How to renovate a bathroom inexpensively. Do-it-yourself bathroom renovation - the simplest options for carrying out work, available to everyone. Economy option for bathroom renovation

A bathroom can be renovated exquisitely, even using the simplest Construction Materials. It is not necessary to purchase elite porcelain tiles and lay them on the walls right up to the ceiling, order stretch ceiling, to spend money on installing heated floors with marble, it is enough to have a desire to do repairs, the ability to handle tools and a little bit of good taste.

Under the word “budget”, the article will consider finishing options with the most affordable materials:

• paint and varnish;
• PVC panels;
• wallpaper.

In addition, the secret of creating an interior in style will be revealed and it will be proven that brick as a finishing material in the bathroom is not inferior to other materials. After all " budget renovation"can also be stylish.

DIY wall painting

Painting walls is considered one of the easiest and least expensive finishing methods. It is important to choose the right paint and prepare the surface of the walls.

Advice! Create a design project for your bathroom. It is not recommended to paint absolutely all surfaces; it is advisable to cover the areas around the bathtub and sink with moisture-resistant panels or trim them with an apron made of inexpensive ceramic tiles.

Step 1. Choosing paint for the bathroom

Bathroom paint should have antibacterial properties and be moisture resistant. Otherwise, the appearance of fungus and peeling of the coating cannot be avoided.

Traditional oil paints are deprived of such dignity, and also quickly become covered with cracks, so it is better to abandon this option immediately.

When choosing shades, remember that bathrooms small area It is inappropriate to paint in dark colors, as visually this will further reduce the space. Do not overdo it with the number of bright spots or complex patterns and their quantity so that the interior does not look vulgar. Soft pastel colors will visually expand the room and fill it with light.

Please note that paints can be matte, glossy or semi-gloss. Of this variety, it is matte enamels that best hide small defects on the walls, while drops and streaks are clearly visible on glossy surfaces. However, if you cannot make a choice, consider a combination of glossy and matte surfaces. This technique will make your bathroom modern and stylish without significant costs.

bathroom paint

Step 2. Preparing the walls for painting

Don’t forget to remove all the furniture from the bathroom, remove the mirrors, cover the faucets with masking tape, and cover the plumbing fixtures with film or newspaper, because preparing the walls for painting is the dirtiest and most time-consuming stage.

You should not apply new layers of paint over the old peeling one, nothing good will come of it. If you have a drill in your arsenal, buy a pair for it grinding attachments and remove old paint from walls. Remember safety precautions.

Paint can be removed using thermal methods, for example, using a torch or construction hair dryer. Heat a section of the wall and scrape off the peeling coating with a narrow spatula.

When all the old paint has been removed from the walls, it is necessary to repair cracks and potholes and knock down protrusions.

Step 3. Preparing materials and tools

Prepare paint and tools, follow manufacturer's instructions. To apply paint you will need a roller, brushes, if you have a spray gun - great. Before purchasing, measure the area of ​​the surfaces to be coated and adjust the amount of material taking into account the volume. For high-quality painting, it is better to apply two layers, keep this in mind when purchasing.

Step 4. Preparing the workplace

Free yourself from unnecessary items workplace near the walls, if you are not going to redo the floor coverings, then cover them with film or paper. Carefully protect the bathtub and sink from contamination.

Start your work from the most inconspicuous corner, in this place you can learn the properties of the paint in practice and, if necessary, dilute it to the optimal consistency. We recommend painting the walls with a roller, and using a brush to treat only hard-to-reach areas, corners and borders of joints of different colors. Panels in the bathroom are still in fashion; if you plan to make them, mark the height on the wall and draw a horizontal line.

Step 5. Start coloring

Apply primer deep penetration on the wall. It will not only improve appearance, but will also increase the strength of the coating and reduce the likelihood of paint peeling.

Apply a second coat of primer over the first and wait 24 hours

Pour a portion of paint into a special plastic tray for rollers. Dip the roller into it, turn it several times, remove excess paint on a horizontal surface.

Practical advice. To minimize the chance of paint getting on the floor, give the roller a spinning motion before blowing it out of the tray.

Step 6. Painting technology

Start painting from top to bottom, this method reduces the likelihood of drips forming, they are immediately smeared, and the roller “rolls” over them. Paint carefully, do not allow any omissions. Don't be upset if the first coat looks ugly, this is expected. The fact is that there are areas on the wall with old and new plaster, remnants of un-removed coating, etc. They all absorb paint differently, which is reflected in the appearance. The second coat will correct all problems, the finish will be uniform.

Paint in small areas, difficult places straighten it with a brush. The paint should smooth out lint marks on its own. If this does not happen, add solvent to it. Pay attention, so that he is conscientious, read the instructions for use. If in doubt, test the solvent for compatibility with a small volume of material; if the paint has curled, change the solvent.

It is advisable to apply the second layer when the first one is not completely dry, this increases the adhesion coefficient between them. It’s easy to check the readiness of the surface - run your fingertips along it, they should not get dirty, but only “creak” a little.

