Doors made to order for non-standard openings. Doors of non-standard shape Installing a door in a non-standard opening

If you do not want to overpay 20-50 percent for non-standard interior doors, then you need to decide on the doorway in advance.

You need to start from the doors you like, the variety of which can satisfy even the most fastidious taste. Basically, doors are produced in standard sizes: 2 meters high and 60, 70, and 80 cm wide.

Helpful information:

Less common is a standard with a width of 40, 55 and 90 cm and a height of 1.9 meters. The thickness of the door frames can vary in the range of 1.5-4 cm.

Table of standard opening sizes

Depending on the room, it may be used standard size doors.

This is how they usually put it:

• in the bathroom and toilet, the height of the opening is usually from 1.9 to 2 meters, width 55-60 cm, depth 5-7 cm.
• in the kitchen height 2 meters, width 70 cm, depth 7 cm.
• in the bedroom or living room, the height of the doorway will be 2 meters, width 80 cm and depth from 7 cm to 20 cm.
• if the door to the bedroom has double doors, then only the width will change: it will be either 2*60 cm, or 40+80 cm.

After plastering and leveling the walls, the depth of the doorway will increase accordingly.

Data dimensions doorways very difficult to overestimate. After all, if you did not take them into account in your calculations, you may encounter a problem when your door frame does not fit into the opening. And not every opening can be enlarged; sometimes this is impossible due to the specific layout or design of the wall. If this bearing wall, then you will also face a number of difficulties.

Even a simple wall from plasterboard it is not easy to reduce due to transfer metal profiles. IN in this case you will have to overpay for non-standard sizes of interior doors.

There is also the opposite situation, when the doorway is much more doors. Here you will also overpay specialists when installing the door, for narrowing the opening.

An unpleasant situation may arise when, as a result of reduction, the platband cannot close the hole in doorway. In this case, you will need to seal up the uncovered sections of the wall, glue wallpaper or lay tiles. It’s good if the room hasn’t been glued up yet, but if it has been, then everything will have to be re-glued.

Therefore, even at the project stage, you need to decide on the size of the doorways, then you won’t have to overpay for non-standard doors or redo the opening.

What you need to know to calculate a doorway:

• height and width of the proposed door
• door frame thickness
• box width
• width of platbands
• the box will be with or without a threshold.

Suppose you need a door measuring 2 by 0.8 meters and 2.5 cm thick. To calculate the dimensions of the doorway, you need to add the dimensions of the frame to the dimensions of the door, plus an installation gap of 1 to 2 cm on each side.

Figure y shows a diagram of a doorway with a door and dimensions. Using these data, we can easily obtain the opening width of 800+30+30+10+10+4+2=886 mm or 88.6 cm.

You can find out the width of the frame on the website of the manufacturer of the doors you like.

• with a threshold of 2000+30+30+10+5+3=2078 mm. or 2 meters and 7.8 cm..
• without threshold 2000+30+10+5+3=2048 mm. or 2 meters and 4.8 cm..

Please note that the most common thickness is 7.5 cm and therefore many manufacturers adhere to this particular size.

If the wall is thicker or thinner than the box, then you will need to install an extension or cut the box lengthwise, respectively. Without these operations you will not be able to and everything will look much worse.

Installation interior doors- this is not a very difficult, but responsible job that requires a very careful approach. Usually people trust its specialists, but what to do if finances do not allow you to use this service? Our article will come to your aid, which will tell you how to install non-standard interior doors with your own hands. But first, let’s figure out what types of interior doors there are.

Types of doors for interior spaces

Depending on the design characteristics interior door can be:

• swing, which has one or two doors. It is customary to install a door with one leaf in standard openings, but for a non-standard opening it makes more sense to take door leaves with two leaves;
• folding, which is used to save space in the room. Depending on the design, they may have different size and represent an accordion or a book;
• door-coupe, which looks like a structure of one or two doors that move along the wall along special guides. Installing such doors will cost more if you order this service from specialists, and the cost of the doors themselves is quite high;
• the following category belongs to the group exclusive designs. These can be models made of one glass, stable models or structures that open in different directions.

