Drawing a design on a printed circuit board with a marker. A simple way to make printed circuit boards (not LUT)
On the pages of the site there has already been talk about the so-called “pencil technology” for manufacturing printed circuit boards. The method is simple and accessible - a correction pencil can be bought in almost any store that sells stationery. But there are also limitations. Those who tried to draw a printed circuit board drawing using a correction pencil noticed that the minimum width of the resulting track is unlikely to be less than 1.5-2.5 millimeters.
This circumstance imposes restrictions on the production printed circuit boards, which have thin tracks and a small distance between them. It is known that the pitch between the pins of microcircuits made in a surface-mount package is very small. Therefore, if you need to make a printed circuit board with thin tracks and a small distance between them, then the “pencil” technology will not work. It is also worth noting that drawing a picture with a correction pencil is not very convenient, the paths are not always smooth, and the copper patches for sealing the leads of radio components are not very neat. Therefore, you have to adjust the printed circuit board design with a sharp razor blade or scalpel.
A way out of this situation may be to use a PCB marker, which is perfect for applying an etch-resistant layer. Unknowingly, you can purchase a marker for writing inscriptions and marks on CDs/DVDs. Such a marker is not suitable for the manufacture of printed circuit boards - a ferric chloride solution corrodes the pattern of such a marker, and the copper traces are almost completely etched. But, despite this, there are markers on sale that are suitable not only for writing inscriptions and marks on various materials(CD/DVD discs, plastic, wire insulation), but also for making an etching-resistant protective layer.
In practice, a marker for printed circuit boards was used Edding 792. It allows you to draw lines 0.8-1 mm wide. This is enough to make large quantity printed circuit boards for homemade electronic devices. As it turned out, this marker copes with the task perfectly. The printed circuit board turned out pretty good, although it was drawn in a hurry. Take a look.
PCB (made with Edding 792 marker)
By the way, the Edding 792 marker can also be used to correct errors and blots that occurred when transferring a printed circuit board design to a workpiece using the LUT (laser ironing technology) method. This happens, especially if the printed circuit board is quite large sizes and with a complex pattern. This is very convenient, since there is no need to completely transfer the entire design onto the workpiece again.
If you can’t find an Edding 792 marker, it will do Edding 791, Edding 780. They can also be used to draw printed circuit boards.
Surely, novice electronics enthusiasts are interested in the technological process of making a printed circuit board using a marker, so the next story will be about this.
The entire process of manufacturing a printed circuit board is similar to that described in the article “Making a printed circuit board using the “pencil” method.” Here's a short algorithm:
A few "subtleties".
About drilling holes.
There is an opinion that you need to drill holes in the printed circuit board after etching. As you can see, in the above algorithm, holes are drilled before etching the printed circuit board in the solution. In principle, you can drill either before etching the printed circuit board or after. From a technological point of view, there are no restrictions. But, it is worth considering that the quality of drilling directly depends on the tool used to drill holes.
If the drilling machine develops good speed and there are high-quality drills available, then you can drill after etching - the result will be good. But, if you drill holes in the board with a homemade mini-drill based on a weak motor with poor alignment, you can easily tear off the copper spots under the terminals.
Also, a lot depends on the quality of PCB, getinax or fiberglass. Therefore, in the above algorithm, drilling holes occurs before etching the printed circuit board. With this algorithm, the copper edges remaining after drilling can be easily removed sandpaper and at the same time clean the copper surface from contaminants, if any. As is known, the contaminated surface of copper foil is poorly etched in solution.
How to dissolve the protective layer of the marker?
After etching in a solution, the protective layer, which was applied with an Edding 792 marker, can be easily removed with a solvent. In fact, white spirit was used. It stinks, of course, disgustingly, but it washes off the protective layer with a bang. There are no varnish residues left.
Preparing a printed circuit board for tinning copper tracks.
After the protective layer is removed, you can for a few seconds throw the printed circuit board blank into the solution again. At the same time, the surface of the copper tracks will be slightly etched and become bright pink. Such copper is better covered with solder during subsequent tinning of the tracks, since there are no oxides or small contaminants on its surface. True, tinning of the tracks must be done immediately, otherwise the copper in the open air will again be covered with a layer of oxide.
Finished device after assembly
Printed circuit board– this is a dielectric base, on the surface and in the volume of which conductive paths are applied in accordance with electrical diagram. The printed circuit board is designed for mechanical fastening and electrical connection between each other by soldering the leads of electronic and electrical products installed on it.