If you are making a multi-colored panel, then you need to paint the surface in the second color only after applying two layers of the first. In this case, start working from the top of the wall; the panel is finished last. This way you will be protected from paint getting on already ready plots. Apply masking tape along the border line. Make sure that the paint does not flow under it; paint only with a brush, moving in the direction opposite to the tape. Never apply tape to paint that is not completely dry, this is very important. If you glue it to a freshly painted surface, then during removal it is likely that part of the paint will be removed along with it, and you will have to redo everything.

Wall decoration with PVC panels

The cost is slightly more expensive than the first method, but in terms of design indicators it is much better. Yes and preparatory work are significantly lighter, there is no need to remove old coatings, level the walls and seal cracks in them. The sheathing for the panels can be made from wooden slats or special plastic profiles with clips. We recommend using the second option. The cost of plastic additional elements has almost no effect on the cost of repairs, and the work is greatly simplified. In addition, the plastic profile is not afraid of moisture, which is very important for bathrooms. Wood slats need to be soaked with antiseptics - an additional waste of time.

Calculate the number of panels needed, make a reserve of 5–10%. If you have little experience, but the bathroom has a lot engineering communications, to close which you will need to trim the panels, then take a reserve of 10%. At the same time, estimate the number of starting profiles, external and inner corners. They are sold at a standard price, cost a penny, and there is no need to save money.

Step 1. Installation of the sheathing

The panels are arranged vertically, the sheathing must be made horizontal. The distance between the planks is 50–60 cm. Make markings on the wall, making sure that the lines are parallel. The sheathing is fixed with dowels, drill holes with a drill and hammer drill, use drills with Pobedit soldering. To prevent the floor from getting dirty with construction dust, cover the area near the wall with film or paper. Once all the holes are made, remove it immediately. Don’t leave cleaning for later; practice shows that no matter how carefully you work, garbage will definitely spread throughout the bathroom.

Make the holes a few centimeters deeper than the length of the plastic part of the dowels, otherwise you will not be able to insert them all the way, dust will interfere. First, drill the two outer holes, attach the profile, then fix it in several more places. The horizontal distance between the dowels is 60–70 cm.

How to fix elements in one plane?

1. Check the condition of the wall with a plumb line, pay special attention to the places where plastic profiles or slats are attached.
2. Fix the two outer elements below the level and re-check their position. If there are large recesses where the profiles are attached, then use pads made of various materials. The dowels must attract the profile along the entire plane; there cannot be a gap between it and the wall at the attachment point.
3. Stretch ropes between them, two at the ends of the profiles or slats are enough.
4. Install all other profiles under the rope; use it to control the position of the slats.

Step 2. Installation of plastic panels

Take measurements of the wall in at least three places. If they have a spread of no more than a centimeter, then the work is noticeably simplified - all panels can be cut to size at the same time. To do this, you need to find out the shortest one and use it to cut all the others. Stack the panels in stacks of 5–10 pieces. on a flat plane and use a grinder with a metal disc to cut it. A discrepancy of up to one centimeter will be hidden by the ceiling and floor profile. It is installed at the top between the wall and the stream and at the bottom at the junction of the wall and the floor. Place plastic corners on the sides.

Remove exact dimensions last panel, cut it lengthwise. You can cut with a mounting knife or grinder. If you use a knife, the operation must be done in two stages. First - cut top part and transverse stiffeners. Second - bend the panel, at the bend on the second side, use a mounting knife to completely cut off the required part.

Finish the remaining walls in the same way. Practice shows that it is better to make the area near the bathtub from ceramic tiles. You don’t have to cover the entire wall, just an apron. The main thing is to close the area that constantly gets water during water procedures.

Video - Installation of PVC plastic panels in the bathroom

Video - Finishing bathroom walls in 1 day with plastic panels. Inexpensive DIY bathroom renovation

Wallpapering walls

For wallpapering, you can use only waterproof types. This finishing method has a number of undeniable advantages.

1. Low cost allows you to have exclusive and reliable coverage with small material losses.
2. High technology. Among all possible ways decorating the walls in the bathroom, wallpapering is the simplest. The work is completed within a few hours, the room can be used for its intended purpose the very next day.
3. It is possible to frequently change the design of the premises. In some cases, re-pasting can be done without removing the old one - the repair time is significantly reduced and the amount of construction waste is minimized.

Disadvantage: wallpaper is inferior in terms of physical strength traditional materials. But, if you behave carefully and avoid mechanical damage, the period can be calculated in many years. In addition, defects on wallpaper can be easily eliminated; after pasting there will always be a small amount of material left. Don't throw it away, keep it “just in case” for repairs.

Which wallpaper to choose for a bathroom

It goes without saying that only waterproof ones. When purchasing, pay attention to physical strength, and it depends on the material of manufacture.

