Methods for repairing a sliding wardrobe, detailed instructions. Adjusting sliding wardrobe doors Adjusting sliding wardrobe door wheels

During the operation of cabinet furniture, it may be necessary to adjust the sliding wardrobe doors, for example, when problems with closing them arise as a result of misalignment. In this case, it is not necessary to call a specialist, since you can almost always adjust the doors yourself.

Here are the most common faults:

• doors not closing tightly;
• when closing, the door warps;
• the door came off the track.

For each of the listed cases, appropriate instructions for solving these problems will be given below.

Fixing loose closure

If there is a loose connection to the cabinet wall of one of the doors, or it opens spontaneously, the stopper is to blame. It is a small curved plate made of steel. The design of sliding wardrobe doors is such that a stopper installed in the groove of the guide provides reliable fixation.

In our case, the lack of door fixation in closed position indicates that the stopper needs to be adjusted. After this is done, we recommend gluing it to the guide using superglue for this purpose.

If the stopper is not found, do not worry, you can always buy it at any store that sells accessories for cabinet furniture. To install, you will need to remove the doors and dismantle the bottom guide, since the stopper must be installed through its end.

Elimination of door distortion

During the operation of cabinet furniture, the door may become skewed. This malfunction violates the aesthetics appearance cabinet, since when closed the doors do not fit tightly against the side walls. As a result, a gap is formed at the top or bottom.

It is not difficult to fix such a malfunction. To adjust the door vertically aluminum profile at the end (usually at the bottom) there are two holes in which hex screws are located. In most cases, they are covered with baffle tape. By rotating the lower screw, the door slope is adjusted.

This is done with a hex screwdriver or a furniture wrench. If there is a gap, the screw must be rotated clockwise from below. Rotation should continue until the edges of the door are aligned with the side walls. Accordingly, if the gap is at the top, rotation must be done counterclockwise.

There are screws for adjustment on each door on the left and right; using them you can also adjust the gap that occurs between the rails and the door.

Fixing a problem where doors are off track

If you open (close) the doors installed on the wardrobe carelessly, then sooner or later they may come off the rail (lower guide). It is advisable to prevent such a situation, but if it does happen, it is not difficult to eliminate it. All that is required is to carefully lift the door and place it back on the guide rail. Particular care must be taken when lifting mirror doors so as not to damage them or injure yourself.

Problems with derailment can be avoided if you do not apply excessive force to the doors when opening or closing the wardrobe. It is much easier to fix something that interferes with normal closing than to subsequently deal with repairs and adjustments.

As you can see, adjusting wardrobe doors can be done independently; in most cases, this does not require special tools or skills.

Many people have encountered situations where wardrobe doors no longer close tightly and look warped. To avoid deformation of the door closing system, you will need to eliminate all problems. Many people are looking for information and want to know how to adjust wardrobe doors; to do this, you can contact a specialist or fix the defect yourself at home.

To adjust wardrobe doors, you may need the following tools:

• stopper;
• instant adhesive;
• hex key for furniture;
• screwdrivers of different sizes.

Screwdriver Set

Hex keys

Types of problems and their elimination

The sliding wardrobe is considered an integral part of any interior. They are characterized by smooth running and silent operation. The main advantages are practical use, compact storage of any things. The doors in the closet should not make any extraneous sound.

During regular use, backlashes often occur, smoothness is lost, door leaf warps or jumps off the guide rails.

It is necessary to carry out regular inspection of the mechanism, which will help to avoid serious damage and deformation of the mechanism. To learn how to adjust doors, you need to familiarize yourself with the most common causes of malfunctions. Below are instructions that will help you cope with this task. You can also watch video lessons from experts.

Door misalignment

This is a common problem that occurs due to sagging of one of the door leaf. A gap is formed at the top or bottom of the structure near the side wall of the cabinet. This deformation occurs when the adjusting screw is partially or completely out. It fixes the side edge in a vertical position. When the door moves, a slight vibration is created, which leads to this defect.

To adjust correct position doors, the following instructions must be observed:

• At the bottom of the side walls there is a bracket with two identical screws. If they are hidden under a special tape, then it must be peeled off without damaging its integrity;
• The slot (recess in the head of the fastener) of the lower screw is unscrewed with a hex key. It is designed to adjust the structure;
• turn the key in different directions and look at the result. The side of the structure will be lowered or raised. With one full revolution, the blade moves vertically by one millimeter.

Thanks to this adjustment, the distortion or resulting gap can be eliminated. At closed door you should choose the optimal position when the end and side posts are strictly parallel. The optimal gap between the bottom sash and the guide is strictly 6 mm.

The doors are a little warped

Finding the adjustment hole

We use a hex key

After adjustment, put the tape in place

Doors don't close tightly

When closed, the doors may not fit tightly together. They often roll back when closing. This defect appears even with a slight slope of the floor, which cannot be seen visually. In order for the wardrobe door panels to take their normal position, it is necessary to adjust the locking stopper.

The following guidelines must be followed:

• Adjustment of each sash strictly according to level. They should press tightly against the side of the cabinet;
• Marks are made on the guides where the center of the roller falls. Take into account the orientation and location of the adjustable blade;
• the doors move aside. Use a knitting needle or a screwdriver to move the stopper in the desired direction so that its center coincides with the marks made.