The operations of cutting out a workpiece from fiberglass, drilling holes and etching a printed circuit board to obtain current-carrying tracks, regardless of the method of applying the pattern to the printed circuit board, are performed using the same technology.
Manual application technology
PCB tracks
Preparing the template
The paper on which the PCB layout is drawn is usually thin and for more accurate drilling of holes, especially when using manual homemade drill so that the drill does not lead to the side, it is necessary to make it more dense. To do this, you need to glue the printed circuit board design onto thicker paper or thin thick cardboard using any glue, such as PVA or Moment.
Cutting the workpiece
A blank of foil fiberglass laminate of a suitable size is selected, the printed circuit board template is applied to the blank and outlined around the perimeter with a marker, a soft pencil or marking with a sharp object.
Next, the fiberglass laminate is cut along the marked lines using metal scissors or sawed out with a hacksaw. Scissors cut faster and there is no dust. But we must take into account that when cutting with scissors, fiberglass is strongly bent, which somewhat worsens the adhesion strength of copper foil and if the elements need to be re-soldered, the tracks may peel off. Therefore, if the board is large and has very thin traces, then it is better to cut it using a hacksaw.
The template of the printed circuit board pattern is glued to the cut-out workpiece using Moment glue, four drops of which are applied to the corners of the workpiece.
Since the glue sets in just a few minutes, you can immediately begin drilling holes for radio components.
Drilling holes
It is best to drill holes using a special mini drilling machine with a carbide drill with a diameter of 0.7-0.8 mm. If mini drilling machine is not available, you can drill holes with a low-power drill using a simple drill. But when working universal hand drill The number of broken drills will depend on the hardness of your hand. You definitely won’t be able to get by with just one drill.
If you cannot clamp the drill, you can wrap its shank with several layers of paper or one layer of sandpaper. You can wrap a thin metal wire tightly around the shank, turn to turn.
After finishing drilling, check whether all holes are drilled. This can be clearly seen if you look at the printed circuit board up to the light. As you can see, there are no missing holes.
Applying a topographic drawing
In order to protect the places of foil on fiberglass laminate that will be conductive paths from destruction during etching, they must be covered with a mask that is resistant to dissolution in an aqueous solution. For the convenience of drawing paths, it is better to pre-mark them using a soft pencil or marker.
Before applying the markings, it is necessary to remove traces of the glue that was used to glue the printed circuit board template. Since the glue has not hardened much, it can be easily removed by rolling it with your finger. The surface of the foil must also be degreased using a rag using any means, for example acetone or white alcohol (the so-called purified gasoline), or any detergent for washing dishes, for example Ferry.
After marking the tracks of the printed circuit board, you can begin to apply their design. Any waterproof enamel is well suited for drawing paths, for example alkyd enamel PF series, diluted to a suitable consistency with white alcohol solvent. You can draw paths with different tools - a glass or metal drawing pen, a medical needle, and even a toothpick. In this article I will tell you how to draw circuit board traces using a drawing pen and ballerina, which are designed for drawing on paper with ink.
Previously, there were no computers and all drawings were drawn with simple pencils on whatman paper and then transferred with ink to tracing paper, from which copies were made using copiers.
Drawing begins with contact pads, which are drawn with a ballerina. To do this, you need to adjust the gap of the sliding jaws of the ballerina drawing board to the required line width and, to set the diameter of the circle, perform the adjustment with the second screw, moving the drawing blade away from the axis of rotation.
Next, the ballerina's drawing board is filled with paint to a length of 5-10 mm using a brush. For applying a protective layer to a printed circuit board, PF or GF paint is best suited, since it dries slowly and allows you to work quietly. NTs brand paint can also be used, but it is difficult to work with because it dries quickly. The paint should adhere well and not spread. Before painting, the paint must be diluted to a liquid consistency, adding a suitable solvent to it little by little with vigorous stirring and trying to paint on scraps of fiberglass. To work with paint, it is most convenient to pour it into a bottle of manicure varnish, in the twist of which there is a solvent-resistant brush.
After adjusting the ballerina's drawing board and obtaining the required line parameters, you can begin to apply the contact pads. To do this, the sharp part of the axis is inserted into the hole and the base of the ballerina is rotated in a circle.
