How to adjust a double-glazed window on a balcony door. How to properly adjust a plastic door on a balcony

Reading time ≈ 4 minutes

Long-term use of a plastic balcony door leads to imbalance of its mechanisms. As a result, the door closes poorly or stops closing altogether. You can correct the situation by contacting the company that installed it. However, it is not always possible for a specialist to come to you after an application; as a rule, you have to wait several days. If time is pressing, you can do the work yourself. After all, adjusting a plastic balcony door does not cause much difficulty.

The balcony door can be adjusted in several directions:

• vertically;
• horizontally;
• sash pressure adjustment.

Vertical adjustment

To eliminate sagging, which does not allow the door to tilt back and leads to the threshold touching when opening or closing, it is necessary to adjust the sash in height, that is, move it up. Work is carried out with the lower loop.

1. First, release the loop itself from the cap.
2. Insert a screwdriver into the hole in the upper end of the hinge and turn the adjusting screw clockwise to raise the door. If it needs to be lowered, then the rotation is made counterclockwise. Usually 2-3 turns are enough. In the video you can see how to do it correctly.

If such adjustment of plastic balcony doors is carried out independently, then after each stage it is necessary to carry out a check to make sure that everything was done correctly. The shutter should move freely, there should be no problems when opening, and when closing it should close without interference, but tightly.

We must remember that not all windows and PVC doors The adjustment holes are made for a hexagon. Sometimes you need to use a key - an asterisk, you can see what it looks like in the photo. It is advisable to purchase such a key in advance, and if you need to adjust the plastic balcony doors yourself, it can be done using this device.

Horizontal adjustment

When temperature fluctuates, deformations may occur that prevent the balcony door from closing. The sash simply rests against the mechanism and does not go further. By using mechanical pressure on the door, it will be able to close. But the use of force when opening or closing doors is undesirable, as this provokes further deformation.

To eliminate this problem, the plastic balcony door, namely its hinges, is adjusted. To adjust, you will need an H4 hexagon.

1. The end of the screwdriver is inserted into the side adjustment screw, which is accessible from the lower side surface of the lower hinge.
2. The screw begins to be tightened to tighten the sash to the hinge.

So the sash can be shifted to the right - to the left by a distance of up to 1 cm. If this is not enough, then you need to repeat all the steps with the top hinge. If the adjustment of the PVC balcony door is carried out correctly, the door will close freely, without interference.

Adjusting the pressure of the balcony door

To prevent the door from letting in cold air from the street, the pressure on the balcony door is adjusted. To do this, use the locking elements on the sash. Usually they are made in quantities of 4 pieces. Almost always, the adjusting clamping screws are designed as eccentrics, that is, the hole for the hexagon has some offset from the center and its rotation allows for displacement in both directions, obtaining the optimal level of clamping. By turning such an eccentric, you can either strengthen the pressure or weaken it.

Sometimes the clamping screws have a different design. If the screws go through a special hole, then in the central position the pressure will be minimal. Moving around the axis will change the level of pressure. Therefore, in order not to make a mistake with the method of adjusting the pressure, before starting work, you need to familiarize yourself with the hardware features of the door that is installed on your window manufacturer’s website.

To check whether the adjustment has been carried out correctly, you need to close the door by inserting under top part fold a sheet of thick paper or a banknote. The correct level of pressure is indicated by the tightness of the bill being clamped by the flap; it should be held in the place where it was clamped and pulled out only after applying some effort. Using this simple technique, you should check the entire perimeter. If the paper holds well everywhere, it means everything was done correctly, and winter winds and drafts are not a problem.

Adjustment of plastic doors should be carried out approximately once a year. Timely correction of the position of the sash in the opening will help avoid its irreversible deformation and extend the service life of the entire structure.

Video of adjusting a plastic balcony door

In each modern apartment Plastic doors to the balcony have been installed. They are distinguished by many advantages: ease of use, low maintenance and speed of installation. Possible problem, which occurs after long-term operation of the mechanism - misalignment and loose fit of the sash. Therefore, it is useful to know how to adjust the plastic balcony door to eliminate loosening due to regular opening, closing and ventilation.

