in a low flow. In long-burning furnaces, afterburning is equilibrium isothermal, requiring a large buffer volume subject to the square-cube law and an energy reserve in it. In pyrolysis gases in the afterburner expand almost adiabatically, but almost into the free volume. And now we are learning to think like an American.

How does a rocket stove work?

A diagram of the final fruit of the survivors’ labors is shown on the left side of Fig. Fuel is loaded vertically into the bunker (Fuel Magazine) and burns, gradually settling down. Air enters the combustion zone through the ash pan (Air Intake). The blower should provide excess air so that it is enough for afterburning. But not excessively, so that the cold air does not cool the primary mixture. With vertical loading of fuel and a blind hopper lid, the flame itself acts as a regulator, although not very effective: when it gets too hot, it pushes out the air.

Then things begin to become non-trivial. We need to heat up a large oven with good efficiency. The square-cube law does not allow it: the meager heat will immediately dissipate so much that pyrolysis will not reach the end, and the thermal gradient from the inside to the outside will not be enough to transfer heat into the room; everything will whistle down the pipe. This law is harmful, you can’t break it in the forehead. Okay, let's look at the basics to see if there is anything there that is beyond his control.

Well, yes, there is. The same adiabatic process, i.e. thermodynamic without heat exchange with environment. There is no heat exchange - the squares rest, and the cubes can be reduced either to a thimble or to a skyscraper.

Let's imagine a volume of gas completely isolated from everything else. Let's say energy is released in it. Then the temperature and pressure will begin to increase until the energy release stops and freeze at a new level. Great, we have completely burned the fuel, hot flue gases can be released into a heat exchanger or heat accumulator. But how to do this without technical difficulties? And most importantly, how to supply air for afterburning without violating the adiabatics?

And we will make the adiabatic process nonequilibrium. How? Let the primary gases immediately from the combustion source go into a pipe covered with high-quality insulation with a low intrinsic heat capacity (Insulation). Let’s call this pipe a fire tube or a combustion tunnel (Burn Tunnel), but we won’t sign it (know-how! If you don’t catch up, give us money for drawings and consultations! Without theory, of course. Who sells fixed capital at retail.) On the diagram, so that not accused of “opacity”, let’s denote it with flame.

Along the length of the flame tube, the adiabatic index changes (this is a nonequilibrium process): the temperature first drops slightly (wood gas is formed), then increases sharply, and the gas burns out. You can release it into the accumulator, but we forgot - what gases will be pulled through the flame tube? Supercharging means energy dependence, and there will not be an exact adiabatic, but something mixed with an isobar, i.e. efficiency will drop.

Then we will lengthen the pipe by half, maintaining the insulation, so that the heat does not go away in vain. We bend the “idle” half up, making the insulation on it weaker; We’ll think about how to preserve the heat seeping through it a little later. IN vertical pipe There will be a temperature difference in height, and, therefore, draft. And a good one: the thrust force depends on the temperature difference, and with an average temperature in the flame tube of about 1000 degrees, it is not difficult to achieve a difference of 100 at a height of about 1 m. So, while we have made a small, economical stove-stove, now we need to think about how to use its heat.

Yes, it doesn’t hurt to further encrypt it. If we call the vertical part of the flame tube a primary or internal chimney, then they will guess the main idea, but we are not the smartest in the world. Well... let's call the primary chimney the most common technical term for vertical pipelines with rising current - riser. Purely American: correct and unclear.

Now let's remember about heat transfer after heating. Those. we need a cheap, always available and very capacious heat accumulator. There is nothing to invent here; adobe (Thermal Mass) was invented by the primitives. But it is not fire-resistant, it does not hold more than 250 degrees, and at the mouth of the riser we have about 900.

It is not difficult to convert high-potential heat into medium-potential heat without losses: you need to give the gas the opportunity to expand in an isolated volume. But, if you leave the expansion adiabatic, then the volume needed is too large. This means it is material and labor intensive.

I had to go back to basics again: immediately after leaving the riser, let the gases expand at constant pressure, isobarically. This requires heat removal to the outside, about 5-10% of the thermal power, but it will not be lost and will even be useful for quickly warming up the room during the morning fire. And further along the flow of gases – cooling is isochoric (in a constant volume); Thus, almost all the heat will go into the battery.

How to do this technically? Let's cover the riser with a thin-walled iron drum (Steel Drum), which will also prevent heat loss from the riser. The “drum” turns out to be a bit high (the riser sticks out a lot), but it doesn’t matter: we will coat it 2/3 of the height with the same adobe. We attach a stove bench with a sealed chimney (Airtight Duct), external chimney(Exhaust Vent), and the oven is almost ready.

Note: The riser and the drum covering it look like a stove hood above an elongated heil. But the thermodynamics here, as we see, are completely different. It is useless to try to improve a bell-type stove by building on it - only extra material and work will go away, and the stove will not get any better.

It remains to solve the problem of cleaning the channel in the bed. To do this, the Chinese have to break down the kan from time to time and wall it up again, but we are not in the 1st century. BC. We live when kan was invented. We will install a secondary ash pit (Secondary Airtight Ash Pit) with a sealed cleaning door immediately after the drum. Due to the sharp expansion and cooling of the flue gases in it, everything in them that has not burned out immediately condenses and settles. This ensures the cleanliness of the external chimney for years.

