Do-it-yourself automatic soldering iron stand. Multifunctional Soldering Stand

Main tool home radio amateur - soldering iron. Unlike other devices, it cannot simply be placed on a table (workbench) while working. Why? Right! He is hot. Therefore, you will need a special stand.

There are a lot of different devices on sale, from a simple holder to a whole complex called a soldering station.

In most cases, a soldering iron is needed to perform urgent tasks. repair work. If you are not a professional “homemade” tool, the instrument usually gathers dust in a box on the balcony, appearing once or twice a year. In such cases, many people use the first object they come across as a stand.

However, if you put in just a little effort, a DIY soldering iron stand will look no worse than a factory one. Especially if you regularly make electrical circuits.

Minimum required for stand

1. Stable base. Made from a material that conducts heat poorly or equipped with legs
2. Soldering iron supports
3. Container for rosin (flux).

Additional options"

1. Tinning area
2. Solder container
3. Tip cleaning device
4. power regulator (can be of two types: smooth adjustment, or stepwise limitation for the time of a break in work).

Leafing through old magazines

In old Radio magazines you can find drawings on how to make a stand with an economical load switch.

• As a basis ( 1 ) a board with a selected middle is used, or a U-shaped structure made of a strip of plywood and two bars along the long edges
• Under the surface there is a 220 volt relay contact group ( 2,4,5 ) with large current collecting areas. The connection circuit transfers power either directly or through a diode. The radio element “cuts off” the halves of the half-cycle of an alternating voltage of 220 volts, reducing it to a value of 110
• Through traction ( 6 ), spring loaded ( 7 ) button ( 8 ) presses the contacts when the soldering iron is lying on the stand. Electricity consumption is half as much, while the soldering iron almost instantly heats up to full power. The rod is attached to the console ( 9 )
• The tool itself is located on brackets ( 3 ) And ( 10 )
• At the rear there is a soldering iron socket connected to the relay output contacts. Connected to the input power wire nutrition
• Between the posts, usually nailed tin can from shoe polish or Vaseline, for storing rosin

The design is simple, but convenient and effective. If you don’t want any hassles with contacts, we’ll make a simple, functional stand. Again from the experience of Soviet radio amateurs.

A do-it-yourself soldering iron stand is a very convenient and practical device, which is a kind of table and performs protective function. Before soldering, the soldering iron must be warmed up. When warming up, the case gets very hot, which is why you should use a stand to protect any items.

Design of the soldering iron stand: 1 – base, 2, 4, 5 – contacts from relay type MKU-48 for 220 V, 3.10 – support posts, 6 – disk, 7 – spring, 8, movable contact rod Kp 9 – square, D1 – D7Zh type diode.

The need for a soldering iron stand

A high-quality and practical stand for a soldering iron is needed by all those who deal with soldering. You can make it yourself from scrap materials, you just need to have certain skills and certain tools. A homemade soldering iron stand is quite simple to make and use. In order for a thing to be convenient, it must have certain slots intended for containers with flux and alcohol, boxes for rosin and alcohol, as well as a place for displaying some parts. A homemade soldering iron stand can be used with a tool of any power. When making a structure, it is necessary to arrange all containers in such a way that it is convenient to solder.

Good day to all.

Today I want to tell you about a universal soldering iron stand that I purchased on eBay.

It’s not that I’m an ardent fan of assembling or soldering anything, but sometimes it happens that you can’t do without a soldering iron. Either the wiring needs to be soldered somewhere, or the button needs to be re-soldered, or something else will come off or break suddenly and at the very inopportune moment. Since I got a soldering iron, all these problems have become easily solvable and not as global as they were before. But there was still one nuance - sometimes you had to solder something extremely inconvenient, when you hold the wires with one hand and try to solder them with the other. In such cases, taking solder becomes very problematic and then I had to resort to the help of my wife :) Use it instead of a wire clamp. My wife didn’t really like this job and I once thought about purchasing something more trouble-free than a woman. In other words, I started looking for a stand. Much to my surprise, problems with searching of this device I didn’t have any problems, but there’s a problem with variety - I managed to find only a few models that didn’t differ much from each other in their functionality. In the end, I decided not to overpay and purchased one of the cheapest lots - a stand that cost only $9.19. Perhaps some of you will say that you can buy this in some hypermarket or radio equipment store, but let’s not forget that this review was written by a resident of Belarus, and we have a completely different situation here. And rather than wandering around the shops, it’s easier for me to place an order online and receive it in the mail after a couple of weeks.

The seller turned out to be quite prompt and sent my parcel a few hours after payment. If anyone is interested, you can see the movement of a parcel from China to Belarus.

During the not very long journey, the parcel suffered a lot: one side of it was terribly jammed.


But there were no losses and the contents of the parcel were not damaged. I really can’t imagine how this is possible, taking into account such damage to the packaging :) As you can see, the factory packaging was once a beautiful colorful cardboard box with fairly high quality printing. Our stand is depicted on the front side of the box, and its main characteristics and capabilities are on the sides.