With the correct setting of the drawing pen and the desired consistency of paint around the holes on the printed circuit board, perfectly round circles are obtained. When a ballerina begins to paint poorly, the remaining dried paint is removed from the gap of the drawing board with a cloth and the drawing board is filled with fresh paint. To draw all the holes on this printed circuit board with circles it took only two refills of the drawing pen and no more than two minutes of time.
Once the round pads on the board are drawn, you can start drawing the conductive paths using a hand drawing pen. Preparing and adjusting a manual drawing board is no different from preparing a ballerina.
The only thing additionally needed is a flat ruler, with pieces of rubber 2.5-3 mm thick glued to one of its sides along the edges, so that the ruler does not slip during operation and the fiberglass, without touching the ruler, can freely pass under it. Best suited as a ruler wooden triangle, it is stable and at the same time can serve as a hand support when drawing a printed circuit board.
To prevent the printed circuit board from slipping when drawing tracks, it is advisable to place it on a sheet of sandpaper, which consists of two sandpaper sheets sealed together with the paper sides.
If they come into contact when drawing paths and circles, then you should not take any measures. You need to let the paint on the printed circuit board dry until it does not stain when touched, and use the tip of a knife to remove the excess part of the design. In order for the paint to dry faster, the board should be placed in a warm place, for example in winter time to the heating battery. IN summer time years - under the rays of the sun.
When the design on the printed circuit board is completely applied and all defects are corrected, you can proceed to etching it.
Printed circuit board design technology
using a laser printer
When printing on a laser printer, the image formed by the toner is transferred, due to electrostatics, from the photo drum on which the laser beam drew the image, onto paper. The toner is held onto the paper, preserving the image, only due to electrostatics. To fix the toner, the paper is rolled between rollers, one of which is a thermal oven heated to a temperature of 180-220°C. The toner melts and penetrates the paper texture. Once cooled, the toner hardens and adheres firmly to the paper. If the paper is heated again to 180-220°C, the toner will again become liquid. This property of toner is used to transfer images of current-carrying tracks onto a printed circuit board at home.
After the file with the printed circuit board design is ready, you need to print it using a laser printer onto paper. Please note that the image of the printed circuit board drawing for this technology must be viewed from the side where the parts are installed!
An inkjet printer is not suitable for these purposes, as it works on a different principle.
Preparing a paper template for transferring the design to the printed circuit board If you print a printed circuit board design on ordinary paper for office equipment, then due to its porous structure, the toner will penetrate deeply into the body of the paper and when the toner is transferred to the printed circuit board, most of it will remain in the paper. In addition, there will be difficulties in removing paper from the printed circuit board. You will have to soak it in water for a long time. Therefore, to prepare a photomask, you need paper that does not have a porous structure, for example photo paper, a substrate from self-adhesive films
I use old stock tracing paper as the paper for printing the PCB design. Tracing paper is very thin and it is impossible to print a template directly on it; it gets wrinkled in the printer. To solve this problem, before printing, you need to apply a drop of any glue to a piece of tracing paper of the required size in the corners and glue it to a sheet of A4 office paper.
This technique allows you to print a printed circuit board design even on the thinnest paper or film. In order for the toner thickness of the drawing to be maximum, before printing, you need to configure the “Printer Properties” by turning off the economical printing mode, and if this function is not available, then select the coarsest type of paper, for example cardboard or something similar. It’s quite possible that you won’t get a good print the first time, and you’ll have to experiment a little, choosing best mode laser printer printing. In the resulting print of the design, the tracks and contact pads of the printed circuit board must be dense without gaps or smudging, since retouching on this technological stage useless.
All that remains is to cut the tracing paper along the contour and the template for making the printed circuit board will be ready and you can proceed to the next step, transferring the image onto fiberglass laminate.
Transferring a design from paper to fiberglass
Transferring the printed circuit board design is the most critical step. The essence of the technology is simple: paper, with the side of the printed pattern of the tracks of the printed circuit board, is applied to the copper foil of fiberglass and pressed with great force. Next, this sandwich is heated to a temperature of 180-220°C and then cooled to room temperature. The paper is torn off, and the design remains on the printed circuit board.
Some craftsmen suggest transferring a design from paper to a printed circuit board using an electric iron. I tried this method, but the result was unstable. It is difficult to simultaneously heat the toner to desired temperature and uniform pressing of the paper to the entire surface of the printed circuit board when the toner hardens. As a result, the pattern is not completely transferred and gaps remain in the pattern of the printed circuit board tracks. Perhaps the iron was not heating up enough, although the regulator was set to maximum iron heating. I didn’t want to open the iron and reconfigure the thermostat. Therefore, I used another technology, less labor-intensive and providing one hundred percent results.