Before you begin diagnosing the problems that have arisen and subsequent repairs, it is worth understanding the structure. There is a base unit, as well as spare parts for a plastic balcony door. Moreover, among the accessories there are both irreplaceable and optional parts. As a rule, in door block includes the following elements:

• frame made of PVC profiles, which are connected by special fasteners;
• a leaf assembled according to a principle similar to a door frame;
• hinges, thanks to which the structure closes and opens;
• handle and latch for PVC balcony doors;
• a seal that ensures the tightness of the sash closure;
• double-glazed balcony door.

In addition, the device may include additional elements, expanding the functionality of the balcony door: stoppers, mechanical or hydraulic sensors and other parts.

The design of the handle may also differ: it can be stationary or movable, one-sided or two-sided; shell handles for balcony doors are popular. The latter option is in demand in families with children, as well as among smokers, because the shell handle allows you to conveniently close the door while on the balcony. For an apartment on the ground floor, a good idea is a handle with a lock - a balcony latch for plastic doors, which allows you to secure the balcony from intruders.

When adjustment of a plastic balcony door is required

The price of a plastic balcony door is quite high, but buying an expensive high-quality model does not save you from frequent cases of mechanism breakdowns. It's all about its frequent use, which leads to a decrease in the tightness of the sash.

In addition, double glazing provides excellent sound insulation, and PVC guarantees durability. However, it is these materials that noticeably make the structure heavier, as a result of which it begins to sag under own weight and stops closing tightly. As a result, a noticeable draft appears in the room, and insulating the balcony does not help.

The normal position of the plastic door is as follows:

• if the door is open, it does not move on its own;
• no sash displacement;
• the sash is pressed tightly to the profile door frame.

If this is the case, intervention in door mechanism not required. However, if you notice the slightest deviation, you immediately need repairs to your plastic balcony doors. You shouldn’t delay calling a repairman, because with every opening and closing the situation will get worse. As a result, this can lead to balcony doors not closing at all.

Helpful advice! If the warranty for installing the door has expired and you do not want to contact a specialist, you can watch a video of self-adjustment of plastic balcony doors and fix the problem yourself.

Types of balcony door faults

If you adjust a plastic balcony door with your own hands, for the success of the repair it is important to determine the causes of the malfunction. Most often the problems are as follows:

To test the door for tight closure, slam the shutter with a regular album sheet paper. Try to push the sheet around the perimeter of the door. If it moves easily, the structure has lost its density and needs adjustment.

Also evaluate the tightness of the seal: uneven pressure on the rubber usually indicates sagging. Determining the direction of displacement is simple: pay attention to the place where the seal is compressed and check whether there is a mark from the sash on it.

How to determine if a door leaf is skewed

If you suspect the structure is skewed, close the sash and then move around the perimeter closed door with a simple pencil. Open the door and compare its outline with the drawn line. The presence of unevenness indicates that the door is warped. For accurate results, use a building level.

Let's say, as a result of measurements, you find out that the width of the drawn strip is 8 mm (an error of 1 mm is permissible). This means everything is in order and the door is not warped. If the width of one strip is 12 mm and the other is 4 mm, this clearly indicates that the door is skewed by 4 mm.

Note! Sometimes it turns out that on the hinge side the width of the strip is 3-4 mm, and on the handle side 6-7 mm. Such indicators indicate that the door is narrowed by 4-6 mm - this is a manufacturing defect, and it makes no sense to move such a door.

Also check the width of the opening on all sides of the frame. The difference in measurements should not be more than 1 mm. Otherwise, the opening will have the shape of a barrel - this happens when installed incorrectly, when the middle of the frame is pulled towards the wall more than the top and bottom. Such errors also lead to loose clamping. By measuring the width of the sash on all sides, you will determine the correct length of the impost. The difference between the three measurements should not be more than 0.5-1 mm. If the indicators differ from the norm, the length of the impost differs from the required one and causes the door to skew.