Inside the box was our stand, as well as a black and white instruction manual. The stand is supplied disassembled, the grips come in a separate cardboard box, and the soldering iron holder, made in the form of a spiral, also comes separately.


There are no complaints about the quality of production. Immediately upon receipt, the plastic emitted a not very strong, but not very pleasant smell. Today it has decreased significantly, but the stand still smells, although this is not critical, since much stronger odors appear during soldering :)

There are 2 fastenings on the stand - a movable hinged one for the grips and a stationary one for the holder.


They are fixed using special clamping screws with plastic caps. It seems that they are not very flimsy, but this saving did not seem very practical to me. If you try to tighten the fastener, you may not calculate the force applied and break the plastic. It would be much better if these screws were completely metal.

The holder has a knurled end that allows it to be securely secured using a clamping screw.


But the fastening of the grips is simply pressed against the stand, which is also not very good. It is not possible to securely fix it, one way or another it remains movable: (Most likely you will have to drill small holes for the clamping screw with reverse side holders, or use electrical tape :) By the way, the entire part of the structure on which the clamps are installed is connected using hinge joints. Thanks to this, you can easily position the paws as you please. There are 3 such connections in total, that is, this structure can be bent in 6 places almost 360 degrees. There are no problems with the choice of positions here and cannot be. The grips here are a la crocodiles, with a fairly tight spring, so you have to be careful when fixing fragile objects. But everything is clamped securely - nothing will accidentally fall out.


The wings are clamped with decent effort. You may need pliers for fixation :)


And above the whole thing rises a plastic magnifying glass, fixed on a bendable support. If you believe the seller and what is written in his ad, it magnifies it 3.5 times, and if you use the small insert located at the top of the magnifying glass, then 12 times.


I don’t know about the accuracy of this data, but the fact that glass magnifies is a fact.

Right there, near the magnifying glass, you can see a button that turns on the backlight. Yes, yes, this stand has LED lighting, which can be useful in some cases. The button presses well and smoothly. No problems with its operation have yet been discovered.


It includes 2 diodes located under a magnifying glass. It’s not that these diodes give light like a normal lamp, but illuminate some kind of small area or their power is quite enough to disperse the shadow.


This whole cunning circuit is powered by 3 AAA batteries, which are installed at the foot of the stand.


When assembled, this entire structure looks like this:


And finally, about the shortcomings. Or rather, not so much about the shortcomings, but about what I would like to see here. And I would like to see a built-in socket and cord here to connect the stand to the network. I think it would be convenient to plug the soldering iron into the stand, rather than into a socket - there would be more room for maneuver, so to speak. Perhaps, if I’m not too lazy, I’ll try to modify the stand myself :)

Overall, I was very pleased with this purchase. The stand turned out to be very convenient, practical and functional. It fully justifies its cost and will definitely be useful to everyone who has ever held a soldering iron in their hands. The only 2 nuances that can be a little frustrating are the plastic lens, which will probably get scratched over time and the “lambs” are not very comfortable to clamp (but this is only if you want to clamp them very tightly).

And this is what she looks like fully armed:


Basically, that's all. Thank you all for your attention and time spent.

I'm planning to buy +46 Add to favorites I liked the review +35 +65

When working with a soldering iron, a special stand is required. The soldering iron cannot simply be left on the table or some other surface. As a rule, any suitable item in the house is used in this capacity. With a little effort, you can make a soldering iron stand yourself. Such a device will be cheaper and will be adapted to the needs of the master.

How to make a soldering iron stand with your own hands? To make it, you first need to make a stable base from a material that conducts heat poorly. The following tools and materials are required for work:

A rectangular blank is cut from a sheet of chipboard, sandpaper sand the sides, rounding the corners. Next, make four rubber legs, which can be cut from a piece of rubber or a cork from chemical test tubes. The legs are screwed to the base using self-tapping screws.

A hook is bent from a long strip of iron with pliers, which is used to install the heating part of the soldering iron. At one edge of the stand, an iron strip with a hook is secured with bolts. To reliably fix the structural elements, you need to pre-drill holes in the chipboard workpiece.

The holder for the soldering iron handle can be made from any part with a suitable recess . It is bolted to the edge of the music stand. Closer to heating element install the soldering holder in the same way. For this they use metal plate from old radio components or other consumables.

At the soldering site, you can melt a piece of tin, which is heated during operation. This results in a convenient and versatile device. Rubber feet give the structure stability and prevent damage to the table surface.

The simplest device can be made from thick wire. It is a cone spring that is attached to a stable base. A piece of wire, approximately 30 cm long, is wound onto the tool. There is an eyelet at the end for attaching to the stand. For the spring, you can use a thin clothes hanger.

The base is assembled from any suitable item - a tin can, unnecessary detail from household appliances or a piece of plywood, etc. A hole is first drilled in the workpiece, where a spring is attached using a bolt.

In another version of the design, rectangular holders with recesses for a soldering iron are made from wire using pliers. They are fixed on both sides to a base made of chipboard or wooden block. The soldering installation can be equipped with containers for tin or rosin, and a box for storing small parts, which is glued with special glue.

