Do-it-yourself bedspread - step-by-step description of sewing various types of bedspreads (120 photos). How to sew a beautiful and cozy bedspread with your own hands Beautiful bedspreads with your own hands

It is not difficult to sew a bedspread with your own hands if it is in the form of a cover for a sofa or bed made of tapestry fabric. It is much more difficult to sew a quilted bedspread on padding polyester, and even with frills at the bottom of the bed.

In order for the bedspread to become the main decoration of the bedroom, we advise you to take your time and first understand the technology of sewing quilted products. This especially applies to those starting to learn to sew, since tailoring requires not only certain knowledge, but also experience. It is quite difficult to make a quilted pattern so that it is perfectly even without puffs, gathers and seating of the fabric at the intersection of the seams.
If you have never sewn a bedspread, try first sewing a patchwork baby blanket without big size and quilt it. The main thing is to learn how to quilt diamonds or stripes evenly, without seating the top fabric. After this, you will cope with a more difficult task and will certainly be able to sew a beautiful bedspread for a bed or sofa with your own hands.
Calculate the size of the bedspread according to the bed measurements.

Bedspread size.

First, of course, you need to take the correct measurements from the bed or sofa. You need to measure the width, length and height; the bedspread will probably have a long frill. A pleated frill gives the bedspread a finished look and sometimes it becomes the main decorative element of a bed or sofa.
The first three measurements are not difficult to take, the main thing is not to make them too accurate, an addition of 1 - 1.5 cm will not hurt. It is a little more difficult to take into account the angle of the mattress when cutting, because modern beds have mattresses with rounded corners. But this is also quite easy to do, you just need to trace the corner of the bed on paper and then cut it out with scissors.

Now you have all the dimensions to calculate how much you will need for the bedspread and fabric frills, padding polyester and lining. However, don't rush to count. Let's first understand the technology of sewing a bedspread, and then you will find out that for frills you can significantly reduce the fabric consumption.
The only thing that can be said in advance is that if you sew a bedspread with a frill, calculate its height so that it does not “lie” on the floor. Even if it is a few centimeters, there must be a gap to the floor, otherwise the edges will become dirty, and besides, visually the gap between the bedspread and the floor makes the bed higher.
The dimensions of the bedspread may decrease after quilting.

Size after stitching the bedspread.

The main difficulty in sewing a bedspread is that the sewing lines can reach 2 meters or more. And it’s rare that a sewing machine will not “Seat” the top fabric with such a length of continuous stitching. As a result, if you stitch in the form of squares or diamonds, at the intersection of the seams you will have “sags” of the upper fabric. And the finished size of the bedspread itself may decrease because of this.
In addition, you need to stitch once; unraveling the wrong seams is undesirable. On many fabrics, especially satin, cheek tissues there is a mark from needle punctures. This is precisely why I do not recommend sewing a bedspread from expensive satin fabric right away, but rather try to make a “Simpler” bedspread first.

The sequence of sewing a quilted bedspread in the form of step-by-step instructions. Tips on cutting, assembly and design. Selection of materials. Ideas and photos. https://shkola-krasoty.com/stati/kak-sshit-prostyn-na-rezinke

Pallatka_Image (640x480, 148kb).

When performing a stitch on a household sewing machine, the top fabric will still “sag” no matter how much you pull or try. Your “Efforts” will help the sewing machine, but the fabric should not be pulled, but stretched with both hands, so that the needle is always between the hands. Under no circumstances should you pull the fabric in one direction, otherwise the needle may break.
However, the result will be worse smaller sizes diamonds, so it’s better to immediately abandon the small pattern. Large checks or diamonds also look good on a bedspread, and there will be less “Torment.”

Do not cut the fabric exactly to the size of the bed, leaving only seam allowances. Add another 3 to 5 cm in width and length. If they turn out to be superfluous, they can be cut off, but they are unlikely to be superfluous, since the stitching will still shrink the seam. The same applies to padding polyester and lining.
Marking the required size (P 2) of the bedspread can be done already assembled and quilted. And to be on the safe side, before cutting off the excess, follow this line with a securing stitch on your sewing machine and measure the blanket again.
Sewing a bedspread: how to make a quilted pattern.

How to make a quilted pattern.

It is very important to make an accurate calculation of the location of the pattern figures on the bedspread. They should be evenly located over the entire surface of the bedspread, without moving to any side.
You may have to reduce or increase their sizes, but the shapes should start and end strictly from the edge. It is better to first carry out such a calculation on a sheet of paper in a reduced form, for example, on an unfolded piece of paper from a notebook in a box, and then make a life-size model of a rhombus or square and check how it fits on the back side of the fabric, having previously outlined the dimensions of the future bedspread with chalk .