How to adjust a plastic balcony door: step-by-step instructions

To avoid mistakes or accidental damage to the glass unit of a balcony door (the cost of which is quite high), you need to figure out how to adjust plastic balcony doors correctly. When carrying out work, it is not necessary to overpay for a specialist: you can adjust the balcony door yourself - video instructions can be easily found on the Internet.

To work you will need very few tools:

• hexagon;
• crosshead screwdriver;
• flat screwdriver.

Instructions and video: how to adjust plastic balcony doors when sagging

If you notice that when opening and closing the door it scratches the bottom edge of the frame, this indicates sagging of the door. Adjustment in in this case can be vertical or horizontal.

Horizontal adjustment steps:

1. Open the door wide to the swing position.
2. There is a screw located near the top hinge at the end of the sash. Take the hex key and turn it clockwise 2-3 times.
3. Remove the plugs covering the holes leading to the top screws.
4. Turn all screws under the plugs clockwise.
5. After adjusting the mechanism, check whether the door now closes freely. If necessary, tighten the screws again.

To understand how to adjust balcony doors vertically, do the following:

1. Lift the door evenly and find the screw at the bottom end of the hinge, located along its axis.
2. If the screw is covered by a plug, carefully remove it.
3. If you twist the screw clockwise, carefully lift the door, if counterclockwise, lower it.

Adjusting the pressure of balcony doors and door handles

To tighten the handle for a plastic balcony door, you need to do the following:

1. Slowly and carefully turn the plastic cap at a right angle.
2. Under plastic cover find screws for fastening. Pull them up.

If the handle does not turn well, sometimes it is enough to lubricate the lock with a special material that does not contain resin or acid. In the event of a complete breakdown, you should buy a handle for plastic balcony doors, unscrew the screws, remove old part and put a new one in its place.

Helpful advice! A good option is to install a magnetic latch on the balcony door. This will help avoid too frequent exposure to door handle every time the door is closed and opened, which will have a beneficial effect on its durability.

If there is blowing from plastic balcony doors, this is a sure sign that the sash is not pressed tightly. It is necessary to adjust the pressure of the plastic balcony door. To figure out how to adjust plastic balcony doors for pressure, look for locking elements on the door leaf. They are responsible for the pressure density.

Using a wrench or pliers, rotate the locking elements until the door is in the desired position. Professionals recommend periodically self-adjusting plastic balcony doors depending on the season. Just figure out how to adjust plastic balcony doors for the winter, and you can easily loosen the pressure in hot weather and tighten it in the cold season.

Sometimes adjusting the hinges does not help solve the problem, and then the leakage of the clamp can be eliminated using a pin. For this you will need. To achieve maximum door pressure, install the trunnion perpendicular to the profile. To, on the contrary, achieve minimal pressure, position the trunnion parallel.

Replacing the seal and adjusting the door when the frame is scratched

It may turn out that adjusting the door pressure did not bring the desired result. This happens because rubber compressor worn out, and any door adjustments are pointless without replacing it. To do this you need:

1. Pull out the old tires. This is done without special effort And additional tools you won't need it.
2. Remove dirt from the inside of the groove.
3. Place a new seal. Make sure that the side bend is at the end of the sash.

Helpful advice! To make work easier, remove the sash from the frame: this will allow access to the rubber gaskets from the hinge side. It is better to choose a seal from the same manufacturer as the installed doors.

If the balcony doors do not close well and touch the frame, scratching its center, follow these instructions for self-adjusting plastic balcony doors:

1. Lower the sash to the bottom hinge.
2. Insert the adjusting key into the side screw and tighten the sash.
3. If the door position does not return to normal, repeat the procedure with the top hinge.

If it is blowing from the side of the balcony, or the door opens and closes poorly, the problem is not necessarily the quality of the door or unscrupulous installation. Often the situation can be corrected with adjustments. How is a plastic balcony door adjusted?

If the warranty period has not yet expired, you can call a technician from your installer. Moreover, the installers were required to adjust the door upon completion of the installation. But someday the warranty will end, and you will still have to adjust the door yourself if you do not want to spend extra money on it. Doors become out of adjustment much faster than windows: they weigh more and are opened and closed more often.

Important: new houses shrink during the first year. During this period, you need to watch the door. If neglected, the structure may become deformed.