Soldering iron stand with magnifying glass. To make it more convenient to work with small parts, a special stand with a flexible holder (“third hand”) is installed on the stand. With its help you can fix various equipment: a magnifying glass, a backlight and other tools. The holder is secured with hinges, which allows you to rotate the device in different directions. All holder parts are made from metal elements to ensure the stability of the structure.

To work, you will need a computer power supply cover and the following tools:

• metal scissors;
• ruler or caliper;
• file or sandpaper;
• marker.

Mark with a marker approximate dimensions blanks for parts from a computer (width 60 mm, height 35 mm). A stand is cut out according to the marks made, then recesses are made on the sides where the tool is installed. For safe work The sharp edges of the product are treated with a file or sandpaper. Thus, a homemade stand for a soldering iron can be made in 15 minutes.

A computer's power supply can become a mobile device. Such a device is a box or case, inside of which there are compartments for soldering, rosin, a clamp for circuits and other small parts. The wire holder is attached to the outside and easily folds over the lid of the pencil case.

The product is easy to manufacture and does not require special materials. For holders, fuse jaws are used, which are attached to a base made of a wooden block or PCB. The distance between the holders is set in accordance with the size of the soldering tool. The fuses are screwed using self-tapping screws into pre-drilled holes.

If you urgently need a soldering iron, you can quickly make a stand from screws or nails. IN wooden base nails are driven in crosswise. This design is quite stable and holds the tool well.

To make a homemade soldering iron stand, you do not need any special knowledge or skills. For work, scrap materials that can be found in any home are often used. DIY devices are simple and easy to use.

Basic and auxiliary options of the soldering iron stand

To make the device, you need to use materials that do not heat up very much and practically do not conduct heat. Good Alternative option- this is equipment homemade stand special legs. The minimum functionality of the design is:

• convenient support for the device heated during operation;
• the presence of a container for flux, ensuring the comfort of using the soldering iron.

In addition, you can add a row yourself additional functions, which include:

1. Equipping the stand with a platform for tinning.
2. Adjusting the power of the device. It can be performed either smoothly using a thermostat, or in stages.
3. Installation simple device to remove solder residue from the tip.
4. Additional capacity for solder.

How to make a soldering iron stand with your own hands? Below we present some of the most simple ways, from which you can choose the most suitable one for you.

Stand with “third hand” device

This design allows you to work with the soldering iron as comfortably as possible, without wasting effort on holding the soldering iron and the two parts being connected at the same time. It is quite deservedly called the “third hand”. To make it you will need the following available materials and accessories:

• two glasses from decorative candles;
• leg from old table lamp or a small lamp;
• two alligator clips;
• a magnifying glass that will make it much more convenient to work with small details;
• a spring retainer, which you can make yourself from ordinary steel wire;
• wooden base.

The first step is to prepare the basis for the future stand. To do this, we mill three niches in it. The first two will be
be used for installing candle cups, and the third is for a cleaning cloth that removes solder from the soldering iron. After this, all work is performed in the following sequence:

1. We mount the cups in the prepared niches.
2. We mount alligator clips onto the flexible lamp rod. It is better to make the distance between them adjustable.
3. We install the spiral soldering iron holder in one of the corners of the base.
4. We drill holes and screw the rod with clamps to the wooden stand.
5. If desired, you can attach a magnifying glass to the top of the “third hand”. Also very often it is made removable or installed on a separate rod.

This stand does not require significant financial investments, however, it makes working with a soldering iron easier.

Stand with power regulator

In Chinese online stores you can already order ready-made kits for home soldering stations, which are quickly assembled into a system for adjusting and monitoring the power of the tool. You can also make a regulator yourself, using components such as:

• a constant resistor with a nominal value of 4.7 Ohms (in the diagram - R2);
• a variable resistor, through which the power will be adjusted (up to 500 Ohms, R1);
• 0.1 microfarad capacitor (C1);
• dinistor DB3 (VD3);
• triac BTA06-600 (VD4);
• diode 1N4148 (VD1);
• LED that will light up when power is turned on (VD2).

How to make a soldering iron power regulator out of all this? The answer to this question can be found in the diagram below.

You can make the board yourself. Holes for parts are drilled in it and conductive paths are made.

If you have minimal experience working with printed circuit boards, making the regulator will not be difficult. You can install it directly on the soldering iron stand. If you plan to use the device at a power above 100 W, you will need to use an aluminum radiator, which will remove excess heat from the triac.

A soldering iron with a power regulator will allow you to work with small parts and LEDs, and will provide the ability to customize the device to suit your needs. In addition, it will help reduce the load on the device and extend its service life.

The stand itself in this case can be made from rectangular cuttings of boards or chipboard. Using self-tapping screws, a steel plate is screwed onto it, curved in the form of an inverted letter “P” with cutouts for installing a soldering iron. Additionally, you can install containers for rosin and solder (the same cups from decorative candles).