When the stopper is in the required position, when it comes into contact with the roller, the doors are locked in the correct position. They will fit tightly to the side of the wardrobe. If the design provides for several door leaves, then during regular use they displace the stoppers. In this case, it is necessary to adjust the stopper on each leaf.

Installing the stopper

Eliminating extraneous sounds

The wardrobe must open without any extraneous noise or sounds. Rail mechanisms move smoothly and without vibration. When a person hears unpleasant sounds and even a strong grinding noise, this indicates weakening of the fastening elements. The rollers on the top rail may become misaligned and cause noise and vibration.

With such deformation of the mechanism, it is prohibited to expand the upper rails. This will lead not only to its breakdown, but also to the failure of the entire system. To eliminate noise, it is necessary to adjust the roller mechanism, which ensures smooth movement of the sash. It is necessary to remove the doors and tighten the fasteners tightly. Particular attention is paid to the roller overhangs on each side. They should be the same.

If there is no overhang on one side, and there is also a skew of the roller, then this leads to extraneous noise. When the defect is not eliminated immediately, gradual deformation of the mechanism occurs. Sliding system may fail, so it will need to be completely replaced. If even slight noise or vibration appears when opening the sliding wardrobe, it is necessary to carefully inspect the mechanism to eliminate the cause.

Adjustment bolt location

Eliminating squeaks

Partial loss of valves

Each person may encounter a situation where the door leaf has jumped out of the bottom guide. Before making adjustments, it is necessary to determine at what point the doors fall out. Most common reason– this is a clogging of the guide. In this case, the roller may move in the other direction during operation.

During cleaning, you need to thoroughly clean the guides from various foreign objects.

Regular cleaning can prevent dirt accumulation and damage. Particular attention must be paid to the cleanliness of the rollers. Various debris can get wrapped up there. They are the ones that cause the mechanism to break down.

Roller brackets modern cabinets are divided into supporting and suspended. For the former, the wheels are located at the bottom of the door, for the latter they move along the upper guide. Sliding mechanism it is more complex than conventional hinges and requires more attention than swing wardrobes. We'll tell you how to adjust wardrobe doors at home, and you can do it yourself without calling a specialist.

Adjustment of the support bracket is done with one screw

Common system failures

The sliding wardrobe system consists of one or more doors, which move using rollers along running guides fixed at the bottom and top of the cabinet. To prevent the doors from hitting the walls, stoppers are provided in the design.

With prolonged use, the following problems occur:

• the door sagged over time;
• the stoppers are worn or dislodged;
• the doors were skewed;
• Uncharacteristic sounds appeared when closing and opening doors;
• upon impact, the canvas flew off the guides;
• The doors began to fit loosely.

With such a quantity possible malfunctions, it is better not to call a specialist, but to learn how to configure it yourself.

Door arrangement diagram

Door connection

Over time, the doors may sag and not close tightly. This may cause clothing to become soaked unpleasant odors, fall out. To prevent them from opening on their own, it is enough to adjust two elements.

Exhibiting Schlegel

Setting up doors with lower rollers (Raumplus, Absolut, Aristo, Krauss) is carried out in several stages:

1. First of all, it is necessary to peel off the fleecy seal located at the end of the sash on the left side. There is no need to tear it off completely. It is enough to peel off the tape by 30 cm.
2. There should be two adjustment holes and a bracket under the seal. The adjustment is carried out using a hexagon.
3. Turning the adjusting bolt clockwise raises the blade up, and turning it counterclockwise lowers it down.

Buying a wardrobe for a bedroom or hallway is a popular solution for storing things. At correct operation This furniture lasts a long time and problems rarely arise with it. But over time, the moving parts of the doors wear out and wear out without proper care. Because of this, sliding doors warp, open poorly, and jam. Some breakdowns require the presence of a technician, but many can be fixed on your own. Let's look at what wardrobe malfunctions you can fix yourself.

Why does the wardrobe make clicking noises?

Sometimes the roller mechanism makes clicking noises under the force of gravity of the moving sashes. Adjusting the roller mechanism will help get rid of them. To do this, remove the flaps, secure and adjust the roller. The roller mechanism must not be lubricated. Also check that the roller overhangs are the same on both sides. This will help get rid of extraneous sounds and at the same time carry out preventive maintenance of the sliding system.

Why is the wardrobe crooked?

If you can see with the naked eye that the door looks like a curved propeller, this is a factory defect. It needs to be changed. If the defect has arisen over time, then you should know that when the doors are opened frequently, backlash often occurs, which is why one of the doors sags. For this reason, the door leaf warps. To fix the problem, you need to adjust the rollers. There are long screws at the bottom on both sides of the doors, usually hidden under adhesive soft tape. It is moved aside and the screws are tightened so that the door is horizontal to the floor.

Why does the door jam?

A door can jam for several reasons:

• dust has accumulated in the rollers and guides;
• The rollers became unusable due to wear.