On a piece of foil fiberglass laminate cut to the size of the printed circuit board and degreased with acetone, I glued tracing paper with a pattern printed on it in the corners. On top of the tracing paper I placed, for more even pressure, heels of sheets of office paper. The resulting package was placed on a sheet of plywood and covered on top with a sheet of the same size. This entire sandwich was clamped with maximum force in clamps.
All that remains is to heat the prepared sandwich to a temperature of 200°C and cool. An electric oven with a temperature controller is ideal for heating. It is enough to place the created structure in a cabinet, wait for the set temperature to reach, and after half an hour remove the board to cool.
If you don’t have an electric oven, you can also use a gas oven by adjusting the temperature using the gas supply knob using the built-in thermometer. If there is no thermometer or it is faulty, then women can help; the position of the control knob at which pies are baked is suitable.
Since the ends of the plywood were warped, I clamped them with additional clamps just in case. To avoid this phenomenon, it is better to clamp the printed circuit board between metal sheets 5-6 mm thick. You can drill holes in their corners and clamp printed circuit boards, tighten the plates using screws and nuts. M10 will be enough.
After half an hour, the structure has cooled enough for the toner to harden, and the board can be removed. At the first glance at the removed printed circuit board, it becomes clear that the toner transferred from tracing paper to the board perfectly. The tracing paper fit tightly and evenly along the lines of the printed tracks, rings of contact pads and marking letters.
The tracing paper easily came off from almost all the traces of the printed circuit board; the remains of the tracing paper were removed using damp cloth. But still, there were gaps in several places on the printed tracks. This can happen as a result of uneven printing from the printer or remaining dirt or corrosion on the fiberglass foil. Gaps can be painted over with any waterproof paint, manicure polish, or retouched with a marker.
To check the suitability of a marker for retouching a printed circuit board, you need to draw lines on paper with it and moisten the paper with water. If the lines do not blur, then the retouching marker is suitable.
It is best to etch a printed circuit board at home in a solution of ferric chloride or hydrogen peroxide with citric acid. After etching, toner can be easily removed from the printed tracks with a swab soaked in acetone.
Then holes are drilled, conductive paths and contact pads are tinned, and radioelements are sealed.
This is the appearance of the printed circuit board with radio components installed on it. The result was a power supply and switching unit for electronic system, complementing an ordinary toilet with a bidet function.
PCB etching
To remove copper foil from unprotected areas of foiled fiberglass laminate when making printed circuit boards at home, radio amateurs usually use chemical method. The printed circuit board is placed in an etching solution and, due to a chemical reaction, the copper unprotected by the mask dissolves.
Recipes for pickling solutions
Depending on the availability of components, radio amateurs use one of the solutions given in the table below. Etching solutions are arranged in order of popularity of their use by radio amateurs at home.
| Name of solution | Compound | Quantity | Cooking technology | Advantages | Flaws |
|---|---|---|---|---|---|
| Hydrogen peroxide plus citric acid | Hydrogen peroxide (H 2 O 2) | 100 ml | Dissolve in 3% hydrogen peroxide solution citric acid and table salt | Availability of components, high etching speed, safety | Not stored |
| Citric acid (C 6 H 8 O 7) | 30 g | ||||
| Table salt (NaCl) | 5 g | ||||
| Aqueous solution of ferric chloride | Water (H2O) | 300 ml | Dissolve ferric chloride in warm water | Sufficient etching speed, reusable | Low availability of ferric chloride |
| Ferric chloride (FeCl 3) | 100 g | Hydrogen peroxide plus hydrochloric acid | Hydrogen peroxide (H 2 O 2) | 200 ml | Pour 10% hydrochloric acid into a 3% hydrogen peroxide solution. | High etching rate, reusable | Great care required |
| Hydrochloric acid (HCl) | 200 ml | ||||
| Aqueous solution of copper sulfate | Water (H2O) | 500 ml | IN hot water(50-80°C) dissolve table salt, and then copper sulfate | Component Availability | The toxicity of copper sulfate and slow etching, up to 4 hours |
| Copper sulfate(CuSO4) | 50 g | ||||
| Table salt (NaCl) | 100 g | ||||
Etch printed circuit boards in metal utensils not allowed. To do this, you need to use a container made of glass, ceramic or plastic. The used etching solution may be disposed of in the sewer system.
