Car alarm starline a 93 operating instructions. Car alarm StarLine A93: owner reviews, instructions for use and characteristics. Car alarm StarLine A93 CAN LIN with auto start: reviews
Starline A93 contact layout
All connectors with purposes are located on one side. This greatly simplifies electrical installation.
The location and purpose of the contacts (pinout) of the main connectors are given below
Connecting main circuits
Electrical wiring must be carried out with the connectors disconnected. It starts by connecting the negative wires (grounding). To do this, you need to find standard ground for the bolts. It is usually located under the floor mats in the front corner of the car floor. If standard grounding bolts cannot be found, you can install the grounding under a good self-tapping screw, having first cleaned the metal installation site.
It is better to connect to the positive power bus directly from the battery through an additional fuse. It is better to use a wire with a cross-section of at least 6 square millimeters, stranded copper in polyvinyl chloride (PVC) insulation. Connections are made using the “twisting + soldering” method with heat shrink insulation.
Connection to CAN buses (LIN)
Connection to CAN and LIN buses is carried out according to the diagram
If the CAN bus does not support central locking, the following diagram should be used
The low current control installation diagram is shown below
Power control switching diagram
The StarLine A93 system has an engine blocking circuit in case of unauthorized start
Usually the supply voltage supplied to the fuel pump, injectors, and ignition coil is blocked. The trouble is that all car thieves know about this and easily bypass them. Therefore, Starline A93 has low-current blocking channels. They can be connected, for example, to a crankshaft sensor, without which the engine will not start. Then the car thieves will definitely have to tinker, and most likely leave the car alone.
Connecting the immobilizer crawler and GSM module
Autostart mode (for warming up the engine, from the apartment) is provided by the VR-03 lineman. The diagram is shown below
The GSV module is sometimes not included in the package and must be purchased separately
The GSM module board looks like:
It is installed directly on the car alarm board. To do this, you must first disassemble it.
General signaling scheme
General diagram of plug-in modules and nodes
Setting up the Starline A93 alarm system
After execution electrical installation work check the reliability of the connections, the absence of breaks and short circuits, connect the central and other units. Now you can connect the power terminals to battery. At this moment, the alarm control key fobs with the batteries turned on should be at hand. The alarm can immediately go off (and probably will). Then try turning it off. If it doesn’t work right away, turn off the siren while setting up the functions so as not to scare the dogs away.
If everything works right away, look for a fault (electricians joke). Try a test run. If possible, sniff for any foreign wiring odors.
Next, turn off the engine and check the car for errors. After this, they begin programming the car alarm functions using the tables attached to the installation and operating instructions. More on this in the next article.
Automotive security alarms Starline and their modifications occupy a leading position in the car alarm market and are popular among car enthusiasts, as evidenced by numerous positive reviews from owners. Particularly interesting car alarm Star Line I model A93. The instructions for the Starline A93 alarm with auto start will be discussed below.
Car alarm instructions
The Starline car alarm, and especially its Starline A93 model, has proven itself in our automobile market positive side thanks to the relatively cheap cost, as well as a large set useful functions And technical capabilities to protect the signal from various reading devices (code grabbers). It has a rich set of equipment that allows you to install many additional automotive functions. The alarm system also has similar functions.
Its peculiarity is not only the presence of an autostart function for the power unit, operating in temperature conditions(periodic warming up of the engine in winter time) and by timer (start at a certain time). Among other things, this GSM alarm. With its help, you can track a car using a special GSM signal. Also, the developers of this security system created an auto-start system that works according to ECO standards.
It should also be noted that this car alarm can be installed both on expensive car brands and on used domestic cars, and the security qualities will not be affected in any way.
The A93 operating instructions are divided into two parts:
- description of operating procedure, where indicated general functions and parameters of this security system;
- description of installation of individual functions, which contains a detailed connection diagram.
Now let's look at each section separately.
User manual
Instructions for use include the following sections.
It is important to remember that this part of the user manual does not contain recommendations for installing an alarm system, so the car enthusiast can set up all functions independently if he carefully reads the instructions.
Installation instructions
This part of the user manual also contains a lot useful information, and first of all, it describes the installation procedure for this security system, and also indicates the recommended zones for installing all sensors and the unit that are included in the kit.
It consists of the following sections:
- approximate installation locations of alarm elements(installation map), here the manufacturer gives detailed recommendations where to install this or that unit so that the car is completely protected, and additional functions could effectively start the engine automatically;
- connection procedure, there are detailed diagrams according to which the car enthusiast (if he decides to carry out the installation himself) is obliged to connect all the elements together after their installation, for example, the engine start sensor;
- programming order, here it is indicated how to program the security system, set a personal PIN code, and program the interface.