Opening measurements

Below we describe the requirements that apply when the door leaf is installed for the first time and not changed.

The first thing you need to pay attention to is the walls. Work on installing the door structure should begin only after all construction activities have been completed. If the walls are not dry yet, then installed door may become warped during operation. The height of the threshold depends on the thickness of the floor covering and its type.

Before choosing interior design it is necessary to take measurements of the doorway, and if its size is standard, then it will not cause much difficulty. How does the installation of interior doors take place if they do not have standard size? You can order such a door in workshops, but you need to be prepared that its price can be quite high. The work of installing such models is not much different from standard designs, but still has its own nuances.

The frame and door leaf should not fit tightly to each other; ideally, this distance should be 2 mm on the top side and 4 mm on the bottom side. If such gaps are missing, you will not be able to open or close the door. But you shouldn’t make them big either, otherwise the door will wobble and close poorly.

The next step is to install double interior doors. At this stage you have to choose its design and what it will be.

Both models have their advantages:

• doorsliding suitable for small rooms, therefore, in order to save space, this is optimal solution. To install such doors, fastenings of a special design are required, along which the sliding of the panels will take place;
• swing design more popular. Its installation can solve the problem of sound insulation, which a sliding model will never do. But the opening system will take up more usable space, so installation of such models is recommended in spacious rooms.

Having decided on the design of the door, it is necessary to take measurements of the opening and, if necessary, adjust the size required for such a model, reducing or increasing it. The work is not difficult, but you need to remember that the width of the opening should be approximately 90-110 mm larger than the width of the canvas.

The required size and width of the opening is determined by the following formula:

Shpr = 2*(Tdk+3+Shdp)+4. Where

• Shpr is the width of the opening;
• Tdk is the thickness of the timber;
• Wdp is the width of the canvas.

If you plan to install a sliding model, then the opening needs to be prepared so that its width is smaller door leaf by 100 mm.

Materials and tools

The next thing to do is to prepare the necessary set of tools and accessories for the work:

• chisels;
• hammer;
• screwdrivers;
• roulette;
• hacksaw;
• level;
• circular and miter saw;
• screwdriver;
• perforator;
• electric milling machine

From the accessories you will need:

• door hinges;
• lock with latches.

Dismantling old structures

The next step involves dismantling old door. To install interior models correctly, the size of which does not meet certain standards, it is necessary to remove the old ones. Dismantling work begins with the removal of old structures. The old box is also dismantled.

To remove the door, you need to carry out the following manipulations with it:

• open the door 90 degrees and pull the door leaf up.
• If the door is very old, then it will not be possible to quickly remove the panel. You must first swing it in different directions, gradually lifting it up until the canvas begins to be removed.

Once you have removed the door panel, you can proceed to the next step. Next up is the box. To dismantle it, you need to remove the solution holding it to the opening, and then break out its components using a pry bar or other tool.

At this stage, the box is prepared for installation in the doorway. The work of assembling it will not cause any difficulties; the main thing here is to fit the timber to required size.

To prevent this work from leading to a dead end, experts recommend using a formula that will help you find out the required size of the timber:

Швк= 2*(Шд+3)+4. Where

• Shvk is the width of the inside of the box;
• Shd is the width of the door.

Without width and height indicator, this work installation of the door will not be possible.

Remember that the operation of the door depends on compliance with all the rules. The work of assembling the box is carried out according to the following principle:

• apply the required length of the piece to the timber and cut it along the marked lines;
• the box is designed to hold door designs, so the next thing to do is to cut the hinges into the beams;
• All that remains is to connect all the parts and fasten them.