Etching solution of hydrogen peroxide and citric acid
A solution based on hydrogen peroxide with citric acid dissolved in it is the safest, most affordable and fastest working. Of all the solutions listed, this is the best by all criteria.
Hydrogen peroxide can be purchased at any pharmacy. Sold in the form of a liquid 3% solution or tablets called hydroperite. To obtain a liquid 3% solution of hydrogen peroxide from hydroperite, you need to dissolve 6 tablets weighing 1.5 grams in 100 ml of water.
Citric acid in the form of crystals is sold in any grocery store, packaged in bags weighing 30 or 50 grams. Table salt can be found in any home. 100 ml of etching solution is enough to remove 35 micron thick copper foil from a printed circuit board with an area of 100 cm 2. The spent solution is not stored and reuse is not subject to. By the way, citric acid can be replaced with acetic acid, but because of its pungent odor, you will have to etch the printed circuit board outdoors.
Ferric chloride pickling solution
The second most popular etching solution is an aqueous solution of ferric chloride. Previously, it was the most popular, since on any industrial enterprise ferric chloride was easy to obtain.
The etching solution is not demanding on temperature; it etches quickly enough, but the etching rate decreases as the ferric chloride in the solution is consumed.
Ferric chloride is very hygroscopic and therefore quickly absorbs water from the air. As a result, a yellow liquid appears at the bottom of the jar. This does not affect the quality of the component and such ferric chloride is suitable for preparing an etching solution.
If the used ferric chloride solution is stored in an airtight container, it can be reused many times. Subject to regeneration, just pour iron nails into the solution (they will immediately be covered with a loose layer of copper). If it gets on any surface, it leaves a difficult-to-remove yellow spots. Currently, ferric chloride solution is used less frequently for the manufacture of printed circuit boards due to its high cost.
Etching solution based on hydrogen peroxide and hydrochloric acid
Excellent etching solution, provides high speed etching. Hydrochloric acid, with vigorous stirring, is poured into a 3% aqueous solution of hydrogen peroxide in a thin stream. It is unacceptable to pour hydrogen peroxide into acid! But due to the presence of hydrochloric acid in the etching solution, great care must be taken when etching the board, since the solution corrodes the skin of the hands and spoils everything it comes into contact with. For this reason, it is not recommended to use an etching solution with hydrochloric acid at home.
Etching solution based on copper sulfate
The method of manufacturing printed circuit boards using copper sulfate is usually used if it is impossible to produce an etching solution based on other components due to their inaccessibility. Copper sulfate is a pesticide and is widely used for pest control in agriculture. In addition, the etching time of the printed circuit board is up to 4 hours, and it is necessary to maintain the solution temperature at 50-80°C and ensure a constant change of the solution at the surface being etched.
PCB etching technology
For etching a board in any of the above etching solutions, glass, ceramic or plastic dishes, for example from dairy products. If you don’t have a suitable size container at hand, you can take any box of thick paper or cardboard of a suitable size and line its inside plastic film. An etching solution is poured into the container and a printed circuit board is carefully placed on its surface, pattern down. Due to the forces of surface tension of the liquid and its light weight, the board will float.
For convenience, a plug can be glued to the center of the board using instant glue. plastic bottle. The cork will simultaneously serve as a handle and a float. But there is a danger that air bubbles will form on the board and the copper will not be etched in these places.
To ensure uniform etching of copper, you can place the printed circuit board on the bottom of the container with the pattern facing up and periodically shake the tray with your hand. After some time, depending on the etching solution, areas without copper will begin to appear, and then the copper will completely dissolve on the entire surface of the printed circuit board.
After the copper is completely dissolved in the etching solution, the printed circuit board is removed from the bath and thoroughly washed under running water. running water. Toner is removed from the tracks with a rag soaked in acetone, and paint is easily removed with a rag soaked in a solvent that was added to the paint to obtain the desired consistency.
Preparing the printed circuit board for installation of radio components
The next step is to prepare the printed circuit board for the installation of radio elements. After removing the paint from the board, the tracks need to be sanded in a circular motion with fine sandpaper. There is no need to get carried away, because the copper tracks are thin and can be easily ground off. Just a few passes with abrasive with light pressure are enough.
