Watering can for flowers from a plastic bottle. DIY garden watering can from an old plastic canister DIY garden watering can attachment
Indoor, garden and garden plants need regular watering. Ideally, the applied water during irrigation does not erode the soil, so for irrigation it is better to use a specialized watering can that divides the flow into several thin streams. Although this is an inexpensive piece of equipment, it is not necessary to buy it, but can be made for free in a couple of minutes from a canister that would have been thrown away anyway.
Materials and tools:
- canister with handle;
- drill;
- drill 2 mm.
Making a watering can from a canister
10-20 holes are made in the lid of the canister using a 2 mm drill. If you don't have a drill, you can burn them with a hot nail. To do this, he warms up over gas stove or an ordinary candle. To avoid getting burned, the nail should be held with pliers. It is better to burn the lid in the open air, as smoke and the smell of burnt plastic are released.
To prevent the canister from deforming when pouring water, and the liquid flows out quickly, air must enter the watering can to prevent a vacuum. To do this, you need to make one hole in the handle near the neck with the same drill or nail. After filling, the watering can is ready for use.
Benefits of use homemade watering can from a rigid canister with a handle over an ordinary PET soda container are undeniable. This homemade product is much more spacious, it does not shrink when pouring, thanks to the handle it fits more comfortably in the hand, and water flows out of it in even streams without jerking.
Anyone who grows seedlings knows firsthand how difficult it becomes to water seedlings when they grow. To somehow make their work easier, summer residents invent various watering cans. We invite you to familiarize yourself with some of them.
1. Insert a slightly curved tube into a clean plastic bottle (1.5-2 l). It should be longer than the height of the bottle so that you can easily water the seedlings even in the most inconvenient place.
To prevent it from decreasing in diameter (flattening) when bending the tube, cover one edge of the tube with plasticine or clay, pour in water and place in the cold (you can freezer), so that water does not spill out of it. When the water turns into ice, bend the tube. In this case, the handset itself will receive the required form, and the ice will not allow the walls of the tube to shrink.
Many gardeners grow seedlings in foil containers, and a watering can made in this way will be an excellent assistant in caring for seedlings.
2. Sometimes seedlings do not require root watering, but with the capture of leaves. To avoid accidentally dousing the seedlings with water, make a shower head with your own hands.
Wash the half-liter plastic bottle thoroughly, remove the stickers from the outside and use a marker to put dots in place of which you will later make holes. Place the dots in a 5x5 square.
Hold the head of the nail in the pliers and burn the end of the nail over a fire (candle) for 20-30 seconds. Now pierce the drawn points with a heated nail. When the nail cools down, heat it again. On back side Using a knife, cut a hole in the bottle for filling with water so that it is 2-4 cm higher than the watering holes. Fill the bottle with water and carefully place it horizontally above the plants.
For convenience, you can use tape to make a handle on a watering can.
3. There are never too many watering cans, either at the dacha or at home for seedlings and plants. Many plants cannot be watered with a hose, this rule is especially often heard in greenhouse gardening, so it is best and easiest to have a watering can at every step. In order not to spend money on the purchase, we suggest making it yourself. To do this, take any plastic canister (for water, car oil), polypropylene pipe 50 cm long and rotated 60°.
Place a “turn” near the bottom on a flat place and use a marker to mark the diameter of the future hole. Cut out and try on how easily the pipe fits into the canister ( large gap must not be). Thoroughly lubricate the joint with hot glue, insert the pipe and leave to dry. Next, all you have to do is put a piece of pipe on the pipe and, if necessary, shorten it by cutting off the excess. The optimal length of the “spout” is considered to be the height that does not exceed the lid of the canister.
Tie the tube (spout) to the handle of the canister so that it does not break under water pressure. You can insert a cut plug into the spout so that the water fan out in a limited flow. If you have to use a watering can to scoop up water in a well, then for ease of filling with water, make a hole on the opposite side of the spout so that the air can quickly escape.
4. You can also make an excellent watering can from a small plastic container (shampoo bottle). To do this, just make holes at the bottom with an awl or nail. Fill a container with water, close the neck, turn it upside down and water.
5. You can make the most primitive watering can. Make holes in the lid of the plastic canister and on the opposite side for air to escape.
6. If it is not possible to regularly water seedlings or seedlings, then it makes sense to use automatic watering. For this at the bottom plastic bottle Make holes with a hot nail, fill the container with water and close the lid. Plant bottles in the ground near each plant in the garden or one for several seedlings.
As you can see, there are many options for making a watering can with your own hands, choose yours, make it and share your suggestions.
Today I will make a watering can from a plastic bottle. Since it can be difficult to reach with a regular watering can to water flowers, and some flowers require careful watering, I came up with a watering can for myself. Below I will tell you how to do it.
We will need: a plastic bottle of any capacity, a plastic tube longer than the length of the bottle (we used tubes on which to put balloon), knife and glue gun.
We make a hole in the plug slightly smaller than the diameter of the tube. I did it with a sharp knife.
We insert the tube.
It should reach the bottom of the bottle, but not rest against it.
We make a mark where we will cut it.
The good thing about a glue gun is that it produces a thick, quick-drying layer of glue.
We insert two tubes into the holes made and glue/seal them to the lid.
When the glue has cooled, fill the bottle with water and use it by pushing the watering can between the leaves, down to the ground. When watering from such a watering can, the stream will be constant and not strong, and most importantly, there will be no “gurgle-gurgle.”
It may not look aesthetically pleasing, but it is fast and practical :)
Another tip. If you accidentally overwatered a flower and the water started running over the edge flower pallet, then you can close the short tube with your finger, squeeze the bottle, and lower the long tube into the water, then let the bottle restore its shape, and it will begin to draw water into the bottle like a pump.