How to glue wallpaper correctly so that you don’t have to constantly re-glue the peeling areas?

Step 1. Surface preparation

Most important point production of work, of course, not counting the correct choice of wallpaper. The linearity parameters of the wall affect not only the appearance of the wall, which is very important, of course. On uneven wall It is even theoretically impossible to glue waterproof wallpaper. This means that there will definitely be air pockets and other places where the wallpaper is not glued. While using the bathroom, these areas constantly increase in size, and this continues until the peeling becomes noticeable. Repair will be required; perfectly aligning the wallpaper after repair is quite difficult, and in some cases impossible. What are the requirements for the wall surface?

Surfaces must be primed in two layers, this increases the reliability of adhesion and serves as additional protection against moisture penetration.

Calculate the surface area, make a small reserve. Each roll of wallpaper indicates the length, width and total area. Use this information when purchasing materials. Do the same when choosing glue.

Step 2. Algorithm for gluing vinyl wallpaper

Measure the height and width of the wall, cut the required number of strips. The stripes, depending on the pattern, can be applied end-to-end or overlapping. Cut with a small margin in length, it will then be removed with a knife, the uneven cut will be buried in the ceiling and floor skirting boards.

Practical advice. It is most difficult to glue wallpaper in the corners of the room. The fact is that they can have slopes, and this has Negative influence for quality. To prevent such consequences, never make strip joints at the corners; try to have them in the middle in these places.

1. Glue the strip coated with glue to one wall of the corner, align it strictly vertically.
2. Carefully bend the wallpaper, but not all the way into the corner, lightly glue the strip to the second wall.
3. Slowly begin to bend the wallpaper towards the corner, while constantly monitoring the displacement of the second edge, it should always be in a vertical position. An uneven wall angle is not a problem; even if there are air pockets in some places, the main thing is that the edge of the wallpaper on the second wall is vertical.

If you do not pay attention to this nuance, then on the entire adjacent wall the stripes of wallpaper will be slanted, and this is a big waste.

To apply glue you will need large room, the bathroom, as a rule, does not have such dimensions. Decide where exactly you will prepare the wallpaper. Take measures to prevent contamination of floor coverings, do not allow glue to get on the front surface. When wallpapering walls, neatness is one of the important conditions quality work.

Carefully squeeze out the air from under the wallpaper. You can use rubber spatulas or rollers. But it is best to do the work with clean, dry hands. This way you will feel the irregularities and be able to eliminate them in a timely manner. It happens that an air pocket is discovered late, several strips of wallpaper have already been pasted. It's not a problem. Poke the air bubble in 2-3 places with a needle, after which you can press the wallpaper again, it will take the desired position.

Without pressing, cover the switch with wallpaper and make a diagonal cut through it. Carefully cut out the edges and press the wallpaper to the wall

Once the glue has completely dried, cut off the excess length and attach the baseboards. Skirting boards are attached liquid nails or in other ways, taking into account the material of their manufacture.

How to renovate a bathroom in loft style

The style is quite fashionable among young people, but it is difficult for older people to get used to it. The loft style is a method of renovating various premises, including industrial ones, with minimal financial losses. All designs remain same place, construction works for surface finishing are carried out without using additional materials. Leave old water and sewer pipes in the same place, you can remove them old paint and apply a new one. There is no need to try to make them match the wall; on the contrary, use contrasting colors that emphasize the placement of pipelines. If problem areas are identified, correct the problem immediately.

As for the walls, you can remove old plaster to the brick, fill large depressions with cement-sand mortar, but do not level or rub in. Wipe brickwork wire brush, try to highlight the position of each brick. The older the seam and brick, the better, the more modern the loft will be considered. Everything should be simple and natural, no plastic sheathing, plasterboards and other finishing materials.

Professional builders recommend finishing the section of the wall directly next to the bathtub with ceramic tiles, and making the remaining surfaces look like a loft. This approach will allow us to combine modern fashionable design premises while maintaining the usual level of amenities.

Video - Loft bathroom in industrial style

Video - How to save money on bathroom renovations

If you decide to renovate your bathroom yourself, then this review will tell you the correct sequence of actions. Choose the most suitable option carrying out the work and implement it as recommended in the relevant section of the article.

How to organize work

To cope with the work, you need to carefully plan each stage.

The more you understand each stage, the easier it will be to work:

• Thinking through the future interior and choosing plumbing fixtures;
• Dismantling of old finishing and equipment;
• Laying communications;
• Floor finishing;
• Wall decoration;
• Ceiling finishing.

Interior planning

Even before work begins, you need to decide on a number of factors and plan the repair.