Next, the current-carrying paths and contact pads of the printed circuit board are coated with alcohol-rosin flux and tinned with soft solder using an electric soldering iron. To prevent the holes on the printed circuit board from being covered with solder, you need to take a little bit of it onto the soldering iron tip.
After completing the manufacture of the printed circuit board, all that remains is to insert the radio components into the designated positions and solder their leads to the pads. Before soldering, the legs of the parts must be moistened with alcohol-rosin flux. If the legs of the radio components are long, then before soldering they need to be cut with side cutters to a protrusion length above the surface of the printed circuit board of 1-1.5 mm. After completing the installation of parts, you need to remove any remaining rosin using any solvent - alcohol, white alcohol or acetone. They all successfully dissolve rosin.
It took no more than five hours to implement this simple capacitive relay circuit from laying out the tracks for manufacturing a printed circuit board to creating a working sample, much less than it took to type up this page.
Out of curiosity, I bought a marker for printed circuit boards – edding 791 paint (bought at IEC for 95 rubles). They write on the Internet that it is varnished.
The marker had a tamper-evident sticker on it. To use it, you need to shake it and press the tip in a vertical position so that the ink gets onto it and saturates it.
I prepared the board, punched and drilled holes. Let's start drawing the drawing. I bought a marker with a line thickness of 1-2 mm, such a marker minor work It’s impossible to do, the resulting lines are 1.5-2 mm thick. If the tracks are connected, then just wait for the ink to dry and remove the excess marker with a needle. The paths around the holes are made by briefly touching the hole with a marker; the ink from the marker spreads a little in all directions, forming a good area.
Before etching
After etching
After removing the ink.
The ink can be easily removed with alcohol or sandpaper. There are almost no etch marks under the marker; perhaps the board was overexposed.
This marker is well suited for applying, not small, designs on a printed circuit board.
We all love to assemble circuits, but not everyone wants and knows how to lay out printed circuit boards. Most often we look for a ready-made signet on the Internet and in most cases we find it. It would seem, go ahead, poison and solder! But not everything is so rosy, because often these found signets look like this:
Not a single signed item. A complete rebus, a riddle! And, it seems, turn on the “mosch” and fill in the elements, because the diagram is at hand. But the program was created to make our lives easier, and not vice versa.
Therefore, I will briefly, from the beginning, tell you how to approach the board layout in Sprint-Layout, so that you don’t have to guess later what kind of detail I put in here. Let's do the right thing right away!
You can’t cover everything in one short article; I’ll go over some of the main points. So let's create new project, set the name of the board and the expected size (it can be easily adjusted later).
Be sure to select a suitable working mesh.
For small projects With large elements a 1.27 mm mesh is suitable, for more advanced and dense ones 0.635 mm and so on. Elements and tracks will be placed with reference to the nodes of this grid. You can make a mesh for Soviet parts: 2.5 mm or 1 mm.
Be sure to understand the layer system in the program, understand how everything works, and use the photo view.
Make inscriptions on layers for inscriptions, and make paths and polygons on layers for copper, etc.
The archive contains help programs in Russian.
Let's start adding details to the board. At this stage, you should not confuse the values of “Type” and “Denomination”; later I will tell you why.
Enter the values, adjust the font size to taste, and click OK.
We see an element with markings. Now we can distribute and “compact” our markings.
Select the denomination and drag it with the mouse to the desired place. Before this, you need to reduce the grid size to an acceptable level.
Now, that's better.
Now we move the element symbol closer. If necessary, you can rotate it by selecting it first.
Next, so as not to suffer so much with each element, we simply copy it and change the data in the element’s properties.
Our board is already quite ready for manufacturing, but why do we need to overload the solution with excess copper?
No need! We will minimize the area of copper being etched. To do this, select all the elements on the board and click the “Metalization” button at the bottom of the program window and change the value to an acceptable one, for example 0.5 mm.
Everything is fine, but some legs can and sometimes even need to be placed on a metallized area. There's nothing complicated.
Select the required legs and change the metallization offset value to 0. That's it, now the leg is on the earth bus.
What if you need a thermal barrier to facilitate soldering on large sites? Select drawing paths and draw a thermal barrier.
This is the simplest and most obvious way. But you can also take advantage of the program’s built-in capabilities for creating thermal barriers. Select the desired pad and explore the menu on the right.
Check the "Thermal barrier" checkbox and configure the direction and width of the barrier's "bridges". It is very convenient because you can configure many sites at once. The thermal barrier function only works when the automatic landfill is turned on. Not supported by all versions of Sprint-Layout. Use fresh.