Where else can this watering can come in handy:
Pour water into the iron reservoir.
Water carefully and in measured doses houseplants and seedlings.
Anyone who grows seedlings knows firsthand how difficult it becomes to water seedlings when they grow.
To somehow make their work easier, summer residents invent various watering cans.
And it’s not at all necessary to go to the store and buy a watering can, especially if you don’t use it often.
You can make a tool for watering plants with your own hands from available materials.
We invite you to familiarize yourself with some of them.
Ways to create a watering can for the garden
Option 1
- Insert a slightly curved tube into a clean plastic bottle (1.5-2 l). It should be longer than the height of the bottle so that you can easily water the seedlings even in the most inconvenient place.
- To prevent it from decreasing in diameter (flattening) when bending the tube, cover one edge of the tube with plasticine or clay, add water and place it in the cold (maybe in the freezer), so that water does not spill out of it.
- When the water turns into ice, bend the tube. In this case, the tube itself will take the desired shape, and the ice will not allow the walls of the tube to shrink.
Many gardeners grow seedlings and a watering can made in this way will be an excellent assistant in caring for seedlings.
Option 2
Sometimes seedlings do not require root watering, but with the capture of leaves. To avoid accidentally dousing the seedlings with water, make a shower head with your own hands.
- Wash the half-liter plastic bottle thoroughly, remove the stickers from the outside and use a marker to put dots in place of which you will later make holes.
- Place the dots in a 5x5 square.
- Hold the head of the nail in the pliers and burn the end of the nail over a fire (candle) for 20-30 seconds.
- Now pierce the drawn points with a heated nail. When the nail cools down, heat it again.
- On the back of the bottle, use a knife to cut a hole for filling with water so that it is 2-4 cm higher than the watering holes.
- Fill the bottle with water and carefully position it horizontally over the plants.
- For convenience, you can use tape to make a handle on a watering can.
Option 3
There are never too many watering cans either at the dacha or at home for seedlings and plants. Many plants cannot be watered with a hose, this rule is especially often heard in greenhouse gardening, so it is best and easiest to have a watering can at every step.
In order not to spend money on the purchase, we suggest making it yourself:
- To do this, take any plastic canister (water, car oil), a polypropylene pipe 50 cm long and turn 60°.
- Place a “turn” near the bottom on a flat place and use a marker to mark the diameter of the future hole.
- Cut out and try on how easily the pipe fits into the canister (there should not be a large gap).
- Thoroughly lubricate the joint with hot glue, insert the pipe and leave to dry.
- Next, all you have to do is put a piece of pipe on the pipe and, if necessary, shorten it by cutting off the excess. The optimal length of the “spout” is considered to be the height that does not exceed the lid of the canister.
- Tie the tube (spout) to the handle of the canister so that it does not break under water pressure.
- You can insert a cut plug into the spout so that the water fan out in a limited flow.
If you have to use a watering can to scoop up water in a well, then for ease of filling with water, make a hole on the opposite side of the spout so that the air can quickly escape.
Option 4
You can also make an excellent watering can from a small plastic container (shampoo bottle). To do this, just make holes at the bottom with an awl or nail. Fill a container with water, close the neck, turn it upside down and water.
Option 5
You can make the most primitive watering can. Make holes in the lid of the plastic canister and on the opposite side for air to escape.
Option 6
If it is not possible to regularly water seedlings or seedlings, then it makes sense to use automatic watering. To do this, make holes in the bottom of a plastic bottle with a hot nail, fill the container with water and close the lid. Plant bottles in the ground near each plant in the garden or one for several seedlings.
As you can see, there are many options for making a watering can with your own hands, choose yours, make it and share your suggestions.
Hello DIYers, as well as summer residents and gardeners! This August has finally taken revenge on the previous two abnormally cold and rainy summer months. He has already managed to pamper us with real summer warmth and even heat, but the situation with rain was the opposite, since there was practically no rain this August. Therefore, we had to again take up the watering cans and watering cans and water the garden beds. And then, in the midst of watering work, our purchased watering can nozzle for a plastic watering basin completely broke down. I must say that from the very beginning it was quite flimsy, and even earlier it had to be wrapped with electrical tape. But then a whole piece broke off and it became completely unsuitable for watering.
We actually also have two old metal showers with durable metal nozzles, however, they are quite heavy and not very easy to use. Moreover, it is especially difficult for women to use them. From this point of view, a modern plastic shower is, of course, much more convenient and therefore is used most often. Therefore, I decided to quickly make homemade nozzle for this watering, literally from what was at hand.
The materials I needed for this were:- An empty plastic shampoo bottle;- A piece of old rubber hose. Tools needed:- Cordless drill-driver;
- Metal drill with a diameter of 2.5 mm;
- Knife;
- Shilo.
Making a waterfall
First I cut a small piece of rubber hose.
This hose fits very well into the neck of the shampoo bottle, since it fits onto it very tightly and firmly and no additional fastening is required.
However, in order to attach the other end of this piece of hose to the spout of the waterer, you need to remove a certain layer of rubber from the inside using a knife.
And this piece of hose fits quite easily, but at the same time very tightly, onto the spout of the waterer.
Now you need to modify the shampoo bottle by drilling holes in it.
To do this, you first need to mark and prick the centers of future holes with an awl.
And then drill them out with a drill.
After this, all that remains is to cut off with a knife from the surface of the bottle the pieces of plastic remaining after drilling the holes.
Then you need to rinse this bottle from any remaining plastic shavings that have gotten inside, and put on the previously prepared piece of rubber hose. And now our nozzle is ready!
Now you can put it on the spout of the waterer.