Note: secondary cleaning will have to be opened once or twice a year, so you don’t have to bother with the hinge-latches. Let's just make a lid from a metal sheet with screws and a mineral cardboard gasket.

Small rocket

The next task of the designers was to create a small continuous combustion stove on the same principle for cooking food in the warm season. IN heating season The drum cover (Optional Cooking Surface) of a large oven is suitable for cooking; it heats up to about 400 degrees. The small rocket stove had to be portable, but it was permissible to make it with an open firebox, because When it’s warm, you can cook outdoors or under a canopy.

Here the designers took revenge on the square-cube law by making it work for themselves: they combined the fuel bunker with the blower, see fig. at the beginning of the section on the right. This cannot be done in a large furnace; precise adjustment of the furnace mode as the fuel settles (see below) will be impossible.

Here, the volume of incoming primary air (Primary Air) turns out to be small relative to the area of ​​heat release and the air can no longer cool the primary mixture until pyrolysis stops. Its supply is regulated by a slot in the hopper lid (Cover Lid). The hopper, inclined at 45 degrees, optimizes the automatic adjustment of oven power for standard culinary procedures, but it is more difficult to make.

Secondary air for afterburning wood gas in a small stove enters through additional holes in the mouth of the riser or simply leaks under the burner if a cooking vessel is placed on it. If the small stove is close to the maximum size (about 450 mm in diameter), then for complete afterburning you may need an Optional Secondary Woodgas Frame).

Note: It is impossible to supply secondary air to the mouth of the riser of a large furnace through holes in the drum (which would increase the efficiency of the furnace). Although the pressure in the entire gas and smoke path is lower than atmospheric, as it should be in a furnace, due to strong turbulence, flue gases will be emitted into the room. This is where their kinetic energy, which is harmful to the furnace, comes into play; This is perhaps the only thing that a rocket stove has in common with a jet engine.

The small rocket stove revolutionized the class of camping stoves, especially camping stoves. A wood chip stove (Bond stove in the West) will help you cook a stew or wait out a snowstorm in a one- or two-person tent, but it won’t save a group caught in a spring hike by belated bad weather. A small rocket stove is only slightly larger; it can be quickly made out of nothing, but is capable of developing power up to 7-8 kW. However, we’ll talk about rocket stoves made from just about anything later.

Also, the small rocket stove gave rise to many improvements. For example, Gabriel Apostol provided it with a separate blower and a wide bunker. The result was a stove suitable for constructing a compact and fairly powerful water heater, see the video below. The large rocket oven was also modified, we will talk about this a little at the end, but for now we will focus on more significant things.

Video: water heater based on a rocket stove designed by Gabriel Apostol

How to sink a rocket?

A rocket stove with long-burning stoves has general property:You only need to run them on a warm pipe. For a small one this is unimportant, but a large one on a cold chimney will only burn fuel in vain. Therefore, before loading standard fuel into the bunker after a long break in the firebox and kindling, a large rocket stove needs to be accelerated - fired with paper, straw, dry shavings, etc., they are placed in an open ash pit. The end of acceleration is judged by a change in the tone of the furnace hum or its subsidence. Then you can load fuel into the bunker, and it will ignite automatically from the booster fuel.

The rocket stove, unfortunately, is not one of the stoves that is completely self-adjusting to fuel quality and external conditions. At the beginning of combustion of standard fuel, the ash door or hopper lid in a small furnace is opened completely. When the stove starts to hum loudly, cover it “to the point of a whisper.” Further, during the combustion process, it is necessary to gradually cover the access of air, guided by the sound of the stove. Suddenly the air damper slammed shut for 3-5 minutes - no big deal, if you open it, the stove will light up again.

Why such difficulties? As the fuel burns, the flow of air into the combustion zone increases. When there is too much air, the furnace explodes, but do not rejoice: now the excess air cools the primary gas mixture, and the sound intensifies because the stable vortex in the riser is knocked into a chaotic lump. Pyrolysis in the gas phase is interrupted, no wood gases are formed, the furnace consumes too much fuel, and a deposit of soot cemented with bituminous particles settles in the riser. Firstly, this is a fire hazard, but most likely it won’t lead to a fire; the riser channel will quickly become completely overgrown with carbon deposits. How to clean it if you have a non-removable drum cover?

In a large furnace, a spontaneous change of mode occurs abruptly, when the top of the sticks drops to the bottom edge of the hopper, and in a small furnace - gradually, as the fuel mass settles. Since an experienced housewife does not leave her side for a long time when cooking on the stove, the designers considered it possible to combine a bunker with a blower in it for the sake of compactness.

This trick will not work with a large stove: the high riser pulls very hard, and the air gap needs to be so thin (and it also needs to be adjusted) that it is impossible to achieve a stable stove mode. It’s easier with a separate blower: it’s easier for the air to flow around the sides of a mass of fuel that is round in cross-section, and a flame that gets too hot pushes it there. The stove turns out to be self-regulating to some extent; however, within very small limits, so you still have to manipulate the blower door from time to time.

Note: It is impossible to make a bunker for a large oven for the sake of simplicity without a tight lid, as is often done. Due to the unregulated additional air flow through the fuel mass, it is unlikely to be possible to achieve stable operation of the furnace.