Everything is drawn, we can admire the result by clicking the “photo view” button.
A nuance - you can edit the size of the element labels individually; to do this, select the “victim” and click the properties button on the right. The settings are quite extensive. However, it is better to install all the inscriptions in the same style.
The turn of “cosmetics” has come. So that all the drawings of elements on the board have a uniform appearance and line thickness, do the following:
1. select the layer with element labeling;
2. turn off the tracks layer;
3. select all (ctrl+A);
4. adjust the thickness of the lines of all elements at the same time;
5. Activate the tracks layer again.
Beauty! By the way, don’t forget to adjust the colors of the layers in the program to suit everyone’s taste, for those who found my palette a bit gloomy.
Now let’s remember the beginning of the article and find out why you shouldn’t enter the value of an element in the field for its type. It’s simple, it turns out that when we added elements, we already generated a list of elements!
Of course, a more correct practice is the primacy of the diagram in the project, then creating a list of elements is the job of the program for drawing diagrams. In the ABACOM software package it is sPLAN.
Editor's note
All that remains is to purchase according to the list and end up with a beautiful payment self-made. And people are not ashamed to show such a drawing on the forum, and there will be no unnecessary questions about the board.
Files
And here is a Russian help on Sprint-Layout and an excellent free book by our comrade Mikhail Tsarev (Tsoy73):▼ 🕗 12/27/16 ⚖️ 2.14 Mb ⇣ 170
A PCB marker is a marker with which we can draw printed circuit traces.
Such markers can have different line thicknesses. Below in the photo is my 0.8 mm thick marker.
This marker leaves a very juicy and even mark on foil PCB
PCB marker at work
In order for the printed tracks to turn out very smooth and beautiful, we must sand the textolite with sandpaper of the finest abrasive. In everyday language, such paper is called micron paper; in extreme cases, it can also be called zero paper (slightly larger abrasive).
We take our hero in hand and write something like that. I wrote the name of our site: “Practical Electronics”.
We will etch our scarf with “Practical Electronics” in a solution of ferric chloride. For this we need plastic bath(under no circumstances use metal trays, otherwise ferric chloride will corrode them) and the ferric chloride powder itself. Pebbles can also be used, but you need to grind them well and dissolve them.
Let's pour clean water into the bath so that the scarf is completely hidden there and pour iron chloride powder into it, not forgetting to stir. We also use non-metallic objects for this. IN in this case wooden spatula.
How much iron chloride should be added to water? There is no need to remember any ratios of water to iron chloride. The rule is simple: than stronger solution, the faster the scarf will be etched, and vice versa. If you have nowhere to rush, then, of course, it is better to wait another hour in order to save money. The solution should look dark brown, and if you often etch scarves, you will be able to determine by eye exactly how much powder to pour.
My solution was not very strong. We release our scarf there using plastic tweezers and wait.
The etching process is a common chemical reaction. If you remember from your chemistry course, in order for the reaction to proceed faster, you can increase the temperature, increase the concentration of the solution, and even purely mechanically - interfere with this chemical reaction something :-). Since I didn’t pour enough, all that remains for me is to pour warm water And mechanical impact. To do this, I “drove a wave” in the bath.
From time to time we check our scarf. In! The etching process is in full swing! Just a little more and you can remove the scarf from the bath.
An hour and a penny later, our scarf was etched. Wash off the remaining solution with water. And here is the finished scarf with the inscription!
In order to remove the green trace of the marker, we use acetone and a cotton swab dipped in acetone.
For the sake of beauty, we’ll tinker with this whole thing. To tin, you must first rosin
and now to tin
We wash off the remaining rosin using acetone or other powerful solvents, such as Flux Off. And... voila!
Conclusion
The letters (let them be the tracks of the printed circuit board for us) turned out exactly the same width. If you draw lines using a ruler, then, I think, you can achieve factory quality :-) The Edding brand marker coped with this task perfectly. But, since the marker is Japanese and of very high quality, the price, of course, is a little bit high, just like for Japanese cars. At the time of writing this article, the price of such a marker in stores retail was 150 rubles, which, of course, is more expensive than simple ordinary markers. But I can say one thing: such a marker will last you a very long time, if you don’t forget to cover it with a cap and don’t color in children’s coloring books.
Ali has it too big choice markers for printed circuit boards: