Crafts made with a glue gun and hot glue. Crafts from hot glue: how to implement interesting ideas and an overview of the capabilities of a glue gun DIY glue gun

Nowadays, hot melt adhesive has become quite popular. It has a lot of advantages: it is harmless, easy to use (you can even melt it with an ordinary lighter), quite reliable, resistant to moisture, heats up and cools down quickly. This hot melt adhesive is usually sold in the form of oblong sticks and has several standard diameters, colors. To work with it, you need a special hot-melt gun, which gradually melts the hot-melt adhesive rod, squeezing it out in the required portions onto the surface to be glued.

You can buy a heat gun; it is a fairly common product (and relatively inexpensive). Although you can assemble a hot glue gun with your own hands. It is not at all necessary to make a heat gun in the form of a pistol. My purchased heat gun burned out a heating element after which I decided to redo it a little. As a result, instead of a thermal gun, we got a thermal syringe. Moreover, they made it even more convenient for me to glue than it was with a pistol. Although it may not look so attractive, well, homemade is homemade.

For those who don’t know, the working temperature of hot-melt glue (ordinary sticks with a diameter of 7 and 11 mm) is 120-150°C. The most important part is the temperature glue melter. I just took this part from a broken heat gun. Metal part I first wrapped the melter with mica, after which I wound nichrome wire with a diameter of 0.2 mm around it. Wire resistance 25 Ohm. Well, from here its length will vary. This new heater is powered by an adjustable step-switch power supply. The operating voltage for the thermal syringe now ranges from 12 to 28 volts. We can say that my thermo-gun, a thermo-syringe, made by myself, is powered by 16 volts.

My homemade hot glue gun in the form of a syringe also, in addition to the metal heater itself, has another important part, this is a rubber tip (made of heat-resistant rubber), into which the hot glue rod is inserted. It should match the diameter of the glue stick itself as it prevents the melted hot glue from leaking out from the side where it enters. This rubber tip was also taken from an old heat gun. When the nichrome was wound, I wound several layers of fiberglass tape over it, which served as electrical and thermal insulation. And on the fiberglass fabric I attached a finger holder made from ordinary copper wire of the appropriate diameter.

It would not be amiss to say that when it comes to winding heaters from nichrome wire (on a soldering iron, on a heater, on a hot-melt gun, etc.), then it is worth considering the following - the lead-out ends of the nichrome should be made of a larger diameter. That is, we measured the length of the working nichrome wire, and the ends themselves, about 10 centimeters long, were made from several veins of the same nichrome, twisting them together. This is necessary so that the main part of the nichrome heats up, and these ends remain cold (have minimal heating), so that over time the power cord connected to them does not lose contact.

Since the heating of the entire thermal gun, thermal syringe is quite high, the place where you need to grasp it with your fingers must be sufficiently well insulated with fiberglass tape, applying a sufficient number of turns. Overall my hot glue gun, the thermal syringe turned out well. It is compact, convenient to work with, and heats up fairly quickly (the main heat remains inside the heater, which is ensured by thermal insulation made of fiberglass). Although at first it may seem that feeding the hot melt glue rod is not very convenient, when working it is quite convenient. So if you have a broken hot glue gun, try converting it into a working hot glue syringe.

P.S. Sometimes things and tools made with your own hands seem much more convenient and better than store-bought ones. If we compare the thermal gun that I had at the beginning with the thermal syringe that I got after the modification, I like working with the latter more!

A wide variety of materials and techniques are used to create crafts and interior decorations. Sometimes completely unexpected materials are used for this purpose, such as hot glue. Photos of crafts made from hot glue arouse genuine interest and a desire to try to create something similar with your own hands.

What is hot glue?

Hot glue has another name - thermoplastic glue. The material itself consists of polymers that, when heated, acquire adhesive properties. Typically, hot glue is used to seal joints and glue products together.

Hot melt adhesive is available at most hardware stores. It is produced in the form of solid glue sticks, which differ in color, size and composition.

There is also glue in different colors. To effectively and accurately melt and dispense glue, there are special glue guns into which rods are inserted.

Operating technique

The instructions on how to make a craft from glue are very simple - buy a glue gun, suitable rods for it and use your imagination.

The main thing when working with the material is to be extremely careful and attentive, because the molten glue heats up to a temperature of 200˚ C.

What kind of crafts can be made from hot glue at home? Hot-melt adhesive can be used to decorate vases, photo frames and other interior elements or to create independent decorations.

Candlesticks

The best place to start working with hot glue is: simple tasks, for example, from decorating a candlestick. You can create an imitation of wax drips on its surface or create a unique pattern. For this purpose, it is better to use colored glue or sprinkle it with colored glitter or glue beads on it.