Materials, sizes and proportions, lining

Now let's see what a homemade rocket stove should look like from the materials available to us. Here, too, we need to be careful: not everything that is at hand in America is what we have, and vice versa.

Of what?

For a large stove with a stove bench, more or less reliable experimental data is available for products with a drum from a 55-gallon drum with a diameter of 24 inches. 55 gallons is 208-odd liters, and 24 inches is almost exactly 607 mm, so our 200-liter is quite suitable without additional conversion. While maintaining the oven parameters, the diameter of the drum can be halved, to 300 mm, which makes it possible to make it from 400-450 mm tin buckets or a household gas cylinder.

Pipes will go to the ash pit, bunker, firebox and riser different sizes, see below, round or profile. This way it will be possible to make an insulating lining of the firebox from a mixture of equal parts of stove clay and crushed fireclay, without resorting to brickwork; We’ll talk about the riser lining in more detail below. Combustion in a rocket furnace is weak, therefore the thermochemistry of gases is gentle and the thickness of the steel of all metal parts, except for the gas pipeline in the stove bench, is from 2 mm; the latter can be made from a thin-walled metal corrugated sheet, here the flue gases are already completely exhausted both in terms of chemistry and temperature.

For external coating, the best heat accumulator is adobe. If the dimensions indicated below are observed, the heat transfer of a rocket stove in adobe after combustion can reach 12 hours or more. The remaining parts (doors, covers) are made of galvanized metal, aluminum, etc., with sealing gaskets made of mineral cardboard. Conventional stove fittings are not suitable, it is difficult to ensure their tightness, and a cracked rocket stove will not work properly.

Note: It is advisable to equip the rocket stove with a view in the external chimney. Although the gas view in the high riser locks the common smoke path tightly, strong wind the outside can suck the heat out of the bed prematurely.

Dimensions and proportions

The basic calculated values ​​to which the rest are tied are the drum diameter D and its internal cross-sectional area S. Everything else, based on the size of the available iron, is determined as follows:

1. Drum height H – 1.5-2D.
2. Drum coating height – 2/3H; For the sake of design, the edge of the coating can be made oblique and curved, then 2/3H must be maintained on average.
3. The thickness of the drum coating is 1/3D.
4. Riser cross-sectional area – 4.5-6.5% of S; It's better to stay within 5-6% of S.
5. The height of the riser is the larger the better, but the gap between its edge and the drum tire must be at least 70 mm; its minimum value is determined by the viscosity of the flue gases.
6. The length of the flame tube is equal to the height of the riser.
7. The cross-sectional area of ​​the flame tube (fire duct) is equal to that of the riser. It is better to make the fire duct from a square corrugated pipe, so the furnace mode will be more stable.
8. The cross-sectional area of ​​the blower is 0.5 of its firebox and riser. A more stable furnace mode and its smooth adjustment will be provided by a rectangular corrugated pipe with sides 2:1, laid flat.
9. The volume of the secondary ash pan is from 5% of the original volume of the drum (excluding the volume of the riser) for a stove from a barrel to 10% of the same for a stove from a cylinder. Interpolation for intermediate drum sizes is linear.
10. The cross-sectional area of ​​the external chimney is 1.5-2s, where s is the cross-sectional area of ​​the riser.
11. The thickness of the adobe cushion under the external chimney is 50-70 mm; if the channel is round, it is counted from its lowest point. If the bed is on wooden floors, the pillow under the chimney can be halved.
12. The height of the coating of the stove bench above the external chimney is from 0.25D for a 600 mm drum to 0.5D for a 300 mm drum. You can do less, but then the heat transfer after heating will be shorter.
13. The height of the external chimney is from 4 m.
14. The permissible length of the gas duct in the bed - see next. section

The maximum thermal power of a rocket stove made from a barrel is approximately 25 kW, and a stove made from a gas cylinder is about 15 kW. The power can be adjusted only by the size of the fuel load. By supplying air, the oven is put into operation, and nothing more!

Note: in the original survivalist stoves, the riser cross-section was taken at 10-15% S based on very wet fuel. Then, there, in America, rocket stoves with a bungalow bench appeared, designed for air-dry fuel and more economical. In them, the riser cross-section is reduced to the recommended ones and here it is 5-6% S.

Riser lining

The efficiency of a rocket stove largely depends on the thermal insulation of the riser. But American lining materials, alas, are not available to us. In terms of reserves of high-quality refractories, the United States has no equal; there they are considered strategic raw materials and are sold even to trusted allies with caution.

From our available materials according to heating engineering, they can be replaced with light fireclay bricks of the ShL brand and ordinary self-dug river sand with a large admixture of alumina, correctly laid, see below. However, these materials are porous; in the oven they will quickly become saturated with carbon deposits. Then the oven will roar with any air supply, with all that follows. Therefore, we need to surround the riser lining with a metal shell, and the end of the lining must be covered with oven clay.

Lining diagrams for 3 types of furnaces are shown in Fig. The point here is that as the size of the drum decreases, the share of its direct heat transfer through the bottom and unlined part increases according to the square-cube law. Therefore, while maintaining the desired thermal gradient in the riser, the lining power can be reduced. This makes it possible to correspondingly increase the relative cross-section of the annular lowering of the flue gases in the drum.