The following aspects should be considered at this stage:

• The size of the room - the design directly depends on this. If the room is small, then it comes to the fore rational use space. And if there is enough space, then you can implement any ideas that you would like to see;

• Next, you need to choose the arrangement of plumbing fixtures and furniture elements. You don’t have to be a designer here; the Internet is full of examples that you can use. And you can take ready-made solution, or you can make your own version based on one or several examples to take into account all the features of your bathroom;

• It is necessary to consider whether replacement of plumbing and sewer pipes. Also decide in advance whether the plumbing will be replaced, as this will greatly increase the cost of the project. If a replacement is to be made, then decide in advance on specific equipment options in order to know its size, color and connection method;

• A very important aspect is the planned budget. If you need to carry out repairs quickly and inexpensively, then you should choose materials that are cheap and easy to install. And vice versa, if it is important for you to get the best result and price is not an issue, then you can choose expensive Decoration Materials;
• Be sure to measure the area of ​​all surfaces, this will allow you to accurately calculate finishing materials.

Dismantling old finishes and equipment

This part of the work very often takes longer than the finishing itself. After all, knocking down a tile is much more difficult than laying a new one; the same goes for removing paint and dismantling plumbing fixtures.

Let's look at the most common types of work:

• Most often there are tiles on the floor. The easiest way to remove it is with a hammer drill with a flat blade. The process is noisy and not always simple, especially if the ceramics are held firmly and come off not entirely, but in pieces. It’s much easier if you have linoleum: you just need to remove the baseboard and tear off or simply remove the material from the surface;

• As for the ceilings, they are most often whitewashed or. The first option must be removed using a spatula, after soaking the surface. The second one must be looked at according to the situation and use either special compounds, or heating with a hairdryer, or mechanical treatment;

• As for the walls, they most often have tiles or many layers of oil paint. The first type of coating is knocked down using a puncher or a hammer with a chisel. The second one is best removed using a special composition called paint remover. The remover is applied to the surface and left for a certain time, after which the paint easily comes off the wall; if necessary, individual areas are re-treated;

• Dismantling of plumbing equipment is carried out according to the situation. Often the sides of the bathtub and its supports are concreted, so you need to free the structure using a hammer drill. If the structure is very heavy and remove it from small room problematic, you can cut it into two parts with a grinder. This will make your work easier.

Laying new communications

If, after dismantling old equipment, you have discovered terrible metal water pipes and cast iron sewer elements, it is better to replace them.

The work is done in this order:

• First you need to dismantle all the old pipes. Sewer lines are disconnected at the joints, and water pipes are cut off before the tap, which shuts off the water supply;

• To hide water pipes, it is better to lay them in grooves. The grooves are made in the walls using a perforator according to the size of the pipelines. It is important to mark the location of the grooves in advance so as not to be distracted during the work;

• Sewerage is made from plastic pipes. Thanks to connections with special seals, you can easily assemble the system with your own hands, and it will only take a little time. All turns and branches are made using special corners and bends;

• As for the water supply, it is best to install polypropylene pipes that are connected special soldering iron. If you do not have such equipment, you can hire a specialist. In the bathroom, the amount of work is small, and the price for services will not be very high;

Flooring installation

If you are renovating your bathroom yourself, you should start with the floor. We will analyze two options for carrying out the work: laying linoleum and laying tiles. But first of all, you need to prepare the surface.

The process is done like this:

• The floor is cleaned of dust and debris; if there are large irregularities, cracks and damage on it, it is best to repair them cement mortar. A ready-made dry mixture is purchased, diluted with water and applied to the required areas;
• The easiest way to complete the final leveling of the floor is with a self-leveling mixture. It is prepared and poured onto the surface, after which it is evenly distributed using a needle roller or spatula. It is important to level the plane so that the base is even and smooth, this will simplify further work.

If you decide to make a heated floor, then it is better to fill the surface after laying the pipes or heating modules. Then you won't have to do the screed twice. The process here looks like this: first, the heating system is laid (this process is described in a separate review), after which the solution is poured so that its thickness above the pipes is at least 2 cm.

Now let's look at the fastest option for repairing the bathroom floor:

• You can purchase linoleum, and you should choose options without a base or on a polymer foam base that is not afraid of moisture. It is very important to buy a piece of such a size that you cover the entire surface without seams. The material can have a large width, so there will be no problems with selection;

• The material is spread on the floor and then leveled on the surface. All excess is carefully cut off with a knife at the junction of the wall and floor. The work is simple, but requires care so as not to spoil the material. It is best to cut with a sharp knife with a hard blade;

• Since the room is small, it is not necessary to glue the material. It is much easier to glue double-sided masking tape around the perimeter and secure the linoleum to it. Everything is very simple and at the same time very reliable.

Now let's look at a more reliable option - tiles, which is not only attractive, but also durable.

In this case, the work is carried out as follows:

• The necessary materials are being prepared. In addition to the ceramics itself, we will need adhesive composition and a fugue for grouting;

• The required tools include a building level, a notched trowel, a mixer and a container for preparing the solution. You also cannot do without a tile cutter, since in any case you will have to trim some elements. Crosses will help make all the seams between the tiles perfectly even and neat;

• You can start either from the middle of the room or from the corner of the room. An adhesive composition is applied to the floor, which is leveled using a notched trowel or trowel. One or more tiles are laid, after which their position is adjusted and checked using a level.