For decoration, you need to choose wide, thick-walled candlesticks. This choice is due to the fact that the effect of the burning temperature of a candle can have a bad effect on the glue - the design may simply blur.

Before applying hot melt adhesive, it is necessary to thoroughly degrease the surface of the candlestick for better adhesion.

You can get beautiful ideas for crafts made from hot glue from the Internet or create your own original pattern.

Vase

You can use hot glue to create a handmade vase for sweets. Step-by-step production with a description for beginners will help you easily create such a craft.

In order to make a vase for sweets yourself, stock up on hot glue, a glass bowl that will serve as a stencil and rich cream. If you want your vase to be colored, use a glue stick with the desired color or buy spray paint of the desired shade.

Apply cream to the outer surface of the bowl - it will prevent the glue from attaching to the glass when applied. Warm up your glue gun and start applying glue to bottom part bowls. Try to distribute the glue evenly - this will help form a smooth, stable bottom of your vase.

After applying the glue, you must wait until it is completely polymerized. You can begin to separate the glue from the bowl only after it has completely hardened, otherwise the craft may be irreparably damaged. After removing the hot glue basket, you can spray paint it.

rolling pin

For those who love working with polymer or ceramic clay, the idea of ​​​​making rolling pins with patterns will be very useful. To do this, you need to take a new, clean rolling pin. the right size, degrease well and draw the required pattern on it with a pencil or marker.

Then use a glue gun to apply glue to the pattern lines and wait until it dries completely. You can also treat the rolling pin with cream or oil before applying glue - this will allow you to remove the glue after using the required pattern and apply a new one to it.

New Year decoration

For your child, you can conduct a master class on crafts using hot glue. Make a large drawing of a snowflake; you can ask the child to make a stencil. Then use carbon paper to transfer the design onto parchment paper for baking.

Apply hot glue along the contour of the drawn snowflake to make a three-dimensional copy of it. Carefully monitor your child's actions at this stage - he may get burns from the hot polymer.

Wait until the polymer has completely hardened and separate it from the paper. After the snowflakes have dried, they can be decorated with ordinary nail polish or spray painted.

Photos of hot glue crafts

Useful tips

Regular glue gun with hot glue can be used not only for gluing various parts, but also for creating various patterns and crafts.

When working with hot glue, be careful and pay special attention to the safety of children, because the glue gun heats up and the glue comes out very hot.

Here are some very interesting and extraordinary ideas on how else you can use a glue gun and hot glue:

Crafts made from glue. We use wax crayons.

You will need:

Glue gun

Wax crayons

* It is possible that after using wax crayons, your glue gun will deteriorate, so it is advisable to use an old or inexpensive gun.

*If children are working on the project, be careful when working with a hot glue gun and hot melted crayons.

1. Remove the labels (papers) from the crayons.

2. Cover your work area with an old towel.

3. Heat up the glue gun.

4. Carefully insert the chalk into the glue gun and gradually press it down. The glue gun trigger won't be able to push them through, so you'll have to do it by hand.

5. The wax will begin to melt and you will be able to use colored wax drops to create colorful blots.

Wax stamping is another way to use wax crayons and a glue gun to create vibrant images.

DIY glue crafts. Decorate a vase or candlestick with hot glue.

You will need:

Inexpensive, round vase or candlestick

Heat the glue and begin to carefully apply it to the vase, layer by layer, so that you end up with transparent lines on the walls of the vase.

If you want to make straighter lines, ask someone to help you - let them twist the vase for you while you apply the glue.

Unusual crafts. Hot glue corals.

You will need:

Thin wire

Hot glue gun

Acrylic paint

Brush

Piece of plywood

Nails and hammer.

Making red coral

1. Cut the wire into several pieces of different lengths. IN in this example their length varies from 10 to 40 cm. Bend each piece in half.

2. Heat the glue and carefully cover all the pieces of wire with it.

3. Select the color you want to paint the coral in in this case red. Use acrylic paint to paint the glue on the wires.

4. When the paint is dry, you can assemble all the parts into one coral. Take 2-3 pieces of wire with glue and connect them together using another thin, clean wire (not covered with glue).

Add 2 more parts to the structure and connect them again with clean wire.

In order for the coral to stand on a flat surface, all ends of the clean wires must be twisted and bent into the shape of a stand (see image).

Making white coral

1. Cut 3 pieces of wire, each between 30 and 35 cm long, and twist their ends together.

2. Bend all the wires the way you like and place them on a flat surface to which hot glue will not stick - glass, for example.