For what? Firstly, the requirements for the external chimney are reduced, because The external rod now pulls better. And since it pulls better, then the permissible length of the hog in the bed drops more slowly than the size of the stove. As a result, if a stove from a barrel heats a stove bench with a length of up to 6 m, then a stove made from a cylinder is half as long - 4 m.

How to line with sand?

If the riser lining is fireclay, then the residual cavities are simply filled with construction sand. There is no need to carefully prepare a river self-dug for lining entirely from sand; just select large debris. But they pour it in layers, in 5-7 layers. Each layer is compacted and sprayed until a crust forms. Then the entire backfill is dried for a week, the top edge is covered with clay, as already mentioned, and the construction of the furnace continues.

Balloon rocket

From the above, it is clear that it is more profitable to make a rocket stove: less work, fewer unsightly parts in sight, and the stove warms up almost the same. A thermal curtain or a warm floor in Siberian frost will heat a room of 50 square meters with a power of 10-12 kW. m or more, so here, too, a balloon rocket turns out to be more profitable; a large barrel will rarely have to be launched at full power with maximum efficiency.

The craftsmen apparently understood this too; at least some. For example, here in Fig. – drawings of a balloon furnace-rocket. On the right is the original; the author seems to have wisely understood the initial developments and, in general, everything turned out right for him. On the left are the necessary improvements taking into account the use of air-dry fuel and heating the bed.

A fruitful idea is a separate supply of heated secondary air. The furnace will be more economical and the fire tube can be made shorter. The cross-sectional area of ​​its air duct is about 10% of the riser cross-section. The furnace always operates with the secondary completely open. First, the mode is set by the primary valve; Precisely adjust with the hopper lid. At the end of the firebox, the stove will roar, but here it’s not so scary; to clean the riser, the author of the design provides a removable drum cover. It, of course, must have a seal.

Rockets made from anything

Canning

Tourists, hunters and fishermen (many of them members of survival societies) soon adapted the small rocket stove into a camp stove made from empty tins. It was possible to reduce the influence of the square-cube to a minimum by using horizontal fuel supply, see the diagram on the right. True, at the cost of some inconvenience: the sticks need to be pushed inward as they burn out. But the furnace mode began to hold fast. How? Due to the automatic redistribution of air flows through the plenum and over/through the fuel. The power of a can rocket stove lies in the range of 0.5-5 kW depending on the size of the stove and is regulated by approximately three times the amount of fuel loading. The basic proportions are also simple:

• The diameter of the combustion chamber (combustion chamber) is 60-120 mm.
• The height of the combustion chamber is 3-5 times its diameter.
• The cross-section of the blower is 0.5 from its own combustion chamber.
• The thickness of the thermal insulation layer is not less than the diameter of the combustion chamber.

These proportions are very approximate: changing them by half does not prevent the stove from working, and efficiency on a hike is not so important. If the insulation is made of wet sandy loam, as described above, the joints of the parts can simply be coated with clay (left position in the figure below). Then, after 1-2 fires, the stove will acquire strength that allows it to be transported without special precautions. But in general, any of the available non-combustible materials will do the insulation, trace. two pos. A burner of any design must provide free air flow, 3rd position. A rocket stove welded from a steel sheet (right position) with sand insulation is twice as light and economical as a potbelly stove of the same power.

Brick

We will not talk about large stationary rocket furnaces: in them all the original thermodynamics are in tatters, and they are deprived of one of the main advantages of the original furnace - ease of construction. We'll tell you a little about rocket stoves made from brick, clay or stone fragments, which can be made in 5-20 minutes when you don't have tins at hand.

Here, for example (see video below), is a thermodynamically complete rocket oven made of 16 bricks laid dry. The voice acting is in English, but everything is clear even without words. A similar one can be built from fragments of brick (see figure), cobblestones, or sculpted from clay. A stove made from rich earth is enough for one time. The efficiency of all of them is not so great, the height of the combustion chamber is too small, but it is enough for pilaf or to quickly warm up.

Video: rocket stove made of 16 bricks (eng)

New material

Among the domestic developments, the Shirokov-Khramtsov rocket stove deserves attention (see figure on the right). The authors, not caring about survival in the splash, used a modern material - heat-resistant concrete, adjusting all the thermodynamics to it. The components of reinforced concrete are not cheap; a concrete mixer is needed for mixing. But its thermal conductivity is much lower than that of most other refractories. The new rocket stove began to work more stable, and it became possible to release some of the heat outside in the form of infrared radiation through heat-resistant glass. The result was a rocket stove - a fireplace.

Do rockets fly in a bathhouse?

Wouldn't a rocket stove be suitable for a sauna? It seems that you can build a heater on the drum cover. Or a flow one instead of a bed.

Unfortunately, the rocket stove is not suitable for a sauna. To get light steam, you must immediately warm up the walls with thermal (IR) radiation, and immediately, or a little later, the air, by convection. To do this, the oven must be a compact source of infrared and a convection center. Convection from a rocket furnace is distributed, and it provides little IR at all; the very principle of its design excludes significant losses due to radiation.

In conclusion: to the rocket makers

Successful designs of rocket stoves still rely more on intuition than on precise calculations. Therefore, good luck to you too! – the rocket stove is a fertile field for craftsmen with a creative streak.

close ×

The rocket stove was used by many peoples of the world long before the advent of modern home and household stoves. It served primarily to heat the home and provide warm sleeping area in the house. Cooking also played an important role. When developing the stove design, it was necessary to come up with a system that could operate with the highest possible efficiency when loading low-quality wood fuel (dry and wet).

Nowadays, it is used for heating, for cooking, and also as an interior element. You can make a rocket stove with your own hands using almost improvised materials. It all depends on its purpose and the place where it will be used.

There are many types and designs of rocket stoves - from the simplest to the multifunctional. For efficient work It is necessary to follow some rules for operating the furnace structure. There are 2 main principles of operation of a rocket stove, regardless of its configuration:

• free circulation of released gases from the fuel through the formed furnace channels, without manual drafting of the chimney;
• post-burning of pyrolysis gases released from fuel combustion under conditions of insufficient oxygen supply.

Design, characteristics and application

The rocket stove owes its unique name to the characteristic stove hum that can be heard throughout the combustion process. It vaguely resembles the sound of a rocket taking off. It is also similar to a rocket in that, during the combustion process, jet thrust is created in it. The cone-shaped shape of the stove can also be associated with the name, but this is not the main characteristic.

There are 2 types of stove designs (shown in the diagrams):

The simplest rocket oven

The simplest design of a direct combustion rocket stove consists of 2 pipes connected by an outlet - a Russian rocket stove.

The down tube is separated by a metal plate. The upper part of the pipe is approximately 2/3 of the total space where the main fuel is directly placed. The lower part serves as a primitive blower, which provides air exchange in the furnace.

The fuel filling in this case is horizontal. When laid vertically, a rocket-type furnace consists of two vertical pipes of different lengths, and a third horizontal one, which serves as a connecting channel. The latter performs the function of a firebox.

The simplest form of a jet stove is installed, usually outdoors, for the purpose of cooking food and heating water.

To make a stationary simple rocket stove made of brick, a material is used that is installed on a heat-resistant platform.

In order to achieve higher productivity, in the simplest design new elements have been added to the stoves.

The diagram shows a camping jet stove. The lower pipe is divided by a special jumper into a fuel compartment (2) and a compartment for venting air into the combustion area (3). The upper part of the furnace consists of a riser pipe, around which a heat-insulating composition (4) is laid, covered with an outer metal casing (1).

The operation of the stove is as follows: the fuel that heats the stove (straw, paper) is placed in the fuel compartment, after which the main fuel is added (chips, twigs, etc.). During active combustion, hot gases are formed, rising along the riser and escaping out. A stand for cooking utensils is installed on the cut of the pipe, taking into account a gap of 7-10 mm. Otherwise, if the required gap is not maintained, the outlet for oxygen draft will be blocked, which, in turn, raises hot gases upward. The combustion process will stop.

If the conditions for creating air draft are met, even with the combustion door closed, the combustion process will not stop. Here, the second principle of operation of a long-burning rocket furnace partially works - afterburning of pyrolysis gases in conditions of insufficient oxygen supply.

For this principle to work fully, it is necessary to provide the rocket furnace with high-quality thermal insulation of the secondary combustion chamber, because the processes of formation and combustion of gases require compliance with temperature requirements.

Improved design

This type of rocket stove, in an improved configuration, can be used at home both for cooking and for heating rooms. In addition to the fuel compartment and pipe, it has a second building, on top of which a hob is installed, and the chimney is routed to the street. You can heat a room with an area of ​​up to 50 sq.m. with such a stove.

As a result of the modernization, useful qualities and efficiency increase due to the fact that the long-burning rocket stove acquires several unique and important properties:

• Unlike the simple rocket stove design, the improved one uses a second outer casing, thermally insulating material around the combustion pipe, hermetically sealed top part housing, which creates conditions for maintaining high temperatures long time;
• an autonomous hole for supplying secondary air in a modernized furnace provides optimal air supply, while in a simple design an open firebox is used for this;
• the chimney system is designed in such a way that the heated gas flow does not rush out of the pipe immediately, but passes through the stove channels, ensuring high-quality combustion of secondary fuel, heating of the hob and uniform heat transfer of air into the room through the heated stove body.

The improved design uses additional elements, aimed at creating high heat transfer and versatility of the rocket furnace. Two principles of furnace operation are actively involved here. First, preliminary combustion of solid fuel occurs, which during combustion releases pyrolysis gases, which are used as secondary fuel.

The operating principle of a rocket furnace of this design is depicted in detail in the diagram on the left. Fuel for preliminary combustion is loaded into the fuel compartment (1). In the zone of the most active heat exchange (2), under conditions of insufficient supply of primary oxygen (A), regulated by the damper (3), pyrolysis gases are released. They rush to the end of the fire channel (5), where they burn out. Favorable conditions for gas combustion are created due to the high thermal insulation of the structure and the continuously flowing flow of secondary oxygen (B).