Installing a door frame

Installation of the box takes place in several stages:

• The box is installed using a building level to avoid distortions. It is also recommended to prepare wedges so that the box does not move during fastening;
• in addition, make sure that the beams are vertical so that the frame does not extend beyond the doorway;
• after it is installed and adjusted horizontally and vertically, it must be fixed using wedges;
• holes are drilled in the box for future screws and marks are made on the wall;
• remove the box and prepare holes in the wall according to the marks;
• plugs are installed in these holes and the box is put in place, after which it is fastened with self-tapping screws;
• The cracks are filled with foam.

As you can see, the work of installing a door frame is not difficult, the main thing is to follow the necessary algorithm of actions.

Installing non-standard doors involves opening and closing doors in different directions. Therefore, before inserting hinges, you need to decide on this point and choose which way your doors will open.

Once you decide on this issue, you can start inserting the loops. Work begins with preparing holes on the side of the door, bottom and top. The main parameter when marking holes is the height. Ideally, the height of the bottom hole from the floor line should be 20-25 cm, and the height from the top edge of the door should be 15-20 cm.

If your door is a standard size, then two hinges will be enough for fastening. If the door size is large and the weight is massive, then it is better to add another attachment point, then the hangers will support even the largest and most massive structure.

After applying the markings, check them again for correctness so that you don’t have to redo the work. In addition, the height at which the hinges are located must correspond to the height of the hinges marked on the box. Now you can fasten the hinges with self-tapping screws.

Door hanging and trim installation

After installing the hinges, they begin to hang the doors. As soon as you hang it, you can start installing the trim.

Their installation can be done in two ways:

• with corners cut at 45 degrees;
• with 90 degree corners.

The work of installing platbands looks like this:

• When the door leaf is installed, it is necessary to close the junction of the frame and the wall. Platbands are used for these purposes. The work of installing them is not very difficult. The required size of the frames can be found out by measuring the tray from the floor to the intersection of the top beam of the box. This will be the height of the casing;
• The resulting height is marked on the trim strip and the required size is cut off. If the platbands are installed at an angle of 45 degrees, then another 3 mm must be added to the resulting segment. If you install platbands at an angle of 90 degrees, then the height of the segment increases by the width of the installed platbands;
• as soon as the required size of the platband has been measured, it is necessary to trim it;
• It is recommended to install awnings from the side of the awnings, thereby decorating the door leaf;
• The remaining parts of the canopies are prepared according to the same principle: I mark them and cut them off. Please note that the height parameter may not correspond to two canopy slats; it is better to take measurements for each platband separately.

Installing such a door uses a different operating algorithm:

• rollers are installed on the door leaf;

• the height at which the guide profile will be installed is measured;
• at this level it is necessary to fix the block and the guide profile on it;
• install the door into the guide profile;
• after such a door has been installed, the guide profile must be covered with a decorative strip.

In contact with

Comments

Unfortunately, there are no comments or reviews yet, but you can leave your...

New articles

New comments

Grade

Grade

Grade

We provide a unique opportunity - any size of the door leaf in increments of 1 cm. This guarantees confidence that the doors of our factory will fit any doorway. The only limitation is the maximum possible dimensions of the canvases: 240x100cm.

Keep in mind that when changing sizes, the proportions of the panels and pillar elements may change. For example, if the height of the Gloria model increases, the internal grille will remain the same size, but with a width of 60 cm, the Vienna model can only have one row of small panels.

But even in this case, there is a way out - you can supplement the height of the opening with a transom in the same style as the door model. With a wide doorway you can install swing door of two halves. But even in this case there is a way out - you can supplement the height of the opening with a transom in the same style as the door model. If the doorway is wide, you can install a swing door made of two halves.
We approach each order individually. Our managers will definitely advise and advise the best option in one or another non-standard case.

Interior doors of non-standard size from the Onyx company

The company has been operating on the market since 1997. We use only proven materials and produce products using modern equipment from Germany. At the end of the day, all products meet international requirements.

Working with the Onyx company, the customer receives:

• reliable products;
• convenient production times;
• durable material;
• acceptable prices.