3. Cover all the wires with glue. After this, you can add additional branches of glue to your design.

4. Once you have the coral in the shape you want, let the glue dry and paint it white acrylic paint.

5. To make the base for the craft, prepare a piece of plywood and attach the ends of the wires to it with nails.

6. Cover the ends with glue and paint with acrylic paint.

Unusual DIY crafts. Snowflakes made from hot glue.

You will need:

Hot glue gun

Nail polish or acrylic paint

Parchment paper (NOT waxed (wax) paper)

A drawn snowflake shape (if desired).

1. Print or draw a snowflake on a regular sheet of paper and place the design under parchment paper.

2. Using a glue gun and hot glue, trace the snowflake design. Wait a minute for the glue to dry.

If necessary, after the glue has dried, you can straighten the shape a little using a hairdryer.

3. Carefully remove the snowflake from the paper. The paper can be further used to create several more snowflakes.

4. Both sides of the glue snowflake can be painted with nail polish or acrylic paint.

Original DIY crafts . Rolling pin with a pattern.

You will need:

Any rolling pin

Felt pen

1. Draw any pattern on the rolling pin. It is advisable not to draw too many lines.

2. Heat the glue and start applying it to the lines drawn on the rolling pin. It is advisable to carry out the entire process on a flat surface covered with newspaper or cardboard.

3. Once the glue is dry, you can use a rolling pin to create a design on the clay by rolling it out.

The glue can be removed and a different pattern applied.

Original crafts. Glass holder for candles.

You will need:

Small glass vase or glass

Hot glue gun

Aerosol or acrylic paint

Spray oil or simple vegetable oil.

It is advisable to choose a wide vase so that the heat from the candle inside does not heat the glue, which may leak.

1. Wash and dry the vase, then wipe it with vegetable oil and a paper napkin.

2. Start applying hot glue to the back of the bottom of the vase, drawing patterns with it. The main thing is that all the lines intertwine well so that it is easier to remove the glue from the vase.

Continue drawing patterns with glue on the sides of the vase.

It is advisable to wear glasses to protect your eyes, as the glue will heat the glass.

3. Once the glue has dried, carefully begin to separate the design from the vase. You may need to use a screwdriver, knife, or other tool to make it easier to separate the design from the glass vase.

4. Clean the vase from any remaining glue. Use dishwashing detergent.

5. Paint the glue design. If you are using spray paint, read the instructions carefully and act according to them.

Now you can insert a glass or vase into the candle holder and you will get great decoration interior

Interesting crafts for children. Multi-colored dots for various crafts.

You will need:

Hot glue gun

Acrylic paint or nail polish

Brush.

It will take a little practice to get such smooth parts, but in the end you will succeed, and all these parts can be used to make various crafts and postcards.

Each dot can be painted with acrylic paint or nail polish.

Crafts for children: do-it-yourself printing (video)

* First, cover the table surface with a special silicone board or silicone oilcloth.

Crafts for the home: making a vase from glue (video)

Interesting DIY crafts. Makeup brush cleaning board

How to make a glue gun yourself? Today we’ll look at an option that involves using .

With my real experience in this matter, on the pages of an industry publication 3D Today, shared by a portal user under a pseudonym TanyaAkinora. We present to your attention her story. The author's punctuation and spelling have been traditionally preserved.

As a maker, in my creativity I use various instruments, including glue gun. For miniature work there is a small gun with a 7 mm rod. But in any case, you have to press the trigger, making some effort. And this is not always convenient.

This is how the idea of ​​making my own instrument came about.

in this regard, an indispensable assistant. The experience of using 3D pens suggested a housing option. The result was a device that I called GlueDart

. This is a glue gun in the form of a handle with an electric one for 7 mm sticks. The feed button is located on the front side under thumb right hand . Thus, it turned out handy tool

, which makes the gluing process more accurate and precise.

All plastic parts are 3D printed. During use, the case practically does not heat up.

The extruder uses a reciprocating mechanism and a small motor with a gearbox. An attempt to make an extruder similar to a 3D printer was unsuccessful, since the glue stick is much softer than the filament rod.

Thus, it turned out convenient and lightweight tool with safe 5V power supply. A blue LED is used as an indicator of the on state.

An option with speed control was created, but this option turned out to be superfluous.

All modeling was done in Autodesk 123D Design, and some details (axial cam) and partly video in Fusion 360.

I wish all makers creative success.

We print a glue gun on a 3D printer - video

Equipment: Anet A8 3D printer

A 3D printer was used to implement this case. Anet A8. This is an updated version of the previous Chinese printer model - Anet A6.

The print area is 220x220x240 millimeters. The printer is equipped with a heated bed, a display and can print with materials such as ABS plastic, PLA, HIPS and some others.