A well-installed and adjusted door:

Presses tightly and evenly around the entire perimeter;

There are no visible distortions or deviations from the vertical;

Stable in open position(in the absence of wind).

Video “Adjusting plastic balcony doors”:

The condition of the clamp is checked using a sheet of paper. The sheet is placed between the sash and the frame, the door is locked, and the paper is pulled out. It should come out with some effort.

You can identify uneven installations (the canvas is poorly aligned with the frame) using a simple pencil. You need to trace the perimeter of the locked door, open it and see how parallel the drawn line is to the edge of the frame.

Adjustment of a plastic balcony door is also necessary if: the handle does not turn well, the seal is unevenly deformed. If it is deformed at the bottom, the door must be raised by adjusting the bottom hinge; if at the top, lower it a little by adjusting the top one.

Instructions

Required set of tools:

Hex keys of different sizes;

Pliers;

Screwdrivers, slotted and cross;

Roulette.

There are three hinges on the door, which have adjusting screws. Adjusting the plastic balcony door is done as follows:

1. Open the door, unscrew the screws securing decorative overlays, hexagon 3.

2. Close the door, remove the trim.

3. Under the cover there is a screw located horizontally. With its help, the door is adjusted horizontally. To raise bottom corner sash, you need to tighten the screws in two hinges, top and middle.

4. If there is a need to move the canvas completely to the right/left, you need to adjust all three hinges with horizontal screws.

5. To adjust the plastic balcony door vertically (raise/lower), screws are used lower parts loops and a 5.2 hex key. The door is lowered by turning the screw clockwise. In the opposite direction it rises.

6. You can move the lower corner to the right/left by tightening the same screw on the lower hinge.

7. To adjust the top or bottom striker, use a 2.5 hex key.

8. The locking plate can be tightened with a Phillips screwdriver.

9. To adjust the pressure, use a special pin on the fittings. It is turned with pliers. To reduce the pressure, the trunnion is turned parallel to the profile (this is the extreme position); to increase it, it is turned across.

10. In other models there is no pin fitting; the plastic balcony door is adjusted on the strike plate. In this case, you need to insert a hex key into the groove on the bar and make about half a turn.

Perfect and precise design metal-plastic door, but it also begins to function poorly. In case of wooden doors In addition to the hinges, this can be caused by deformation of the door leaf or frame itself; plastic doors begin to “act up” solely due to a malfunction of the mechanism. How to adjust plastic door with our own hands, let’s look into it in detail.

Possible problems

A normally installed and functioning door should open and close easily, not rub against the frame, and the connection should be uniform around the perimeter. Opened door in the absence of drafts, it should be in a stable position.

The clamping mechanism must “bring” the door without a gap between it and the frame. It’s easy to check - a sheet of paper sandwiched between the door ledge and the frame should be pulled out along the entire length of the door ledge with some effort.
Failure to satisfy any condition means that the geometry is broken.

The plastic balcony door has sagged or the sash has shifted relative to the frame. All defects can be corrected by adjusting the fittings.

If the warranty period has not yet expired

then this should be done by the service department of the company that installed the door. Otherwise, you can call a specialist. But that's what's good about it modern designs, that if there are instructions, self-adjustment The installation of plastic doors is quite feasible for anyone and requires a minimum set of tools - hex keys, screwdrivers and pliers.

This article discusses the most common cases of adjusting swing plastic entrance (interior) and balcony doors.

Pendulum or sliding systems have their own methods.

Adjusting a plastic door with three hinges: entrance

Entrance doors differ from interior ones in the thickness of the profile and glass unit, but their hinges are similar. And the differences from balconies are more significant. This is both the type of hinges and the lack of a folding mechanism (for ventilation). Let's figure out how to adjust a plastic door with three hinges yourself.

Typically, such doors have three hinges installed - top and bottom, and the third can stand next to the top or in the middle of the leaf. In principle, this is the usual arrangement and number of hinges so that they normally “support” the weight of the door. Differences may be in the design of the loop and the clamping mechanism, and therefore in the adjustment.