Onyx products are distinguished by their level of noise insulation and durability. The doors are being moved mechanical damage and are durable. We have an individual approach to each client.

Order non-standard interior doors in St. Petersburg and Moscow

Most manufacturers of entrance doors make them in accordance with the most common openings of modern apartment buildings The exception most often is country houses, where customers prepare individual openings in accordance with their architecture.

It happens that the size of the doorway does not meet the standards followed by the manufacturer. In such cases, find suitable option in the store it becomes impossible. Then the owner starts looking to order. What pitfalls might he encounter?

Pros and cons of custom doors

Let's start with the positives. Today you can be a picky customer and confidently order individual design, especially if we're talking about about an old-style mansion. You will find “the right” color and harmonious fittings that will fit perfectly into your interior. Don't you know that a chic door is business card at home, because it will, like a magnet, attract the admiring glances of guests.

It is easy to see that the disadvantage will be production time and price. It consists of certain costs for the manufacturer to purchase special materials and increase labor costs for an individual order.

Non-standard opening - a solvable problem

Sometimes apartment owners encounter difficulties when measuring the dimensions of the entrance. Errors occur when people start measuring from boards covered with plaster. The entrance door must be attached to a solid base.

The structural features of the house can affect performance characteristics doors. And here you will need the skill of a measurement engineer to correctly calculate the parameters. Width, opening angle, safety, installation method and weight of an entrance door of non-standard sizes, everything in our company is discussed with the client at the measurement stage.

Eat Alternative option- expand or narrow the doorway. If there is already an existing decorative finishing a professional master will definitely warn you about the consequences of this or that choice, and also recommend the most suitable materials. We can offer installation of decorative trims and slopes in combination with your chosen door finish.

Arched doors

Arched openings appeared in Ancient Greece. The Romans adopted this technology and spread it to Europe. Arches were at the entrance to temples and palaces of emperors.

The transom is made of the same material as the door, sometimes from glass, stained glass and others decorative elements. Arched doors fit well into interiors classic styles(Empire, Baroque, Rococo, Classicism). Here you can find input arched doors to order from Wippro (Austria) and OpenGallery (Israel), as well as interior Mame (Germany).

WITH non-standard openings can also be encountered indoors. In order to separate one living area of ​​a house or apartment from another, you can install light glass partition. Thanks to sliding mechanisms, in a few seconds you can delimit your living space.

In conclusion

Thus, custom door It can be either a creative idea or a forced necessity. In our company you can order non-standard entrance doors(Wippro, OpenGallery) and Mame interior doors.
Whatever the task, with our doors and professional approach to each project, you can always solve it beautifully.

Firework!
This article will be entirely devoted to residents of the private sector, or rather to solving the problem of installing standard interior doors in their non-standard openings. Moreover, we will not destroy anything, we will not even take out the old box (loot), which will significantly save us replacement costs door block and speed up the process itself.
Of course it could be dismantled old block and widen the opening, but I would advise not to do this unless you know exactly how your house was originally built.
I know from my own experience that the majority of private sector houses were built without compliance and it is difficult to predict the consequences - will the opening collapse or simply deform after dismantling the old door block and further destruction, or not. Question: “Why tempt fate?” When you can take the path of least resistance.

To work we need this:

• Grinder with cutting wheel for metal and wood.
• Drill.
• Belt sander.
• Jigsaw.
• Set of chisels.
• Wood saw.
• Gun for polyurethane foam.
• Clamps.
• Electric miter saw.
• Level.
• Fraser.
• Screwdriver.