Then the hot gas rises up through the internal channel of the riser pipe (7) under the housing cover, which is often equipped under the cooking surface (10), due to continuous high-temperature heating. There, the gas accumulation diverges through channels located between the riser and the outer furnace body (6). Under conditions of constant heating of the housing, its walls accumulate heat, causing the air in the room to heat up. After this, the gas flow descends down the channel and then exits upward into the chimney pipe (11).

The combustion process can last several hours. For maximum heat transfer from the furnace and complete combustion of pyrolysis gases, it is necessary to maintain a consistently high temperature in the riser. To do this, it is placed in a pipe of slightly larger diameter, which is called a shell (8). The resulting space between the two pipes is tightly filled with a heat-resistant compound, for example, sifted sand, to provide thermal insulation in the pipe.

Features of operating a rocket furnace

1. Before loading the main fuel, the stove must be warmed up. This applies more to large and multifunctional rocket stoves. In them, without preheating, thermal energy will be wasted.
2. To accelerate the furnace, place dry paper in the open ashpit, wood shavings, straw. Sufficient heating of the furnace can be determined by the hum in the furnace, which subsequently subsides. Then the main fuel is placed into the heated rocket stove, which is ignited by the booster fuel.
3. At the beginning of combustion of the main fuel, the ash door is opened completely. After a while, when the stove hum appears, the vent is covered until the hum is replaced by a whisper. In the future, to assess the state of combustion of the stove, you also need to focus on the “stove sound”, opening the ash door slightly when it subsides and closing it when a hum occurs.
4. The larger the reaction furnace, the smaller the inlet opening fresh air necessary. It is advisable to use a separate blower in such a furnace.
5. The power of the furnace can be adjusted only by the volume of fuel added, but not by the air supply.
6. At self-production large rocket furnace, its bunker should be made with a tight-fitting lid, without gaps or cracks. Otherwise, stable operating conditions of the furnace will not be ensured, which can result in the consumption of excess fuel energy.
7. Contrary to popular belief, a rocket stove for a sauna is not suitable for installation, since the stove does not emit infrared radiation in sufficient quantities, which is necessary for heating the walls and transmitting convection into the air masses in a sauna. A rocket stove for a bathhouse, theoretically, can only be installed using the Shirokov-Khramtsov stove type, the characteristics of which are given below.
8. A rocket stove for a garage is a mobile version of a stove design that can quickly heat a room. The main element is a heating tank made of pipe.

Fuel types

With proper assembly and operation, a rocket stove can be fired with any type of solid fuel, wood and its waste. For example, branches, leaves, firewood, coal, corn stalks, cones, pieces of chipboard, pieces of furniture. Fuel can be loaded into the stove in either dry or raw form. This is especially true for its operation in natural conditions, where it is not always possible to find dry raw materials.

Types of rocket stoves

A rocket stove can be made independently or custom-made from various materials. Here you need to focus on the capabilities and available resources.

Gas cylinder stove

Used gas cylinder is a widely used stove material. The convenience of its use lies in the fact that it is, in fact, a ready-made blank of the furnace body of an elongated cone shape. Fuel costs are minimal, and the heat generated will heat a room of up to 50 sq.m. The cylinder material must be selected that is non-explosive and resistant to high temperatures and heating. The best option is a solid metal propane cylinder with a capacity of 50 liters, a diameter of 35 cm and a height of 85 cm. This volume is enough to burn any type of fuel.

Also, for the manufacture of a portable rocket stove from a gas cylinder, volumes of 12 and 27 liters are used, but with less heat transfer. The cylinder can be purchased at a special gas station.

Before starting the manufacture of the furnace, the gas is released from the cylinder by opening the valve for a while. Then, a simple potbelly stove is made. Next, the upper part of the cylinder is cut off, leaving the hole for the valve. The top is cut out round hole with a welded steel strip that serves as the basis for the chimney.

Brick oven

It can be either stationary or traveling. A rocket stove made hastily, in 15-20 minutes, made of bricks, broken bricks or cobblestones “on dry ground” will do an excellent job of cooking food and heating water. The disadvantage of such a stove is low fuel economy and low heat output. Heating the bricks in the chimney to 1000 degrees allows the structure to quickly enter operating mode. At the same time, the rocket does not smoke due to the fact that at this temperature all the fuel burns without residue.

Water-jacketed rocket stove

The most commonly used is the stationary oven type. The peculiarity of such a stove is that heat transfer is used not only to heat the air in the room, but also to heat the water. To do this, a rocket stove with a water circuit is connected to a heat storage tank to create a system autonomous water supply. Perfect option for use in the country or in private water, because the device helps reduce heating and water heating costs, which is very economical.

Barrel stove

A common model for heating a home. Low-cost to manufacture and energy-intensive in heat transfer. Often equipped together with a warm bed. Capable of heating a room of more than 50 square meters. m. A standard 200-liter barrel with a diameter of 607 mm is perfect for making a stove. This diameter can be reduced by almost half, which is convenient for installing a riser pipe made from a gas cylinder or tin buckets with a diameter of 300-400 mm. In short, the stove can be built from scrap materials.

Shirokov-Khramtsov furnace

Domestic modernization of the rocket furnace. The main material is heat-resistant concrete, which creates excellent thermodynamics in the structure. Due to the stable operation of the furnace and the low thermal conductivity of the material, part of the heat comes out in the form of infrared radiation, which is impossible when using other types of furnace. If you use heat-resistant glass, the stove can be converted into a fireplace. The disadvantage of installing such a furnace is the high cost of the material, the preparation of which will require a concrete mixer.