• If necessary, individual sections can be lightly tamped with your hand; usually they sit without problems;

• The installation continues on and on. It is important to check the level of both each individual element and the entire surface as a whole. Place the level in all directions so that if there are problems, they can be detected and eliminated in a timely manner; After laying the tiles on the floor, you need to wait for the glue to dry, which usually takes a day. Then the grouting compound is prepared and applied to all cracks. Work is being done rubber spatula

, you must fill the voids between the tiles to protect the surface from moisture. After the fugue has dried, remove its residue from the surface and wash the tiles.

Working with walls

As for this part of the room, here we will also look at two options: PVC panels and tiles. If you need an inexpensive option, then the walls should definitely be covered with plastic panels.

• The work instructions look like this:
• First you need to prepare the walls. If they have large irregularities or cracks, they should be sealed with cement mortar. Mold pockets must be treated with special fungicidal compounds; wooden block for lathing and fastening elements. The tools you need are a level, a hacksaw, a screwdriver and a hammer drill, as well as a tape measure and a pencil for measurements and markings;

• Wall finishing begins with the construction of the frame; for this, level markings are first made to determine the plane of the future frame. Next, the block is cut into pieces of the required size, and holes for dowels are drilled in it every 50 cm;
• Marks are made on the walls, holes are drilled, and the block is attached to dowels, but not fixed. Using a level, the plane of the sheathing is set, slats and chips are placed under it, after which the screws are driven in;

If you have a riser in your bathroom, it is also better to sew it up. To do this, a sheathing is constructed around the pipe.

• Fastening the panels is simple. A starting profile or corner is placed in the corner, after which the first element is inserted. It is positioned with the protrusion forward, so that it can be secured with screws or a stapler at the rear. The work is simple and takes little time, the main thing is to join the elements well before fixing;

• If you did not immediately attach the additional elements, then after installing the panels you need to glue the corners and other components with liquid nails. This will allow you to quickly close all the flaws and give the repair a neat look.

The second option for finishing the walls in the bathroom is laying ceramic tiles.

The process is almost the same as when tiling the floor, but it has its own characteristics, which we will consider here:

• First of all, a strip or metal is fixed around the perimeter at the height of one tile. The laying will begin precisely from this element, this will ensure a perfectly flat plane of the wall, even if there are flaws on the floor. The work is simple: glue is applied to the surface, after which the tiles are glued. Don't forget to put crosses in the seams and check the flatness using a level;

• The next day, the slats are removed and the first row can be added. If necessary, elements are trimmed, and we receive flat wall from bottom to top;

• The final stage is grouting the joints with a fugue. It is important to fill all the seams so that no water gets under the surface.

Ceiling finishing

Now let's figure out how to repair the ceiling. There are three options here if you need cheap repairs, then the easiest way is to use plastic panels (the technology is the same as in the section above).

If you want to get a reliable and attractive ceiling, you can order a stretch fabric. Another inexpensive option is surface putty, which is what we will look at.

The technology of work is simple:

• The materials you need are putty for wet areas, deep penetration primer and paint of a certain color;

• The tools you need are a brush for paint and primer (or a roller), a wide and narrow spatula, a sanding float with sandpaper;
• The work begins with cleaning the surface from dirt and dust. If there are seams on it, then they need to be sealed with a special solution for joints concrete slabs. Mold areas are treated with an antiseptic;
• The ceiling is treated with a primer, this helps strengthen the surface and improve the adhesion of the putty composition. For concrete, a single treatment is sufficient. Work can be continued only after the surface has completely dried;

• The putty is made in two layers. The first is needed in order to eliminate all minor irregularities and apply a more or less uniform layer of putty to the entire surface. The second is the final leveling, and all the flaws of the first layer are eliminated. The work is simple: the spatula is held at an angle of 30 degrees, and the mass is distributed over the ceiling in an even layer;

• After the surface has dried, it needs to be leveled. To do this, use a grater with sandpaper or an abrasive mesh with a grit size of P150 or less. The ceiling is processed in parts to remove all the imperfections of the putty and make the surface perfectly smooth;

To check how well you have leveled the ceiling, simply hold a light bulb or flashlight to it. The light will show any flaws, if any.

• After leveling, dust is removed from the surface. Then a primer is applied to it to strengthen the putty layer;
• Lastly, coloring is done. Use washable paint to make the ceiling easier to care for and resistant to moisture. Most often, painting is done in 2 layers.

If you have completed the finishing of the bathroom, then you can easily renovate the apartment yourself. The main thing is not to be afraid, because the work is only complicated at first glance, in fact, with the right desire, you can complete the room in a week.

Conclusion

I am sure that after reading the article you will already choose the repair option and implement it in the near future. The video in this article will help you understand even better some of the work described above. If you have questions, write them in the comments below.