Overlay door hinge (type greenteQ TB 100.ZD.K)

This loop with decorative strip and the ability to adjust in three planes.

Horizontal and vertical displacement occurs using two screws, and the pressure is adjusted using a screw and a bar between the hinge and the box.

1. To adjust skew:

To adjust plastic doors relative to the vertical axis horizontally (right-left), it is necessary to remove the decorative strip on the hinge installed on the door leaf. First, you need to open the door and unscrew the screw that holds this bar. Then the door is closed and the bar is removed. Under it there are 6 fastening screws for a screwdriver (perpendicular to the blade) and one adjusting screw for a hexagon - parallel to the blade towards the hinge.

By screwing it in or out, you can adjust the displacement of the door relative to the vertical by 5 mm in each direction along the X axis.

2. To raise (and even lower)

the sash uses a key-adjusting screw located at the lower end of the hinge. It is covered with another decorative strip, which simply “unfastens”.

They can raise the door by 4 mm or lower it by 1 mm, relative to the factory setting along the Y axis.

3.Adjustment of the plastic door: fine adjustment of the pressure

(within 1.5 mm) is carried out using a screw located at the upper end of the loop.

For a “rough” adjustment, you need to remove the door from its hinges, and then the part of the hinge that is installed on the frame. It is attached to it through strips, which can have a thickness from 1 mm to 5 mm. In this way, you can further adjust the door pressure (along the Z axis).

Door hinge type WX

has horizontal adjustment up to 6.2 mm, vertical adjustment up to 4 mm, the clamp can be adjusted with a screw up to 1.8 mm (if necessary, the clamp can be improved with additional bushings at the place where the hinge is attached to the box).

1. Horizontal adjustment occurs using a side screw located under the decorative trim on a hinge that is attached to the door. First, you need to unscrew the screw that secures the position of the hinge relative to the “0” level. It is located in the body of the hinge and runs parallel to the door leaf. Then you need to unscrew the screw that locks the outer decorative body of the hinge; by moving it, you can gain access to the adjusting screw.

With its help, you can shift the position of the sash to the right or left.

2. The pressure adjustment takes place on the mating part of the hinge (attached to the door frame). It is necessary to remove the decorative cap from the end of the loop. Under it you can see an eccentric with slots.

In order to release it, you need to unscrew the locking screw (it is located on the side of the hinge body on the door side). Then, using a special key inserted into the slots of the eccentric, you need to turn it to the required angle and lock it. This way you can strengthen or weaken the pressure.

You can use a regular plate or a wide flat-head screwdriver, but the vertical adjustment screw will get in the way. In this case, it must be completely unscrewed.

3. Vertical adjustment is carried out using a screw screwed into the loop from below, through a pressure adjustment eccentric.

How to adjust a plastic balcony door

Adjustment of plastic doors follows the same algorithm as for plastic window. Each manufacturer's fittings may have differences in adjustment methods, but in many respects they are similar.

Adjustment of plastic doors horizontally (X-axis) to the right or left can be done using two screws in the lower and upper hinge (depending on which part of the door is “rubbed”).

Both screws are visible when the sash is open. The lower one is located in the hinge support part on the box.

The upper one is located in the opposite part of the hinge on the sash.

By tightening or unscrewing the screw, you can move the sash away from the frame or towards it.

Vertical adjustment (Y axis) is carried out using a screw located in the lower loop behind the decorative strip, with outside doors on the leaf itself.

It is located at the end. By screwing it in or out, the door is raised or lowered.

The pressure is adjusted by turning the eccentrics located at the vertical end of the door leaf.

First you need to find out in which part the clamp is too loose or too strong. The eccentrics “work” in tandem with the locking plates on the box. If the eccentric is located along the sash - the pressure is minimal, perpendicular - maximum. Turn the eccentric using pliers.

Another type of door pressure adjustment occurs not with the help of eccentrics, but with the help of a locking pin at the end of the leaf.

It has a hole for a hex key and a control point (risk). Depending on the position of this point, the pressure can be stronger or weaker. Adjusting plastic doors and very similar.