If the doors jam due to dust, you need to remove them, clean the rollers and rails with a soft cloth soaked in alcohol, remove any hair that has wound up on the rails, and install the doors back. If this does not help, you will have to change the rollers. To replace the rollers you will need special key, which is used to unscrew the hex screw.

Why doesn't the wardrobe close tightly?

Such a malfunction of the wardrobe, such as loose fitting of the doors when closed, can also be easily eliminated independently. This defect may appear if the floor is uneven. By adjusting the locking stop using a level, you will lock the doors in the correct position. If the door moves away from the wall, the fault is the displacement of the stopper in which the doors are installed. This mechanism is located in the middle of the bottom of the groove. Simply remove the sash and secure the stopper with superglue.

Why do the doors not move well?

Sometimes the doors are difficult to slide open. This malfunction of the wardrobe also appears due to the accumulation of dust and debris in the guides. If cleaning doesn't help, the problem is a loose roller. It needs to be adjusted or replaced with a new one. Unscrew it using a hexagon.

Why does the wardrobe open on its own?

Typically, this cause of wardrobe malfunction is due to deformation of the floor covering. Perhaps the floor sank near the closet. Under the bottom bar of most models there are adjustable feet. You can twist them to equalize the height. Also, the doors may begin to open due to the loosening of the guide fastenings. By tightening them, you will solve the problem with opening the doors independently.

If you decide to buy a wardrobe in Minsk, pay attention to the quality of the fittings. It is better to abandon the model with plastic guides, as they quickly fail. Steel or aluminum elements will last much longer; with them, you will not face wardrobe malfunctions for a long time.

To buy a wardrobe, go to TAM.BY: catalog companies will offer you how ready-made solution, so they will create individual design closet for you.

Such a relatively new element modern interior, like sliding doors, regardless of whether they serve to close a closet or are interior doors, require periodic qualified adjustment. At the same time, it is not necessary to be experienced in this matter, since it is quite simple to return the doors to proper operation, having only a minimal set of tools and knowledge. This article will describe how to adjust the sliding door so that after reading it, everyone can easily cope with this task with their own hands.

Adjusting wardrobe doors

First, let's look at the cases in which it may be necessary to adjust wardrobe doors:

• The door is skewed, in which a gap is formed in the upper or lower part between its end and the side wall of the cabinet at the junction.
• Incorrect operation of the locking device. In this case, the door being closed may open spontaneously or not close completely.

Let us examine in detail how to eliminate each of these problems.

How to eliminate a skewed sliding door

There are several types of fittings for sliding wardrobes, so there is no single adjustment method that is suitable for each of them. We will present instructions for adjusting the most common type of fittings, which are installed in wardrobes in most cases. So, the work is performed as follows:

1. From the bottom end of the problematic door, adjacent to the side wall of the cabinet, peel off the adhesive sealing tape (if any), thereby providing access to the adjustment hole.
2. Insert a hex wrench of a suitable size into the hole and rotate. If it is necessary to raise the adjustable edge of the door, turn the key clockwise; if lowered, turn it counterclockwise.

The need for raising or lowering can be determined by the location of the gap. If it is located in the upper part of the junction, this edge of the door must be lowered, if in the lower part, it must be raised.

1. After turning the hexagon in one direction or another, check the change in the gap. Reducing the gap will mean that the direction of adjustment is chosen correctly.
2. The adjustment is continued until the desired result is obtained, after which the seal is glued to its original place.

How to fix an opening wardrobe door

Holding the cabinet doors in place is achieved through a hardware element called a locking lock. It is a metal bracket that is inserted into a groove that serves as a guide for the door rollers. The bracket has 2 antennae, between which a recess is formed. Once in, the roller is fixed in place and thereby prevents the door from spontaneously rolling back.

The adjuster's task is to select the correct position of the stopper in the groove, as well as the optimal depth of the groove formed by the tendrils of the staple.

Adjustment in progress sliding door according to the following instructions:

1. Close the cabinet door all the way and mark the location of the door roller.
2. Open the door and move the stopper so that its recess coincides with the intended location. In this way, the door is secured in the desired position.
3. Next, adjust the depth of the recess formed by the antennae. Using, for example, a screwdriver, each antennae is gradually bent upward and the result is checked. As a result, when the door is closed abruptly, it should not open by inertia, but stop and lock in a given position.

Adjusting interior sliding doors

Operating principle of sliding doors interior doors often differs somewhat from what is described above. Here, the door rollers are attached to the upper end of the leaf and inserted into a bar fixed above the doorway. Installed door at the same time it is in a hanging position.

Adjustment sliding doors This type is to eliminate possible sagging of the door.

Sagging is eliminated as follows:

1. Dismantled decorative panel(platband) installed above the doorway, providing access to the rollers.
2. Find the adjusting element on the rollers and use open-end wrench of a suitable size, “pull” the door up. In this case, the friction of the door on the flag roller located in the groove of the lower end of the leaf and/or on the floor should disappear.

1. Check the position of the door after level adjustment.
2. Install decorative strip in place.

So, we looked at ways to adjust sliding doors. If you have a question about this material, you can put it in a comment under the article or ask a question to a specialist in the appropriate section.