To do high-quality repairs in the bathroom, you don’t have to have a lot of finances. After all, if you want, you can save a lot of money.

For example, you can refuse the services of a designer and come up with the style in which the renovation will be carried out yourself.

You can also save money on a construction crew and do everything yourself.

But in order for the process to be streamlined and the result to be achieved, it is necessary to draw up a detailed action plan in advance.

So, you will need:

• Come up with a design;
• Stock up necessary materials and tools;
• Make an estimate;
• Calculate the exact dimensions of the bathroom and plumbing dimensions;

When choosing a design, you need to pay attention to the area of ​​the room. Owners of a small area should take into account that a small space is less functional.

Light colors in the interior and large mirrors on the walls will visually enlarge the room.

You can refuse to install a bathtub and give preference to a shower stall. Thus, there will be more space in the room.

For hygiene products, instead of bulky floor cabinets, you can hang compact hanging cabinets.

Once you have decided on a design choice, you need to create an action plan. After all, for the process to proceed continuously, all actions must be performed sequentially.

Negligent attitude towards previous work can significantly affect the final result.

Step 1: Calculate the amount of building materials

This is very important stage under repair. An unpleasant moment may be that if the calculation is not correct, there may not be enough tiles, panels or other building materials.

Indeed, in the process of cutting and laying, some of the material may be damaged. To avoid such an incident, you should initially purchase building materials with a reserve.

Step 2: Remove the old surface

To remove tiles from the walls and tiles from the floor, you need to stock up on a hammer and chisel. However, it will be easier to cope with the work using a hammer drill or drill. There are two options for dismantling: gentle and emergency.

The first is done using a hammer and chisel. First you need to soak the grout, and then carefully separate each tile from the wall or floor.

The second option is much faster, but more dusty and noisy. To do this, you simply need to demolish the coating in layers using a hammer drill.

Step 3: Repairing the floor

First of all, install the screed device. If the installation of an additional “warm floor” system is not provided, then the height of the screed will be 1-1.5 cm. The height will be 3 - 4 cm if the floors are insulated in the future.

There are several types of “warm floor” systems: water, film and electric. Any of the systems maintains the microclimate in the bathroom well, is not expensive and is easy to install.

Step 4: Wall Decoration

Today, the market offers bathroom materials for “any budget.” First of all, it all depends on the finances you have. Most often, tiles are placed on the walls.

But you can choose a more budget-friendly option, for example, plastic panels or special moisture-resistant plaster. At this stage of repair, everything depends on your imagination and finances.

Step 5: Ceiling

When repairing the ceiling, it is worth starting from the materials that were used on the walls. For example, elastic vinyl film looks very nice with tiles and plastic.

If you plan to make a ceiling with various transitions, then use a special moisture resistant drywall. However, there is a more budget option: plastic panels.

After everything is done Finishing work, you can install a bathtub, furniture and plumbing. Do-it-yourself repair is not an easy task, but it is very educational. Plus, this can save you money and make the design exactly the way you want!

DIY bathroom renovation photo

Considered the most expensive. It will be quite difficult to carry out the registration procedure efficiently without resorting to the services of professional companies. However, buyers with a small budget often practice this. For the bathroom you should purchase quality materials, which are able to serve in conditions of high humidity. You need to understand that it is the properties that characterize the purchased goods that will influence the duration of their operation.

After purchasing a new home, any family faces some financial difficulties. That is why the finishing option must be selected rationally to ensure not only a long period of operation, but also a pleasant appearance of the room. Ideally, if everything is done correctly, you can minimum costs get the maximum high-quality restoration premises. Next, we will talk about how to carry out budget repairs of the bathroom and toilet (photo in the article) on your own.

Material requirements

Even if the finishing materials are inexpensive, they must fully comply with all building regulations. This is due to the fact that the microclimate in the bathroom has a number of features that accelerate the wear of materials. When considering a purchase, it is necessary to take into account that in such a room there is high humidity, there is practically no ventilation and there are constant significant temperature changes. That is why all materials used for finishing must have certain qualities. Then the budget renovation of the bathtub and toilet will be 100% successful.

Moisture resistance

You need to understand that any finishing materials that are intended for use in the bathroom must have water-repellent properties. In such a room, the walls and floor will be in contact with moisture, steam and hot air.

The next point to pay attention to is resistance to the formation of fungus and mold. It is advisable to give preference to finishes that have antiseptic additives; they will help prevent the appearance of pathogenic microorganisms. This is due to the fact that the room is constantly humid, so fungus and mold begin to accumulate quite quickly.

Chemical resistance

Impact-resistant finishing materials household chemicals, will become the most optimal solution. Any housewife understands that the bathroom should be as clean as possible, and maintain hygiene without using aggressive detergents impossible. Accordingly, you should choose something that can easily withstand the effects of chemicals. Among the materials that can boast of this property, there are also inexpensive ones, which is especially important when performing budget renovations in the bathroom.