There is a third type of pressure adjustment, which occurs using a counter (locking) plate located on the box itself. It can move relative to the frame, thereby strengthening and weakening the connection of the door.

In addition, you can adjust the plastic balcony door not only from the side of the hinges and eccentrics, but also from the side of the folding mechanism.

First you need to fold back the open sash

But the mechanism itself does not allow you to turn the handle up when the sash is open. To remove the handle fixation, you need to press the “tongue” (flag, clip) at the end of the door, in the area of ​​the handle itself.

It may look different, but its operating principle is the same - in closed the sash presses it and unlocks the handle, which can be turned up, setting the door for ventilation. If you open the door and press the “tongue” with your hand, then the door in this state can be folded back at the top. But at the same time, it is better to keep it suspended - after all, it will stay down at one point on the lower loop.

Will open inner part the mechanism of the upper fittings (usually the door “closes” it). There will be one (or two) eccentrics with hexagon adjustment screws.

Using them you can press (or press out) the door in the area of ​​the hinges.

By squeezing the “tongue”, the door is returned to a vertical state, after which the door can be closed.

These are the main methods for adjusting mechanisms different types doors.

Information to note : .

Adjusting plastic doors yourself video.

Many owners plastic time From time to time they are faced with the following problem: how to adjust the plastic balcony door. In this case, the structure may not close tightly, the handle or hinges may become loose. Regulatory process door device is not difficult. You can tighten and adjust the fittings in a few minutes.

They will help you design an exit to the balcony in a practical and convenient way. plastic structures

Read in the article

Features of the design of the balcony door

PVC products are suitable option For . Such designs are characterized by resistance to temperature changes and influence. Such products are light in weight and do not become a burden to exposure to moisture and temperature changes. When creating plastic doors, the same profile is used as when installing.

Plastic products have certain advantages:

• thanks to the multi-chamber profile, they retain heat excellently and have good quality;
• are distinguished by their immunity to any manifestations of the external environment;
• are environmentally friendly and durable;
• characterized by ease of care.

Most often for balcony structures glass top and plastic bottom are used. If there is a strong frame, the door is made using triple glazing. This allows you to create stained glass design and enhance natural .

The following design options are popular:

• sliding models that move using a system of grooves. When installing them, it is necessary to maintain tightness. Installation is also carried out on;

• with one and two doors, which are equipped with hinged locking fittings. This requires adjustment of the hinges;

• double structures with impost. In this model, the sashes open, but an insert is placed between them - an impost;
• The shtulpovy version consists of two parts. In this case, one is fixed in one place.

Fittings are of great importance. It allows you to make the pressure tighter. The fittings are divided into internal and external. The internal elements are no different from . Internal includes door rotary knobs, balcony latches, decorative overlays and stationary handles.

Helpful information! Most important stage– this is the installation of the door frame. It is installed with precise determination of vertical and horizontal directions. Then the structure is fixed using self-tapping screws and anchor bolts.

How to adjust a plastic balcony door: methods

Most balcony owners are concerned about the question: how to adjust the plastic balcony door. You can configure the device yourself, which allows you to:

• use regulators to remove sagging canvases;
• remove shifts in any direction;
• adjust the pressure;
• place a plate under the handle for the ventilation regulator;
• Lubricate all moving parts.

A special oil composition is used as a lubricant, and you will also need a brush or cotton swab.

The table shows some door customization techniques:

Image	Adjustment methods
	Adjusting loops.
	Adjusting the position of the trunnions.
	Adjustment methods using a hex wrench
	Pressure adjustment.
	Features of setting up the end part of the balcony block
	Setting the pressure.
	Upper and lower hinge adjustment diagram.

Related article:

It is possible to cope with this task without contacting a specialist. We have collected everything you need to know about the features of regulation of these structures in this material.

The main problems of plastic doors

If the plastic balcony door does not close tightly, this can be easily corrected. You may encounter certain problems:

• When opened, the bottom of the panel rubs against the plastic threshold. This occurs due to subsidence of the structure, which manifests itself in summer time with frequent opening of the sash, as well as with a heavy double-glazed window;
• in the middle part of the leaf, the sash touches the frame element due to temperature fluctuations and drafts;
• the canvas does not adhere sufficiently to the frame, and cold air is drawn out from under the sealing material. This happens when there is insufficient pressure to the frame;
• If you often open and close the sash, the handle begins to wobble. At the same time, manipulations are performed so that the handle stops wobbling in the socket.