Stove-oven

For cooking and preparations at home and outdoors, an improved stove design with a wide cooking surface for installing several containers is installed. A vertical riser pipe with a firebox welded to it is located directly under hob, providing its high-temperature heating. Accumulating under the panel cover, the gases exit through a horizontal pipe, uniformly heating the entire area of ​​the panel, and rush to the exit through a vertical chimney channel.

How to make it yourself

Let's take a closer look at making a do-it-yourself rocket stove with a stove bench. Its design is more cumbersome and installation is more difficult than the types of stoves listed above, but thanks to step-by-step instructions and diagrams, building it yourself will not be difficult. The main thing is to follow all installation recommendations.

Step-by-step instructions on how to make a rocket stove:

• First, make a 10 cm deepening for installing the fuel compartment, lining it with bricks made of fireclay clay. Then you need to install the formwork along the structure line. For a stronger foundation, you can use construction reinforcement or mesh, laying it on a brick base.
• Using a level, lay out the base for the combustion chamber.
• Then you need to fill the structure with concrete and let it dry for 24 hours. After the solution has set, you can continue building the furnace.

• Lay out the base of the stove, laying the bricks in a continuous pattern.
• Form the side walls by laying several rows of masonry.
• Arrange the lower channel of the rocket, taking into account the order.
• Then you need to lay a series of transverse bricks so that the riser pipe and combustion chamber remain open, and the combustion chamber remains hidden.

• You need to take the body of the old boiler and cut it on both sides so that you end up with a pipe that is wide in diameter.
• A flange is installed in the lower part of the housing from under fuel and lubricants, into which a horizontal heat exchanger pipe will be installed. In order to maintain the tightness and safety of the product, it is necessary to provide for the use of continuous welds in the work.

• After this, the outlet pipe cuts into the barrel. The barrel is cleaned from rust, covered with a primer and several layers of heat-resistant paint.
• A side branch must be welded to a horizontal chimney to form an ash pan. To facilitate its cleaning, when operating the furnace, the channel must be equipped with a sealed flange.
• Next, a fire pipe is laid out of refractory bricks, maintaining dimensions of 18x18 cm square. When laying out the internal channel, it is important to maintain strict verticality for stable operation of the furnace. To do this, you can use a body kit or a level.

• It is necessary to put a casing on the flame tube, and place perlite balls in the resulting space. The lower part of the riser must be hermetically sealed with a clay mixture to prevent spillage of the thermal insulation.
• Then the fuel cap is made using a previously cut part from the boiler. For convenience, you can weld a handle to the lid.
• Mix the clay solution with sawdust (prevent the product from cracking), up to 50% of the total volume. The result is the so-called “adobe grease”, which needs to be coated with the appearance of the resulting structure to mask unsightly parts and increase thermal insulation.

• Next, the appearance of the furnace is formed. The furnace circuit is laid out. For this you can use different materials: stone, brick, sandbags. Interior is filled with crushed stone, and the top one is covered with adobe mixture.
• A 200-liter barrel, which serves as the outer shell of the furnace, is installed on a previously prepared base. Be sure to install the barrel so that the lower pipe is on the side of the stove bench. Further Bottom part covered with clay for sealing.
• Then you need to form a channel from a corrugated pipe to supply air from the street and bring it to the fuel compartment. Without installing such a channel, a DIY rocket stove will consume warm air from the room during operation.

• After the construction of the main part of the stove structure, training kindling is carried out to check the free removal of gases through the horizontal chimney.
• The heat exchanger pipes are connected to the lower pipe, installed on a red brick base.
• Next, you need to install the chimney pipe yourself, hermetically sealing all connections with asbestos cord or fire-resistant coating.
• At the end, the bed needs to be shaped in the same way as before - when forming the main body. If you leave the barrel open, without masking it with adobe, then the heat during combustion will immediately enter the room. If the barrel is completely covered with adobe, leaving the lid intact, then heat will accumulate in the body, which will create excellent conditions for cooking on the hob.

Instead of a barrel, you can use a gas cylinder (a rocket stove made from a gas cylinder), and instead of a boiler, pipes and tin buckets adjusted to the shape. When creating a rocket stove with your own hands, it is very important to maintain accuracy and proportionality in size using drawings. This will guarantee long and efficient operation of the long-burning stove with your own hands.

The advantages of using homemade rocket stoves in everyday life are significant. The construction of a furnace does not require large economic costs (for materials, heating) and time (it takes a maximum of 3-4 days to manufacture a furnace).

High performance and heat transfer with unpretentious fuel loading are ideal. You can decorate the stove in any way you like, thereby adding a new interior element to your home.

Some sources claim that the rocket stove got its name due to the special sound it makes during use. Let's make a reservation right away - a strong hum is heard only during kindling, and then, a properly built stove should not hum. The sound that you can hear from a well-built structure will be more reminiscent of a rustle, a whisper, but nothing like the sound of a rocket taking off.

The efficiency of the furnace is increased due to the design features, which allow the use of not only the thermal energy obtained as a result of fuel combustion, but also the additional part of the heat generated during the afterburning of pyrolysis gas.