Easy to maintain and install

Another important property is ease of maintenance. When making repairs with your own hands, you need to choose those materials that have a smooth surface that can be easily cleaned of dirt. This will make it easy to maintain order.

When selecting materials and making budget renovations in the bathroom, you must also take into account the ease of their installation. The easier this is done, the more it will be better for the owner. You need to understand that if you have to hire professionals, the cost of repairs may double or even triple.

Wall decoration

This surface has the largest area. As a rule, the most money is spent on decorating the walls. If you want to reduce costs, you need to choose high-quality materials that are not so expensive. Don't rush into purchasing. To save money, you should visit proven shopping centers, stores or seek help from reviews of customers who have already purchased this or that type of finish and tried it in practice. If you want to make a budget renovation in your bathroom, you can’t stop at the first option you come across. At the same time, it is fundamentally important to do right choice in favor of value for money.

Coloring

The most budget and quality option there will be coloring. What is the advantage of this method? The cost is as affordable as possible, and anyone can paint a wall with their own hands. As a rule, moisture-resistant options based on polyester or acrylic base. They are applied in several layers using rollers, brushes or a spray gun. Before applying the material, it is necessary to level the walls, so the painting process can take a lot of time, more than a week. Of the minuses, it should be noted that this type of finish retains fresh look no more than 8 years. In addition, to make the walls look attractive, it is advisable to entrust painting to professionals. It is this finishing method that experts advise resorting to people who want to carry out the most budget-friendly bathroom renovations with their own hands.

Plastic panels

They are also often used in wall cladding. This option is also not included in the list of expensive ones. It's about about paneling. They are made from PVC. If you don't understand what this is, it should be explained. These strips are made of cellular plastic. Their length rarely exceeds 3 m, and their width is 40 cm. They are connected to each other using tenon and grooves. This panel does not require additional leveling of the walls; it can also be glued over the old finish. That is why this option is in demand for budget bathroom renovations.

Ceramic tile

A popular wall decoration option is ceramic tile. It costs more, but it has many advantages. Firstly, the tiles are resistant to mechanical damage, and secondly, it is able to withstand temperature changes and humidity. This option will be excellent for those who do not want to go beyond their budget, but would like to get a fairly high-quality finish. Among inexpensive ones, ceramic tiles of domestic and Belarusian production are in demand.

Priority type of finish

It is worth noting: if there is no opportunity and time to carry out high-quality repairs in the bathroom, and it is urgently needed, then the best option would be to use plastic panels. They are easy to install even for inexperienced people: there is no need to prepare the walls for this process, or to clean the old finish. This material is ideal for budget bathroom renovations. The photo is direct confirmation of this.

Choosing paint for walls

As already mentioned, the bathroom is a rather specific room, so it is necessary to use paints with antibacterial properties and a moisture-resistant effect. Otherwise, the coating may peel off and fungus will quickly appear. The most common paints are silicone, latex, and acrylic. They are inexpensive and have excellent characteristics. It should be noted that water-based mixtures do not have an unpleasant pungent odor, and silicone ones can act as a water barrier.

Traditional oil paints do not have the above advantages. They become cracked quite quickly, so it is better not to use them in the bathroom. Even when carrying out budget renovations in the bathroom, you should avoid such finishing products.

If you want to choose shades other than white, then you should give preference to calm and warm tones. It is advisable to avoid dark ones, since such an option will visually reduce the space. Bright spots and complex patterns will also not bring “zest” to the design. Soft pastel colors will expand the room and additionally fill it with light.

You can choose matte, glossy or semi-gloss paint. The first option will allow you to remove drops and smudges, and such material will also be able to hide all wall defects. What's not suitable for a DIY bathtub renovation on a budget?

Wallpaper selection

It must be said right away that they must be waterproof. When purchasing, you should pay attention to the material. It should not be thin, and you should also inquire about the manufacturing technology. Most often used vinyl wallpapers on a non-woven basis. They are modern, have high performance, are durable, and can withstand exposure to water for a long time. Today it is not difficult to find a suitable decor option. The only disadvantages that should be noted are the high cost, as well as the impossibility of installation with ordinary wallpaper glue: you will have to buy a special mixture.

The second most popular wallpaper is washable. They belong to the cheaper segment, since their characteristics are inferior to the option described above. They are most often used in areas of walls where there is no direct contact with water.

Self-adhesive wallpaper is the most expensive. They are created from polymer film, which is sold in various designs. The disadvantages include not only the cost, but also how difficult the installation is. Moreover, before applying them, it is imperative to make the surface perfectly flat. Another good cladding option for a budget bathroom renovation. A photo of such a finish is included in the article.

Floor finishing

Finishing the floor is also an important task, since the safety of all household members, as well as ease of use, depends on it. Professionals do not recommend using cheap options that do not have surface waterproofing. After all, it is precisely such materials that rarely help with leaks or breakdowns of any household appliances. It should be noted that if the renovation of the home took place quite a long time ago, and the age of the room is more than 30 years, then it is advisable, during the reconstruction of the bathroom, to open up the old floor and completely renew the waterproofing. In this case, coating, painting or roll materials should be used. This also applies to budget bathroom renovation options.