Adjustment of the pressure of the balcony plastic door is carried out with a hex key. To work, you will need a flathead and socket screwdrivers, tape measures and plastic spacers.

Before setting up the design, you should determine the type of problem. Most often, difficulties arise when opening and closing canvases, when skewing, when blowing, and when moving handles. If the leaf falls down or the door is difficult to close, then an individual part of the fittings is adjusted or all mechanisms are completely adjusted.

A piece of paper is used to find out if it needs repairs. It is placed on the frame and the door is closed. In those places where the sheet can be pulled out without problems, the canvas is not pressed tightly to the box. To identify distortions, the canvas should be circled in the closed state, and then the sash is opened and the lines are checked with the frame.

How to properly adjust plastic balcony doors yourself: video

It’s easy to adjust plastic balcony doors yourself; special instructions will help you with this.

Handle adjustment features

The following problems often occur:

• the handle does not turn completely or is tight. If the setting does not help, then it needs to be replaced;
• if the handle is loose, then the cover at the base of the handle is rotated 90 degrees and the two screws that are hidden behind it are tightened. A Phillips screwdriver is used for this.

Replacing the seal

If there is a misalignment in the door, it often becomes deformed. In this case, it is with the same section configuration. Old material removed from the groove using a screwdriver. Then the surface of the groove is cleaned of glue particles and dirt. When installing a new seal, you need to make sure that it is tightened. Before laying, the groove is coated with glue. This must be done in the areas where the ends of the seal will be placed.

Helpful information! For quality work door, it can be equipped with an opening limiter and a microlift that prevents sagging. The limiter does not allow the hinges to become loose.

What to do when sagging?

Many people are interested in knowing how to adjust plastic balcony doors when they settle. To carry out repairs, lift the blade higher and move it to the loop at the top. Then a certain sequence of actions is performed:

• the sash opens in a reversible position;
• Using a hex key, turn the screw next to the hinge. Then several turns are made to the right;
• to get to the screw element, you need to remove the decorative caps;
• the screw is turned clockwise and door design rises;
• freedom of movement is checked.

Helpful information! Fitting systems can fit not only hex keys, but also star keys.

Adjustment when touching the middle part

If the plastic balcony door does not close well, then make an adjustment, which can be seen in the video. When clinging to a section of the canvas in the middle, the sash moves closer to the hinges:

• the sash is retracted to the lower hinge, and then the key is inserted into the side screw and the leaf is pulled towards the direction of the hinge;
• then the same manipulations are carried out for the top loop.

How to adjust the pressure?

Similar work is carried out using locking products in the form of eccentrics. They need to be moved with pliers. To make the setup more effective, you need to study the instructions provided by the manufacturer.

Adjustments are made several times a year. In the summer, the pressure should be weaker and more dense. At the same time, you need to know how to adjust plastic balcony doors for the winter.

The adjustment is as follows:

• the decorative cap is removed;
• at the bottom of the canopy there is a screw with which the clamping force is changed;
• to change the clamp in the upper part, you need to adjust the screw itself;
• the sash swings open and the blocker is held;
• the hexagon is installed in the eccentric and rotated in the desired direction;
• the blocker is then pressed against the seal and the sash is placed in place;
• eccentrics are installed at the place where maximum pressure is applied. In this case, the fastening bolt is loosened slightly and then moved to the desired position.

Helpful advice! For better work design, it is recommended to use machine oil to lubricate the fittings.

Features of adjustment with conventional fittings

It’s very easy to decide how to set up a plastic balcony door if the fittings are standard.

To adjust the door you need:

• take off decorative details from awnings;
• using a hex key, unscrew the screw on the reverse side;
• then the long horizontal screw is manipulated. For example, to prevent the sash from clinging to the top of the frame, you need to lower the top screws and lower the leaf;
• To check the design, several turns are made.

Article