Attention! This gas is formed during the combustion of wood. Its ignition is possible only at a sufficient temperature level. With a large supply of oxygen or in an unheated furnace, such gases cool, do not ignite and evaporate freely.

Of course, the rocket stove is easy to manufacture, easy to use, practical, and not demanding on the quality of wood fuel. However, its operation depends on the correctness of the calculations and the accuracy of the manufacturing of the entire structure.

The general diagram of the furnace structure is as follows:

• Despite the simplicity of the design, an ultra-efficient long-burning rocket stove requires precise adherence to the proportions of its parts:
• The diameter of the chimney is not less than the diameter of the fuel bunker;
• The length of the horizontal compartment of the combustion zone is no more than half of the vertical expanding section;
• The height of the fuel bunker is equal to the length of the horizontal section;
• The length of the chimney is 6-10 times greater than the height of the vertical secondary combustion chamber.
• Thermal insulating adobe coating of the stove bench is at least 2/3 of the height, at least 15 cm above the chimney pipe.

Principle of operation

Fuel is loaded into a vertical bunker. With the correct design of the rocket furnace, the fuel burns only in the lower part, gradually settling under its own weight. Combustion in the primary combustion chamber is supported by suitable oxygen penetrating with the air flow through the ash pan. Then the fuel gases move freely into the afterburning zone, ignite as a result of the pyrolysis reaction, and heat the secondary combustion chamber and the bell. Due to the temperature difference in the primary combustion chambers and the vertical hood, draft is created, and hot air passes into the chimney channel. The exhaust system for combustion products consists of an internal part (heating the home) and an external part (removing smoke and gas from the room to the outside).

During operation, the fuel burns almost 100%, leaving only water and carbon dioxide at the exit. The long chimney provides almost complete cooling, so water can flow from the pipe. And as a result, it is not required tall pipe, most often it is removed simply by continuing the horizontal section through the wall.

A rocket stove can be used simultaneously as a means of cooking and heating a small room. Design features allow the surface of the hood to be heated up to 400°C; this section of the stove is used as a cooking surface, and the long chimney most often turns into a lounger that can give off heat for up to 12 hours after heating. The effect of a heat accumulator increases with properly lining (coating) of the chimney body.

This is interesting! The principle of a jet stove without a heat-storing casing is used in small, portable camping structures. This type of stove uses only the energy generated by direct combustion. In this case, the amount of fuel burned increases, and the efficiency of the stove decreases significantly, but it is quite enough for cooking and heating the tent.

DIY rocket stove

When making a rocket stove with your own hands, you will need the following materials:

• For a large-volume furnace - barrels of fuels and lubricants with a volume of 200 liters and a diameter of 600 mm. For the outer body of a medium-sized oven, gas cylinders with a diameter of 300 mm are used (it is also possible to use tin buckets, 400-450 mm);
• For the fire duct of a furnace based on a barrel of fuel and lubricants, a 135 mm steel round or profile pipe (120x120 mm) is prepared. For a furnace with an outer casing made of a gas cylinder, round pipes of 70 mm or profile pipes of 70 and 150 mm are used;
• The entire structure is made of tin or thin sheet steel 2-3 mm thick. (Thinner sheet metal can only be used for chimney installations).
• Thermal insulating gaskets made of mineral cardboard;
• For the chimney - corrugated pipe. The diameter of the pipe should be one and a half times the diameter of the fire pipeline;
• Fireproof brick, fireclay scrap, clay, sand. Straw (for adobe);
• Fittings for the stove (doors of the firebox and ash pan). A mandatory requirement is integrity and tightness, which is ensured by gaskets made of mineral cardboard.

Advantages and disadvantages

The main advantage - ease of installation - has already been mentioned by us, however, this type of stove has gained popularity due to an additional number of features.

1. Firewood and wood of any quality and condition can be used as fuel. Of course, the combustion reaction of the pyrolysis gases of raw wood will require a high temperature, but even in this case, as a result of the primary combustion of fuel, thermal energy will be released, which is sufficient for boiling water and cooking;
2. Despite the simplicity of the design, the thermal output of which a rocket oven made on the basis of a barrel of fuel and lubricants is capable of can reach 18 kW. These parameters are enough to heat a room up to 20 m². A small stove (based on a gas cylinder), subject to all installation and installation rules, can have a power of up to 10 kW.
3. A well-heated jet stove can retain heat for a long time, for half a day (up to 12 hours) without requiring additional flooding.

However, some disadvantages of structures of this type cannot be mentioned:

1. Some types of rocket stoves cannot be used to heat water and then feed it into radiators or into the hot water supply system, because. in principle, the connection of additional heat exchangers (coils) breaks the tightness of the internal bunker, or reduces its thermal insulation characteristics, which makes it impossible to use the technology of afterburning pyrolysis gases;
2. General adjustment of the stove operation is possible only by reducing or increasing the amount of firewood. The blower, which regulates the air flow, is used only for primary ignition.
3. The rocket stove is not a fast-acting design. (On the contrary, it requires quite a long preparatory time for kindling and heating its own body and takes just as long to cool down). Therefore, such a design cannot be used in garages and bathhouses.

Video