Let's get to work.
Metering.
.flv
We measure the opening where we will install the doors.
In my case, the height dimension is from the floor to the top horizontal lintel old box(lutki) is 1810 mm.
The width from the left pillar to the right pillar is 900 mm.
This means that we need a door leaf measuring 1740x800 mm, taking into account the thickness of the block of the new MDF frame and the gaps for the polyurethane foam.
Therefore, we will reduce the door only in height, but the width remains unchanged, because it's standard.
Shortening.
How to remodel doors right size I talked in one of the first articles on my site about and in an article about
As you understand, there are several ways to reduce, so use the one that suits you best.
Let’s assume that you don’t have a grinder or a router on your farm – that’s okay. You can do without this tool.
I suggest you another way to shorten.
By the way, the simplest one.
For this we need a very ordinary wood hacksaw.
note The hacksaw teeth should be fine.
The principle of operation is this.
First, along a pre-drawn line, we cut one side of the door leaf.

Important! The saw should not go out, what is called “flying out”!

Then we turn it over and finally cut off the part of the door we need.


I think this method is suitable for anyone who can hold a hacksaw in their hands.
Of course, the main disadvantage of this method is that only hollow door panels can be cut this way.
Although hollow doors are now in demand over solid doors.
So, after trimming, the resulting voids must be filled wooden slats using PVA glue or wood glue.
More little advice.

Cleaned edge door covering from fiberboard it is better to sketch with a black marker for a better appearance.
The door is ready.
Assembling the box (loots).
We measure the required size and mode.
I cut horizontal (transverse) ones 850 mm long each. If the door is 600→650 mm wide; 700→750 mm; and 900→950 mm.
I cut the vertical posts 5 mm larger than the height of the door leaf - this will be 1745 mm.
note To ensure that each pair of blanks for the future box is absolutely identical, I always use a stop when cutting.

Even a wall can serve as a support.
Also cut decorative overlays, only in different sizes.

I cut horizontal (transverse) ones, each 805 mm long.
For vertical risers, I cut 18 mm less than the height of the risers themselves (1745 mm minus 18 mm - this will be 1727 mm).

I'm fastening door frame using 4x50 mm screws.
Mortise of lock and hinges.
To mortise the lock, I use a drill with a drill bit and a router with such a cutter.
By the way, I recommend this simple and at the same time very easy-to-use cutter to everyone!

To insert hinges, like all craftsmen, I use a regular cylindrical cutter.
Installation of a new, converted door block into an old frame (lutka).
To install, you must do the following.
✓Remove old doors.
✓Use a grinder to cut off old door hinges, hooks, latches and anything else that may subsequently interfere with installation.

If you feel sorry for the old awnings, you can try to unscrew the screws and remove them.
I'll be honest, it's not always easy to do this.
✓Cut out the protruding part of the door threshold.



✓To do this, using a grinder and a cutting wheel on wood, we make thick cuts. Can be done with a hand-held electric circular saw.
If you don't have both, then use an axe.
✓Then we remove the unnecessary things with a chisel and thereby compare the threshold with the floor level.



✓We install the new box level and fasten it using wedges and screws (4x60 mm) to the old box.
note that I cut the wedges from scraps of a new MDF box.
✓We additionally strengthen it with polyurethane foam.
Installation of additional (expansion) strips.
Since in my version the depth of the old box is 150 mm plus uneven wall, I do not cover the new standard one (100 mm) and therefore the remaining 50-65 mm, depending on the curvature of the wall, I need to cover with the help of an additional strip.
In order to install extras, I do the following operations.
✓I measure the missing millimeters of width around the perimeter.


✓First I cut to length with a miter saw.

Horizontal strips - 850 mm.
Vertical - 1770 mm.
✓I cut the required width along the line with a jigsaw.


✓I install the top and bottom first, and then the sides.
To ensure a tight connection to the box (loot), I prop it up with wedges.
✓I secure everything around the perimeter with polyurethane foam.
Platband installation.
Everything is simple here.
✓I cut at an angle of 45° using miter saw. You can use a wood saw and a miter box.
✓I nail the trim with decorative nails with small heads to the box.
note , that this can only be done after the polyurethane foam has completely dried!
✓Then I paint over the hats with a black marker so that they don’t shine.
That's all, let's admire the work done.