The Starline A93 alarm system is a multifunctional security system that provides reliable protection any car from illegal attacks. Despite the fact that many drivers compare how much this model costs compared to other alarms and make a choice not in favor of it, they are mistaken, since its functionality is greater than that of others security systems similar class.
1. To access the ignition switch connector, remove bottom part steering shaft casing. To do this, you need to remove the plastic trim under the steering column, releasing the clamps, then remove the lower part of the casing (fastened with three self-tapping screws and two screws).
Steering shaft housing. General form
Plastic lining fasteners
Plastic cover removed
Self-tapping screws and screws for securing the steering shaft housing
The lower part of the steering shaft housing has been removed
2. To access the VSM unit, remove the left side trim of the central tunnel (fastened with one screw). Then remove the VSM unit (mounted with a bolt and nut).
Self-tapping screw for fastening the side trim
Side trim removed
Bolt and nut for fastening the VSM unit
VSM block removed
3. Install the antenna module with built-in shock and tilt sensor on the windshield, LED on the left pillar. Install the service button covertly in any convenient place.
Possible location for installing the antenna module
LED installation location
4. Install the siren under the hood (attach it to the nut) and the engine temperature sensor (using plastic ties). Route the wires into the passenger compartment through the standard seal on the left side of the engine shield.
Possible siren installation location
Siren installed
Engine temperature sensor installation location
The temperature sensor is fixed to the pipe using ties
Standard seal. View from the salon
5. Secure the StarLine A93 central car alarm unit to the right above the BCM unit.
An example of the location of the central car alarm unit
6. Connect the StarLine alarm ground at the bottom left under the VCM unit under the standard nut.
Connection masses
7. Connect the CAN bus and LIN bus StarLine in the harness of connector 3 of the BCM unit.
Conventional numbering of connectors on the VSM unit
CAN bus(yellow-red, pin 16 and gray, pin 15)
LIN bus(blue-white, pin 8)
LIN bus connection
8. Connect the trunk limit switch in the harness of connector 3 of the BCM unit.
Trunk limit switch(yellow, pin 14)
Connect the hood end switch in the harness of connector 2 of the BCM unit.
Hood switch(white-black, pin 15)
Connecting the hood and trunk limit switch
9. In the harness of connector 2 on the BCM block, connect an alternative control of light signals (black and white wire of connector X3 Alarm Starline).
Light control(red, pin 5)
10. To bypass the standard immobilizer, remove the battery from the key and place the key in the bypass module immobilizer StarLine BP-03. Then connect the bypass module to any wire of the standard antenna on the ignition switch.
Standard antenna wires (green and white)
11. In the ignition switch connector harness, connect the engine starting power circuits, power security complex and power autostart module.
Ignition(blue-black)
Starter(red)
Power + 12V(brown)
12. Program the security and service functions of Starline A93 (see installation instructions, section “Main menu for programming car alarm functions”, Table 1).
13. Program the vehicle starting parameters (see installation instructions, section “Main menu for programming car alarm functions”, table 2).
14. Adjust the sensitivity of the shock and tilt sensor (see the installation instructions, section “Connecting the transceiver (antenna module) and setting the shock and tilt sensor”). Factory sensitivity values: warning level of the shock sensor - 10, alarm level of the shock sensor - 5, tilt and movement sensor - 5. After setting, check the operation of the sensors, if necessary, repeat the setting procedure.
15. Check the operation of the Starline A93 car alarm. Reassemble the interior in the reverse order.
Based on materials from the site install.starline.ru
StarLine a93 is a modern, new generation car alarm system that keeps your car safe for high level. The Starline A93 alarm system with auto start allows you to control the car remotely, which is very convenient. For example, in winter, you can turn on the interior heating in your car or start the engine to warm up without leaving your home. In summer you can also control the air conditioner remotely. The operating instructions for the key fob will show all the possibilities and tell you how to use the alarm correctly.
On this page of the site you can download the manual operation of StarLine a93 Can Lin. The manufacturer of Starline a93 GSM strongly recommends reading the user manual before use. Thanks to this, setting up the key fob will be easier, and you will be able to familiarize yourself with all functionality devices.
A brief guide to using StarLine a93 ECO will help you set up the key fob step by step, get acquainted with the principle of its operation, and familiarize yourself with information on programming the device.
Proper use – maximum effect
The installation instructions are also available online, allowing you to read them without downloading. The instructions are what you need to read first. There are several reasons for this:
- After reading the user manual, you will not break the key fob trying to learn how it works on your own;
- You will learn the full functionality of StarLine a93;
- You will be able to competently use all the capabilities of the device;
The operating instructions are available for download and online viewing on our website completely free of charge. After reading the manual, you will learn how to configure options individually, be able to use car autostart, and learn how to receive car safety notifications on mobile phone and open up many more possibilities.