However, this is not the most difficult thing. The most difficult part to mark is the stitch on the right side of the fabric. You can’t mark it with chalk and you can’t use a pencil either; there is only one way left - manually quilt the lines along which the stitching will be done on a machine.
The most “Advanced” way of applying markings to a bedspread is to buy special paper, which sticks to the fabric and, when wetted, is easily removed without leaving traces of glue, but still sweeping away is much “cleaner” and more reliable. Moreover, with the help of a basting you will prevent the top fabric of the bedspread from shrinking as much as possible, and at the same time fix the padding polyester and lining with the top.

It is ideal to make a finishing stitch along the wrong side of the bedspread, that is, along the lining. Then the entire fit will go to the lining, and the front side will be smooth without sags of fabric at the intersection of the stitching. But to make a bedspread stitch in this way you need a good eye and experience, so I don’t recommend this method. By the way, when making stitches, you need to try to tighten, or even more precisely, stretch all the layers of the bedspread, but not so much that the needles on the machine break.
Don't make the checkered pattern or diamonds too small. The larger they are, the easier it will be to sew the bedspread neatly and evenly, and most importantly, it will be easier to cope with the fit of the fabric at the joints.

Bed frill.

Only if you have finally finished quilting the bedspread, the shapes of the patterns and long lines are perfectly even, there are no sag at the joints and the dimensions of the bedspread are almost the same as they were at the beginning, then consider yourself a pro and sew a frill along the edges of the bedspread for you are no longer a problem.
The frill for the bedspread can be sewn separately, in the form of a bed skirt, but basically the frill is sewn to the bedspread and is a permanent part of it, which is largely justified. The non-removable frill makes it easier to process the edges of the bedspread. In addition, even, neat folds of the frill can hide stitch imperfections if your diamonds are far from geometric symmetry.

How to make a frill for a bedspread.

For the frill, you will again have to do a little calculation, namely how to position it and how much fabric will be needed for sewing, taking into account the number and size of the folds.
There is hardly any point in buying an additional piece of fabric 5 meters long for a frill. Its length can be collected by extending the pieces left over from cutting the bedspread. The main task is to ensure that the strips being sewn are cut in one direction. Otherwise, each section of the frill of the bedspread will have its own shade and such a trifle can ruin the entire appearance of the bedspread.
And yet, the connecting seams of the frill stripes should be “Hidden” inside the fold, then they will not be visible.

The fold for the frill of the bedspread needs to be made wide; you should not skimp on this. A width of 10 cm is quite suitable, but you can experiment by making the folds narrower or wider, changing the pitch between the folds, the direction of the folds (counter), etc.
How to sew a frill? There are a lot of ways, including sewing a frill with a double stitch, as shown in this photo.
Source.

Looking at great work skilled craftswomen, sometimes you really want to update your bedroom at home so that your eyes light up! After all, every update of furniture or home decor brings freshness and bright joy into our lives.

Let's take, for example, the same quilted bedspreads for a bedroom set. In the bedroom, this is the most important accented place where we relax from the worries of the day.

Japanese psychologists have long noticed that the color of walls in offices, the appearance of interior design, bedroom decor and others are the strongest irritating factors. Therefore, they advise choosing individually suitable colors of fabrics and patterns for our psyche. It’s not enough to sew something, but to pay close attention to the fabrics and their quality. If you wish, you can buy bed linen from our domestic producers, without being afraid of counterfeiting and non-environmental friendliness. When you know where you can get such high-quality fabrics for sewing bed linen, the problem is almost solved. You can start sewing, dreaming of a future beautiful bedspread. Inspiration and success to you, needlewomen!

Before sewing a bedspread, you need to correctly calculate the fabric.

The cut width is equal to the width of the mattress plus 2 full fall lengths.

The length of the cut is equal to the length of the mattress, plus one full fall length, plus 76 cm (so that the cover covers the bed pillows).

At the end, add 10 cm to the length and to the width. This will give you the opportunity to make a 2.5cm double hem around the entire perimeter of the blanket.

If your fabric is 229cm or 305cm wide, you may not need stitching. However, with narrower fabric, you will need to sew together pieces of fabric for the coverlet. To avoid an unattractive seam in the center, it is better to make one large central section and sew two narrow ones to it on the sides. First of all, determine the final width and length of the bedspread.

See what measurements you need to take to make your own bedspread:

To sew your own bedspreads for a double bed and a double bed increased in width or length, use the full width of the fabric minus 2.5 cm for the seams of both the side parts and the central part. Subtract the center section from the final width of the blanket. Divide the difference into two equal-width side sections.

To make your own bedspread for a single bed, make a central section approximately 102cm wide plus 25cm for seams for the pieces. Subtract 102cm from the final bedspread width. Divide the difference into two equal-width side sections.

Now add the width of the side section, plus 5cm hem allowance, plus 12mm seam allowance; then multiply by two.

If this amount is equal to or less than the width of the fabric, then you will need two panels of fabric - one for the center, two for the sides.

If this amount is greater than the width of the fabric, then you will need three panels of fabric - one for the center and one for each side.

Multiply the length of the bedspread (including the 10cm hem allowance) by the number of panels to determine how much fabric you need for your bedspread.

Sewing a bedspread from scraps is not at all difficult. Any housewife has a lot of materials to create it: it could be old curtains or items of clothing that have not been worn for a long time. The size of the pieces of fabric themselves does not matter. You can make templates or let your imagination run wild. For flaps of the same size, you need to cut out a pattern from cardboard; a square is most convenient, but you can use any shape. Afterwards you need to make a pattern. Paper is placed on the pattern and 5-7 millimeters are added on all sides. Using this paper pattern, cut out the required number of flaps. Then iron the marked seams. To sew two flaps together, you need to place them right sides together and pin them together. It is recommended to sew the elements of the bedspread first in stripes and then across its width. Triangular blanks are sewn together in pairs to form a square. Each seam must be ironed carefully.

Having finished working on the front side of the bedspread, it is sewn together with the lining and filling, if used (for example, batting). To do this, all three layers are placed on top of each other and secured with pins. Sew such a blanket from the center to the edges, making sure that there are no folds. Finally, the edging is done - pre-ironed strips of fabric are sewn along the edges on both sides.

The right fabric texture for a bedspread will complement the design of the entire home. Today, many companies have presented a large range of textiles for the home in their catalogs. Their cost is quite high. But using photographs of models, you can sew a bedspread with your own hands. To make it, home craftswomen choose all kinds of execution techniques. With a sewing machine and ordinary craft tools, you can create a real masterpiece.

A sewn bedspread for a bedroom bed should be in harmony with the interior of the entire room. To do this, you need to choose fabrics whose shades will be combined with each other.

From all the variety, it is better to choose a fabric texture that will harmonize with the curtains. Then the textile ensemble will be complete. Let's consider detailed description DIY bedroom bedspread technique.

Patchwork

Products made in patchwork style immediately transform the room. It creates a playful, cozy, positive atmosphere. Intricate patches sewn into a single composition are often used to decorate the beds of girls and boys. The creation process can be divided into stages:

• Design project ─ first you need to develop the design of the future bedspread from scraps. You can use ready-made options, or you can create your own project;
• Prepare the details ─ you need to be extremely careful and precise in the calculations and preparation of the parts. They can be square, diamond, rectangular or have other shapes, as well as plain or colored;
• Sewing the Pieces ─ This step of the job requires patience, pins and an iron. The parts are sewn strictly according to the presented sketch of the product;
• Iron the resulting front part of the bedspread;
• Sew the front side to insulation, fleece, synthetic padding, dense material or other selected fabric;
• Stitch the resulting double layer to the main bottom fabric;
• Final finishing ─ you can use edging or other finishing material.

Even a novice craftswoman can make a bedspread using the patchwork technique with her own hands. The main thing is the ability to use a sewing machine.

Cutting the shreds

Arrange the shreds in the desired sequence

Sew the patches

Hemming the padding polyester

Fastening the layers

Ready product

With puffs

The puffed bedspread is a luxurious product. It can only be sewn by an experienced needlewoman who is capable of performing delicate and painstaking work. Puffs are folds that are created using drawn lines on the fabric. Stitches are made in the designated places, which are then pulled together. The result is interesting solutions for folds in the material. Stages of work:

• Choice of material ─ a puffed bedspread looks chic made from satin, silk or other smooth, shiny fabrics. They drape easily, and the folds on the shiny material have a luxurious look;
• Selecting a puff pattern ─ from large quantity buffs, you need to choose “yours”;
• Calculation of material ─ to make a bedspread with puffs, you need to determine the amount of material. To do this, take the size of the fabric (50x50 mm, 100x100 mm) and make puffs, filling the entire material with them. Then a repeat measurement is made and the reduction factor is calculated. It will be needed to determine the amount of fabric per bedspread;
• Prepare front and lining fabric;
• On the wrong side of the main fabric, apply a pattern of puffs with the direction of the stitches;
• Make stitches according to the intended patterns;
• Pull the puffs;
• Fold the main and lining fabric with the wrong sides inward, and stitch the outer edges;
• Decorate the edge of the bedspread with flounces, ruffles or ruffles.

Making the markings

Connecting the lines

We pull them together

Making a few zip ties

Finished work

Quilted

A quilted bedspread with padding polyester and lining material will decorate the room and suit any style. For sewing bedspreads, it is better to use satin or silk material. You need to be careful and attentive in your work. Stages of work:

• Decide on the size of the bedspread ─ to do this, measure the width, length of the bed, as well as the height of the frill, taking into account the increases;
• Determine the size of the cells or diamonds. You need to remember ─ the smaller the pattern, the more fabric will be used for the product. Therefore, you need to make an extra increase in material on all sides of the bedspread by 5-10 cm. Excess allowances can always be cut to the desired size of the product;
• Use running stitches to follow all the intended lines, since the chalk will be erased, and it is not advisable to use a pencil for expensive and delicate fabrics;
• Place the stitch next to the basting seams;
• Finishing seams when crossing should not form an “overflow” of material. Stitch only once. For example, satin does not tolerate repeated stitching, since needle punctures will be visible on the material after the stitching is unraveled;
• Quilting the bedspread ─ on the assembled and quilted product, the final marking of the bedspread is performed, which depends on the processing of the cuts. For example, the edge can be decorated with a hem seam, bias tape, ruffles or folds;
• Cut off the strip for the frill. It is sewn separately in the form of a skirt. If the trim will have folds, then you need to calculate their depth and the length of the entire frill. For example, if the length of the frill is 8 m 40 cm, then to the depth of the folds, with a width of 3 cm, you need to add 2 m 80 cm. Then sew it to the bedspread. The cut can be overlocked or processed with bias tape;
• With a frill, the product will have a finished look.

The next step is to calculate the amount of fabric needed for a sofa cover. To do this, you need to measure the length and width of the sofa and determine the optimal length - whether the blanket will cover only the seat, or the entire furniture, including the armrests and legs. Don't forget to add a few centimeters (about 5) to the allowances on the sides of the parts. A pre-prepared pattern will help you avoid making mistakes in your calculations.

Having watched at least one master class that provides guidance on sewing bedspreads, you will probably want to repeat it, adding some color to your room. In addition, homemade interior decorations have been at the peak of fashion for many years.

Bedspreads on corner sofa usually have a more complex shape, so it is advisable to first mentally divide the sofa into two parts and measure the dimensions of each of them, adding allowances for connecting the parts of the cape. Of course, it is more difficult to make a blanket for a corner sofa with your own hands than for a regular one, but it will be all the more pleasant to achieve your goal.

The selected fabric should be pre-washed and ironed to avoid disappointment if the fabric shrinks too much. And you can sweep the cut out parts directly onto the furniture - this way you will immediately see minor flaws in the pattern and be able to correct them in time. But you will have to sew them together on a typewriter.

Bedspread for a corner sofa

Step-by-step instructions on how to sew a bedspread for a sofa will be useful for beginning craftswomen and can be found on the Internet or in books.

Even a simple rectangular blanket for a sofa in the kitchen will add coziness to the interior, and several soft pillows from the same fabric will become a highlight of the design.

Adding fringe and ruffles will not only help cover up the worn legs and edges of the sofa, but will also make the throw look even more beautiful. And if you decide to maintain a more formal style, choose a fabric similar to that used for upholstering the sofa and slightly reduce the size of the bedspread. A drawstring sewn along the edges with a missing elastic band will allow you to secure such a cover to the furniture. In this case, the function of the cover will be purely utilitarian - it will protect the sofa from being wiped out.

• Double-sided cotton fabric with a beautiful pattern 280 cm wide for the top of the bedspread
• Sintepon with a density above 150g/m2, thickness 3-4 mm
• Linen or cotton fabric for lining
• Fabric for piping
• Stitch template 23x23 cm
• Long ruler
• Chalk or fabric marker
• Scotch
• Threads, needle

Before starting work, all fabrics for the future bedspread must be washed in washing machine on the mode in which it will be washed later, or steam it well with an iron. This is done in order to prevent shrinkage and distortion of the finished product.

Due to the large size of the bedspread, it is best to work on a clean floor, carefully laying the fabric around the perimeter.

1) For the upper part of the bedspread or, as it is otherwise called, the top, double-sided cotton fabric with beautiful pattern rope loops. It is better to take fabric for the top of sufficient width in order to eliminate seams and irregularities. A square for a top measuring 230x230 cm is cut out of the fabric, the edges of which are overlaid.

2) For the backing - the lining of the bedspread, take linen or cotton fabric 150 cm wide, from which a square slightly larger in size than the top, 240x240 cm, is assembled. Iron the seam allowances in opposite directions, overlay the edges of the backing.

3) To mark the square stitch of the bedspread, take a 23x23 cm template and a long wooden ruler. Using a marker or chalk, line the stitches on the wrong side of the fabric, starting from its edge. For more convenient work, the fabric is secured with tape so that it does not move or shrink during ruling.

4) After the entire surface of the fabric is covered with identical lined squares of 23x23 cm, the top is removed to the side.

5) Take linen fabric for the backing, lay it flat on the floor with the wrong side up and secure it with tape.

6) The padding polyester is laid on the backing fabric in sheets that are connected to each other with sparse, loose stitches.

7) A cotton top is placed on top of the laid synthetic padding, with the top lined. Be sure to make sure that the fabric lies flat, without folds or creases.

8) Using light threads and a needle, temporarily connect all parts of the bedspread; it is better to start stitches from the center, first in one direction and then in the other. In the photo, the red lines show the ruling and the future stitch, and the green lines show the temporary basting. The basting is done without knots so that when removing it, the structure of the fabric of the bedspread and the stitching are not disrupted.

The process of basting stitches is long and labor-intensive, but it is necessary to create an even machine stitch without creases or wrinkles. Instead of basting with a thread and a needle, you can use special bent pins for quilting; such pins do not move or move during the sewing process, which will not affect the quality of the stitch.

9) Machine stitching starts from the center to the edges of the blanket. To do this, the edges of the bedspread are folded towards the center, the bedspread folded in this way is placed along its entire length in an additional place next to the machine. First, horizontal lines are laid, then vertical ones, alternately filling the entire space of the product.

The stitch is laid exactly along the lined line, left hand slightly stretches the fabric behind the sewing foot, and the right one in front of the foot.

10) The sides of the bedspread are aligned using a ruler and a fabric marker, and the corners are aligned using a square. Then a line is sewn as close to these lines as possible. Excess fabric is cut off with scissors.

11) The edges are edged with a 3 cm edging made of cheerful striped fabric in nautical style. The edges of the allowances of strips of edging fabric 10 cm wide are ironed using a cardboard template prepared in advance.

The piping is sewn along the entire perimeter of the bedspread, the bedspread is completely ironed.

That's it, a quilted bedspread in marine theme ready, you can make your bed with it or wrap yourself up with pleasure on a cool evening.

Video DIY bedspread - #blanket Plaid part1.

When you do not have sufficient sewing experience, taking on a responsible job is always scary. Especially if the choice fell on complex fabrics or bedspread patterns. In this case, an excellent option would be to sew a trial version yourself.

Anyone can create a beautiful bedspread with their own hands, the main thing is to charge yourself with a lot of desire.

This is a great way to create a beautiful bedspread from simpler materials, practice making even seams, laying folds, stitching, and taking into account the pattern.

ADVICE. A good training option would be a patchwork-style bedspread. This technique requires painstaking work, but it provides invaluable experience.

A children's blanket complemented with accessories-toys in the same theme.

Finished products can be used in the country house or in a children’s room. The skills of creating a bedspread with your own hands will undoubtedly come in handy in the future. The question of how to sew a bedspread will no longer arise.

Sleeping beds can be complemented with bedspreads that match the aquatic color scheme with the bed linen.

Sewing a bedspread with your own hands is not such a difficult task. This will require a little time, effort, and skills. Accurate calculation and patience guarantee a beautiful and cozy bedspread.

Textiles – essential element decoration of any room. In the bedroom, the main “semantic center” is the bed, so its design is given highest value. Luxurious drapery of a sleeping area will instantly transform the entire room. Creating a beautiful bedspread with your own hands is not at all difficult if you have the right materials, tools and enough patience.

Functional significance of bedspreads

A bedspread is not only a bed decoration, but also a very functional item. It protects bed linen from dust, dirt, abrasion, and keeps it fresh. There are also blankets that serve as both a protective drapery for the bed and a “day blanket” under which people sleep without making the bed. The product makes the room cozy and the atmosphere itself “homey”.

Blankets of various models are used not only in the bedroom, but also for sofas, armchairs located in the living room, hallway, kitchen, etc.

Fabric selection

The fabric for the bedspread is matched to the rest of the room decoration. Most often used:

• wool - pure wool types of material are expensive and weigh a lot. That’s why mixed ones are often used - they are a little lighter, easier to care for, and decorated with bright patterns;
• acrylic – bright, fluffy, light, practically non-shrinking. Dries quickly, lasts a long time, ideal for children's bedrooms;
• tapestry - dense, heavy, usually motley. Not suitable for small beds, cramped rooms, look great in “classic” living rooms;
• velvet is luxurious, expensive, but wears out quickly. Its use is appropriate if there are one or two more velvet elements in the room;
• bamboo, cotton are thin, lightweight, easy-to-wash materials, to which polyester is often added. The best option for a summer blanket;
• viscose - is cheap, is an artificial fabric, but in many properties it is equal to natural, and after washing it shrinks;
• silk - thin, smooth, the best way suitable for “oriental” interiors. It fades quickly in the sun, wash it by hand or on a delicate cycle;
• faux fur – looks chic, is made mainly from synthetic materials, is highly electrified, and difficult to care for;
• plush, fleece - used as blankets for newborns, as well as older girls and boys. The fabric is very soft, but requires the most careful washing, shrinks, and is sometimes used as a lining;
• padding polyester – used for making quilts and bedspreads exclusively as a lining.

If there are allergy sufferers among the residents, this factor is taken into account when choosing fabric. If you have pets or small children, preference is given to the most non-staining materials.

Selecting the color

A well-chosen color and pattern on the bedspread will help to slightly correct the unfortunate shape of the room and diversify it. Cold, dark shades used in spacious, well-lit rooms, with windows facing southeast, south. Lighter, warmer ones are suitable for small bedrooms where the sun rarely penetrates, and the windows are “turned” to the north, northwest.

Stripes directed in the right direction can correct the disproportion of the room, but it is advisable to duplicate the print on other elements of the decor. If the wallpaper, carpets, curtains are colorful, the bedspread is selected in a single color and vice versa. Sometimes the drapery of the bed is made the only color accent of a monochrome interior. Two- or three-color models are most common; overly variegated ones are suitable only for interiors such as boho or oriental.

Most popular colors:

• purple-black;
• slate gray;
• beige;
• terracotta;
• silver brown;
• brilliant blue;
• mahogany;
• golden orange;
• pale pink;
• rich brown;
• creamy white;
• chrome green;
• orchid.

Model selection

The model of a blanket or bedspread is selected based on the style of the bedroom interior, the design of the bed itself, the upholstery and decor of the rest of the furniture. Many people choose a blanket for curtains - this option is ideal for classic, Gothic, and antique interiors. Both the curtains and furniture draperies here are made of the same material - tapestry, velvet, velor, and the pattern on them is duplicated.

Models with edges that hang down to the floor look beautiful on large double beds. A valance often peeks out from under the thick drapery. The single bed of a teenage boy is decorated more modestly - only the bedspread hides the bedspread. Such options are suitable for the styles of minimalism, hi-tech, and Japanese. For the romantic interior of a girl's bedroom, a thin bedspread with ruffles, lace, flounces, and puffs is created.

The cover-cover tightly fits the upper part of the structure, its dimensions are selected to match the dimensions of the mattress, taking into account the fact that the latter will accommodate bed linen and a blanket. Sometimes an elastic band is sewn to such a thing. This is an ideal option if the wooden parts of the bed are “rich” with textured carvings, paintings, or the bed is made entirely of rattan.

When the bedspread is decorated with a valance, a similar element is duplicated in the design of the dressing table, armchairs, and chairs. Tassels, fringes, frills, beads, rhinestones, bows are usually placed along the contour of the product so that they do not interfere with sitting and lying on it.

Calculation of fabric consumption

The consumption of material depends on the dimensions of the sleeping place, the height of the bed, and the model of specific drapery. For the simplest, square or rectangular option, measure the width and length of the upper part, adding 1.5-2 cm for folding edges, 20-50 cm for hanging edges. It is permissible to make a bedspread for a double bed from several pieces of narrow fabric if the craftsman is not embarrassed by the seams located in the most visible places.

If you plan to have a lot of folds and puffs on the blanket, the material consumption will increase by 20-40%. If there is a valance, it will use a long, narrow piece, usually cut to length. The calculation of matter here is simple - you need to measure the perimeter of the top of the bed, adding to it from 50% to 150%, depending on the depth and number of folds. A quilted blanket will also require a little more fabric than a smooth blanket made from a single piece of fabric. When it is necessary to “adjust” parts according to the design, the material is purchased with a margin of up to 10-25%.

Additional decor in the form of frills, bows, textile flowers will require additional material. Its volume depends on the quantity decorative elements, most often a fabric of a different color and texture is used.

Manufacturing techniques

There are many options for making bedspreads. This is patchwork, knitting, weaving. The item is made from a single piece of fabric or many small pieces; it can be knitted either from threads or from narrow textile ribbons. Wicker and knitted products give the room coziness and warmth; a thick lining is usually sewn onto them so that the product is not see-through.

Patchwork

Patchwork is a patchwork technique that involves a very painstaking work process, but surprises with its magnificence. The product creates a cozy atmosphere, transforming the room.

How to sew such a thing step by step:

• First, the design of the object and the shape of its parts are thought out;
• several pieces of different matter are selected;
• details are cut out - they will be square, in the shape of rhombuses, triangles, hexagons, asymmetrical elements of one or more colors;
• stitching is carried out according to the pattern, after preliminary fastening with pins;
• Afterwards, it is advisable to iron the front part of the product and stitch the resulting fabric to padding polyester, fleece, satin or other suitable material;
• then the two-layer blanket is sewn to the bottom fabric;
• at the very end, edging is done with bias tape, in another similar way.

With puffs

Puffs are a type of folds and creases in drapery. To sew such a chic product you will need a lot of time and patience. Puffs are formed from clearly drawn lines and stitches on the fabric, which are subsequently neatly pulled together, forming a three-dimensional pattern on the fabric.

How to make a bedspread with puffs:

• is selected suitable material. Such patterns look best when made of silk, satin, or other shiny, smooth material that drapes easily;
• Next, they select a pattern - there are a lot of options here. These are “flowers”, “braids”, “braids”, “bamboo”, etc.;
• The calculation of the material here is very individual. To determine the quantity, take a small piece of fabric, fill it with the selected pattern, and calculate the size reduction factor;
• Next, the lining and outer material are prepared;
• from the inside, a pattern of puffs is applied, according to which the stitches are made;
• the puffs are carefully pulled together, the front and lining fabrics are folded “face to face”, the edges are ground down;
• the product is turned inside out. The edges are decorated with frills, flounces, and ruffles.

Quilted

A quilted bedspread will become a real “highlight” of the bedroom; it is original and distinctive. The ideal material for it is silk or satin.

Progress:

• to determine the exact dimensions of the product, measure the length, width, height of the bed, adding allowances for seams and frills;
• The smaller the pattern is supposed to be, the more material will be required. An additional 5-7 cm in each direction is usually sufficient;
• all the necessary lines are marked with long stitches, a line is laid along them;
• when making finishing seams, there should be no “sagging” of fabric;
• the assembled product is decorated at the edges with hem seams, frills, bias tape, etc.;
• if there are frills, calculate the number of folds per unit length, sew the gathered strip to the blanket, and cut the edges using an overlocker.

Knitting needles

An item knitted with knitting needles fills the room with comfort and warmth. This type of blanket is either continuous or made up of separate pieces. The first option is created from wool or synthetic colored threads. Before starting knitting, it is advisable to knit a small sample, with the help of which it is determined how many loops there are per 1 or 10 cm. Using the selected pattern, knit a piece measuring at least 10 by 10 cm, the measurement is carried out with a ruler. The approximate number of loops for a double bedspread is 450-500, the number of rows is 550-700.

A product assembled from fragments of the same or different shapes, looks the most original, especially if the parts are multi-colored. For example, for a checkerboard blanket, you will need to cast on 35-37 loops and knit about three dozen rows - their number depends on the density of the knitting. If the size of the resulting square is 12 by 12 cm, then you will need to knit 136 black and the same number of white squares. The outline of the product is decorated with a knitted strip.

Crochet

Crocheting a blanket is no more difficult than knitting. Knitting is done from the edge, but most often - according to the “granny square” principle, that is, from the center to the edge.

How to perform a granny square:

• four air loops are cast and connected into a ring;
• then three lifting stitches, two double crochets, three double crochets. The report is repeated three times;
• at the beginning of the row, find the third loop, make a connecting one with it;
• in the next row everything is repeated;
• then pick up three lifting loops to make the corners, perform the cycle “three double crochets plus three air loops, plus three double crochets”;
• one side of the square - three double crochets under the chain loops of the previous row plus two chain loops;
• then the pattern is continued, double crochets are tied into the interstitial holes of the previous rows;
• when the square has reached the desired size, it is tied with a bright thread;
• The individual elements are connected with a loop seam.

Master class - how to sew a quilted bedspread with your own hands

Self-sewn bedspreads are made from various materials– curtain, furniture, dress fabric, and sometimes two or more are used simultaneously. If there is a lining, special material will be required for it.

To begin with, purchase satin fabric or taffeta, non-woven fabric, cheap textiles for the bottom fabric, and lining. If the width of the bed is about 135 cm, then a fabric width of 150 cm is enough, since the design of the cuts and the increase will take 3-4 cm. The length of the cut is 210-220 cm, if frills are expected, the perimeter of the blanket is multiplied by 2.3-2.7 . If such a bedspread is sewn from squares measuring 13 by 13 cm, 323 parts will be required.

Necessary tools, equipment

To properly sew a blanket, you will need:

• measuring tape or tape measure - for measuring the bed;
• pencil, ruler, square, patterns - to create a pattern;
• iron, ironing board - for straightening textiles and forming folds;
• sharp scissors - for cutting out all elements;
• fabric chalk or a piece of soap - for transferring the pattern to the fabric;
• invisible pins - to secure individual parts;
• needles, threads, thimble, overlock, sewing machine– for direct sewing.

Pattern drawing, cutting

For complex models you will need to create the appropriate patterns. In this case, the width, length, and height of the bed are measured. Dimensions are scaled and transferred to a squared piece of paper or graph paper. When creating patterns, all elements are carefully drawn, the location of decorative elements and seam allowances are taken into account.

If the product is ordinary quilted, the lines of future seams are marked on the drawing. When an object is made up of many parts, pieces of the same or various shapes, then seam allowances are taken into account for each element.

Sewing

A properly sewn bedspread drapes beautifully on the bed, does not bulge or pull together.

It is permissible to decorate a quilted blanket with puffs. How it's done:

• draw a circle with a diameter of 15 cm on paper;
• it is folded in half twice to get four sectors;
• lines are drawn at the fold points, exactly in the middle between them, and more lines are drawn through the center;
• then cut out the concave-convex-concave-convex parts of the pattern and transfer it to the fabric;
• in total there will be about 146 elements on the bedspread, each of which is pinned, basted, and pulled together;
• then the base, lining, and frill are sewn to the top panel. Sections of the latter are decorated with bias tape or overlock.

Decorating - bedspread design ideas

You can decorate a freshly sewn bedspread in a variety of ways:

• ruffles, flounces, gathers;
• voluminous flowers, bows;
• balls, knitted hearts;
• decorative pillows;
• ribbons, rhinestones;
• grabs, clamps.

The more diverse, lush, and bright the decorative elements are made, the more beautiful the design will be. Frills create a romantic atmosphere, pillows create coziness, tassels create a solemn look. It is important not to use all the details at once - this option is only permissible in kitsch and boho style interiors.

How to sew a blanket from old jeans

A dozen old jeans will also make an excellent bedspread for a modern sofa or bed. This material very strong, abrasion resistant. You can only use whole pieces, without defects or abrasions; it is advisable to use parts of the same shade, but alternating contrasting elements in a checkerboard pattern is acceptable.

Sewing a product begins with cutting out the material - all pants are cut into squares of the same size. Each square is overcast, the edges are tucked, after which all the elements are sewn together. It is also possible to use elements of different shapes, but this option is quite complicated. It is important to adhere to a uniform stitching technique:

• “quick squares” - take two different fabrics, cut out two rectangles from them, sew them together with the long sides, and steam the seam with an iron. A rectangle is also cut out from the third piece of contrasting material, which is sewn to the workpiece. These blocks make very original patterns;
• “stripes” - the parts are identical stripes, sewn together according to a previously drawn pattern or one found on the Internet;
• "watercolor" - a technique based on playing with color. The elements are connected by color, forming a gradient transition. The difficulty is that you will need a lot of jeans in different shades;
• “chaotic patchwork” - all the details are multifaceted, asymmetrical, multi-colored. The idea is optimal for cases when there are a lot of small flaps, but cutting them into identical fragments is not possible. This technique is complex and requires experience and patience.

Conclusion

It’s not difficult to sew or knit a bedspread in any style yourself if you know exactly what you should get in the end. Step-by-step instructions with photos and videos are easy to find on the Internet. From the scraps and pieces of thread remaining after creating the bed drapery, showing imagination, children's toys and all kinds of small decor are made.