The second most important question is what type of finish to choose. Linoleum is inexpensive. This material works great with mechanical impact, it is wear-resistant, and also pleases with its low price. Like modern version finishing can last at least 15 years, after which it can be changed with maximum ease.

Next, the second most popular among budget-conscious users is tiles. You can buy both ceramic and porcelain stoneware. If your bathroom does not have a large floor area, then you will need very little material for finishing. Due to this, you will not have to spend large sums. This option will remain budget-friendly for those who will carry out the installation themselves.

Professionals say that during renovation, regardless of the limitations in its financing, it is necessary to remove the old floor right up to concrete base. After this, make waterproofing and only then level the surface using a screed. Only in this case will the bathroom be maximally protected from leaks.

Reconstruction

Traditionally, Russian apartments most often use bathtubs rather than showers. This is why the cost of replacing a wash tank can be quite high. They usually make up from a quarter to half of all expenses. Experienced people working in the field of bathroom design notice that it is better not to completely change all the equipment to cheap ones, but to improve the materials that are already available. To do this, reconstruction methods are used that allow you to carry out a budget bathroom renovation with your own hands. What are we talking about?

The bathtub can be re-enamelled. This method will be the most inexpensive, which will not only restore the appearance, but also add shine. Enamel should be applied to the inner surface. You can do this yourself without resorting to the help of professionals. It is best to use a special polyester type composition. Pass the brush two to three times. You can also use a roller or spray gun. In general, this method is suitable for a budget option for renovating a bathtub.

The next low-cost process is restoration with liquid acrylic. Cast iron bath can be restored using this material. You need to apply it to the inner surface using brushes. This method is also called a “fill bath.” It should be noted that it costs more than enamel, but its effect is more lasting.

Repairing a cast iron bathtub is also considered a budget option. This is done by installing acrylic liner. If the product is already in very poor condition, then it can be restored with similar material that is installed in the base of the bathroom. The insert should be glued either with sealant or special glue. It is expensive, but the cost of purchasing such a bowl will be much less than the price of the bath itself.

According to reviews, many give priority to the inexpensive, but quite effective procedure for enameling a bathtub. It allows you to improve the appearance of the product. In addition, this product guarantees a minimum cost, which is ideal for a budget do-it-yourself bathroom renovation.

Repairs take a lot of effort and time, especially if you do it yourself, without involving professional craftsmen in finishing the work. But the biggest impact on homeowners’ budgets is bathroom renovation, since high-quality materials suitable for use in conditions of high humidity are not cheap.

When purchasing a new home, a significant financial burden falls on the family, so it would be rational to find a compromise finishing option that will ensure long-term use and a neat appearance at minimal cost. In this article we will tell you how to carry out budget bathroom renovations on your own.

Material requirements

Even budget finishing The bathroom must comply with strict building standards, since the microclimate in this room has a number of features that lead to accelerated wear of materials. When considering the option of doing the renovation yourself, keep in mind that a bathroom is characterized by high humidity

, insufficient ventilation and temperature changes. Therefore, the materials used to finish surfaces must have the following qualities: Note! Choosing an option inexpensive finishing , be sure to pay attention to the possibility self-installation

material, since hiring professional craftsmen can double the cost of renovating a bathroom.

Wall decoration Bathroom walls have the largest area among the surfaces to be finished, so their cladding accounts for most of the costs. When carrying out repairs yourself in order to reduce costs, you need to take into account that not all materials are suitable for use in rooms with high humidity. There are the following inexpensive ways

wall finishing to protect against moisture: Important! If you need to save time in addition to money when renovating your bathroom, then the best option – . They are easy to install even by an inexperienced technician without preliminary preparation

wall surfaces and removing old finishes.

Floor finishing Finishing the bathroom floor is a fundamental task, the quality of which determines the safety and ease of use of the bathroom. Experienced craftsmen It is not recommended to skimp on surface waterproofing, as it helps to avoid problems with leaks and breakdowns of household appliances. If an apartment from a secondary housing stock is being renovated, and the age of the house exceeds 20-25 years, when renovating the bathroom, you should open the old floor and update the waterproofing trough using rolled, coating or painting materials. As an inexpensive finishing coating

used:

Bathroom renovation

Traditionally, in Russian apartments there are more often bathtubs than showers. The cost of replacing a wash basin can be between a quarter and half of the cost of a budget bathroom renovation. Experienced craftsmen note that if there is a lack of financial resources, it is more rational not to purchase new expensive products, but to discard old cast iron models using one of the following methods:

Note! An inexpensive but effective procedure for re-enamelling a bowl significantly improves the appearance of the product. The most repairable are considered cast iron baths with thick walls.

Video instruction