In this way you can create many useful things and tools in everyday life. If you have your own experience in this matter, let us know and your story will appear on the pages of our section.

Noticed a mistake? Select it and press Ctrl+Enter

Every needlewoman has such a tool as hot glue. This item is required if you need to glue something together. Moreover, it can be used not only for its intended purpose, but also to create wonderful crafts. For example, you can look at photos of crafts made from glue to understand what we are talking about now.

Cat scratcher

There is no need to buy a special comb for pets, because you can make one yourself. Take ordinary rubber gloves of the color you like and apply small drops of glue over the entire area. Give time for the glue to dry properly, and you can start stroking the cat. This process will not only be pleasant, but also useful, since such a tool will remove excess hair from the animal and it will not fly all over the apartment.

Buttons

If you are going to decorate any item in your wardrobe with your own hands, then undoubtedly great solution will become a button made of sparkles.

The only tools you will need are hot glue and the glitter itself. It is necessary to pour glitter and organize a circle out of them, then the whole thing is covered with glue and a small amount of glitter is added on top. When the glue dries, you need to use a toothpick to make several holes through which the button will be sewn to the clothing.

Moreover, such crafts made from hot glue with your own hands can be sold and you can organize a good profitable business.

Eraser at the end of a pencil

Have you seen pencils on back side Which eraser is located? So, glue can become the same eraser, and it will cope with the task no worse. Just apply a little glue to the end of the pencil in a ball shape and let it dry.

Unique vase

Do you have a glass one at home? transparent vase? Try making it more original with hot glue. Just apply the glue evenly in the form of a texture or pattern over the entire area of ​​the vase, let it dry thoroughly, and you will get a non-slippery vase with an unusual design.

Shoes

Just as in the case of a vase, you can achieve an anti-slip effect for other objects. Best idea– a craft made from glue for making shoes that won’t slip on ice. To do this, apply in small areas or apply strips of hot glue to the soles of your shoes and wait for it to dry.

Now you don't have to be afraid that you will immediately fall as soon as you step on the ice. You can also use glue to make an inscription on the sole, which will look very unusual.

In the same way, you can get hangers (hangers) for clothes, from which clothes will not slide off. Apply a little glue evenly to the clothes hanger and wait until it dries completely. Try the improved item!

Interior decoration

Apply glue to wax paper so that you get some kind of shape, for example, it could be a snowflake. Wait for the glue to dry, and for an even more stunning effect, you can paint the snowflake with nail polish. different colors. Decorate a Christmas tree, wall or window with such figures and they will delight the eye.

Please note that if you work with this glue with children, be extremely careful, since the glue gun itself gets very hot, and the glue will be very hot - one awkward movement and you can get burned!

It is not necessary to look at the techniques that are used to make crafts, try to take paper and make crafts from paper and glue using your imagination, we are sure that you will find a use for all this.

Wax crayons

Crafts created with wax crayons can seriously damage your glue gun, so for this hobby it is better to take an old or unnecessary tool.

Instead of glue, you need to insert colored chalk into the hole, and when the gun heats up, carefully push it inside. Under the influence of temperature, the chalk will melt, and the molten colored mass will begin to drip from the gun. Very convenient to use for creating colored blots in a composition.

Candlestick

For this work you need a glass vase or glass, glue with a gun, acrylic or aerosol paint and spray oil or regular vegetable oil.

Choose a wide container that you will use as a candlestick, since the temperature of the burning candle can melt the glue, which will undoubtedly ruin the product.

Clean the vase from traces and cover with a thin layer of oil. Create beautiful pattern or a pattern on the outer surface of the glass, you can even come up with a special structure.

It is best to apply lines of glue that will touch each other in case it is easy to remove the adhesive layer from the glass.

The next step is to carefully separate the adhesive layer from the glass. You can use a knife or screwdriver to make it easier to remove the layer.

When the job is finished, the glass must be rinsed from traces of glue; this is best done by detergent. And the candlestick itself needs to be painted with your favorite color. If you are using spray paint, please read the instructions carefully before using it.

An interesting look are crafts made from threads and glue, which cover, for example, a vase with a layer of multi-colored threads, and the glue is used as a binder.

You don't have to look at someone else's work and copy it exactly. Use your imagination and you can come up with adhesive accompaniments for any item in your interior. There are a lot of options, you just have to raise your head and run your eyes over the objects that surround you.

You can also find on the Internet various master glue craft classes that will help you if you really can’t come up with anything on your own. Some tips can be very useful.

Try to surprise your guests and loved ones with such gizmos that are made strictly only from glue, without the use of other decorative items. Take our instructions on how to make a craft from glue as a basis, supplement them with something of your own and you will truly amaze your future fans.

Photos of crafts made from glue