DIY fishing table: some interesting ideas. DIY folding picnic table - drawings How to make a folding fishing table
A table for summer fishing is a very important thing. Without it, it’s basically a mess on the shore; you’re always looking for little things in the grass and preparing gear on your knee.
Therefore, I was actively interested in tables in stores and on the Internet, but came to the conclusion that the designer who would design a table to suit me had not yet been born. Sometimes small, sometimes tall, sometimes uncomfortable, sometimes unreliable. And those tables with legs cost a lot of money.
So I decided to do it myself table yourself, according to your requirements and with your own hands. I thought for a long time about coming up with something like this, so that it would be easy to manufacture, would not require the use of special tools, would be easy to use and transport, and would be inexpensive.
Until, by some miracle, I wandered into a Russian forum, where someone like me had already come up with everything and I just needed to borrow his idea and slightly change the design to fit the available materials. (Kowtow to the fraternal Russian people for the development)
It turned out to be good fishing table very simple and banal. All you need is an aluminum profile, sheet plastic (I used 5 mm PVC), a couple of hardware, a simple tool and the correct direction for the growth of your hands.
And this is what I got as a result of “painstaking work”:
Table for fishing in transport form
Dimensions - width 60 cm, length 40 cm, thickness 4 cm. Total weight 4 kg. Easily fits into a bag with a chair and does not require additional space during transportation.
In working position
For use there are two tabletops with an internal size of 54cm x 38cm. + Shelf for mobile, walkie-talkie, etc. There’s plenty of room to spread out and you don’t have to hold anything in your teeth or look for it in the grass.
The height adjustment of each leg allows you to cope with uneven shores. The profile sides prevent objects from falling off the table. Thanks to the possibility of lowering the center of gravity homemade table ik is not prone to capsizing.
It is also possible to use such a rod with hooks for deepening boilies and temporarily storing ready-made leashes.
On the other hand, it’s the same only without hooks - for towels.
Here's another use case
Single-story long table
Single-story wide table
Adjustment to the desired angle
Or, as a last resort, like this
Two separate tables
Includes 2 table tops, shelf, 2 rods, 8 legs.
During transportation, the tabletops become a pencil case into which all the parts are folded
To secure the threaded legs in aluminum profiles you can’t cut it, so I decided to use an M22 nut. Since it was planned to use legs with a diameter of 16 mm, this particular nut was purchased with internal diameter 17mm. (I hurriedly suffered in vain, the width of this nut is 30mm and inner size profile 27 mm. I had to file off 3 mm using sandpaper.)
With legs of 15 mm. it was possible to take a smaller nut, but in any case it is necessary to select it so that the nut is not too narrow for the internal profile size and the wall thickness allows for a normal thread to be screwed on. Next, drill holes in the nut and in the profile as shown in the figure.
In the nut, in one hole there is a thread cut for an M6 bolt, through the second hole the nut is attached to the profile using a rivet.
The profile is also attached with rivets along the perimeter to the PVC. The table is ready.
No special tools are required to make your own table of this design. We used everything that everyone should have normal person- a hacksaw for metal, a drill, drills, a file and a rivet gun.
A table for summer fishing is a very important thing. Without it, it’s basically a mess on the shore; you’re always looking for little things in the grass and preparing gear on your knee.
Therefore, I was actively interested in tables in stores and on the Internet, but came to the conclusion that the designer who would design a table to suit me had not yet been born. Sometimes small, sometimes tall, sometimes uncomfortable, sometimes unreliable. And those tables with legs cost a lot of money. So I decided to make a table myself, to suit my requirements and with my own hands. I thought for a long time about coming up with something like this, so that it would be easy to manufacture, would not require the use of special tools, would be easy to use and transport, and would be inexpensive.
Until, by some miracle, I wandered into a Russian forum, where someone like me had already come up with everything and I just needed to borrow his idea and slightly change the design to fit the available materials. (Kowtow to the fraternal Russian people for the development).
It turned out that making a good fishing table is very simple and trivial. All you need is an aluminum profile, sheet plastic (I used 5 mm PVC), a couple of hardware, a simple tool and the correct direction for the growth of your hands.
And this is what I got as a result of “painstaking work”:
Table for fishing in transport form
Dimensions - width 60 cm, length 40 cm, thickness 4 cm. Total weight 4 kg. Easily fits into a bag with a chair and does not require additional space during transportation.
In working position
For use there are two tabletops with an internal size of 54cm x 38cm. + Shelf for mobile, walkie-talkie, etc. There’s plenty of room to spread out and you don’t have to hold anything in your teeth or look for it in the grass.
The height adjustment of each leg allows you to cope with uneven shores. The profile sides prevent objects from falling off the table. Thanks to the ability to lower the center of gravity, the homemade table is not prone to tipping over.
It is also possible to use such a rod with hooks for deepening boilies and temporarily storing ready-made leashes.
On the other hand, it’s the same only without hooks - for towels.
Here's another use case
Single-story long table
Or this option
Single-story wide table
or this way
Adjustment to the desired angle
Or, as a last resort, like this
Two separate tables
Includes 2 table tops, shelf, 2 rods, 8 legs.
During transportation, the tabletops become a pencil case into which all the parts are folded
Assembled
To secure the threaded legs in aluminum profiles, you cannot cut them, so I decided to use an M22 nut. Since it was planned to use legs with a diameter of 16 mm, this particular nut with an internal diameter of 17 mm was purchased. (I hurriedly suffered in vain, the width of this nut is 30 mm and the internal profile size is 27 mm. I had to file off 3 mm with sandpaper.)
With legs of 15 mm. it was possible to take a smaller nut, but in any case it is necessary to select it so that the nut is not too narrow for the internal profile size and the wall thickness allows for a normal thread to be screwed on.
Next, drill holes in the nut and in the profile as shown in the figure.
In the nut, in one hole there is a thread cut for an M6 bolt, through the second hole the nut is attached to the profile using a rivet.
The profile is also attached with rivets along the perimeter to the PVC. The table is ready.
No special tools are required to make your own table of this design. Everything that every normal person should have was used - a hacksaw, a drill, drills, a file and a rivet gun.
If you have to put your fishing gear, baits and bait on the ground, then now is the time to purchase or make attachment table for fishing with your own hands. The cost of such a device in stores for fishermen is quite high, so you can simply adapt any folding table for these purposes. It is also quite easy to make such a table for fishing with your own hands.
A fishing table is an indispensable item for summer fishing. It can accommodate all the essentials: bait, bait and other fishing accessories.
Homemade fishing tables are divided into:Using a device such as a bait table, the fisherman does not need to be distracted, so he can concentrate entirely on the process of fishing.
- based on the materials of the legs and frame. For these purposes, metal or PVC materials can be used;
- according to the materials from which the tabletop is made. This can be a sheet of plastic, laminate, aluminum or galvanized;
- by design - simple (non-separable) and assembly tables, which have both their advantages and disadvantages. Fixed table small size more difficult to transport, as it requires more space than a folding one.
Having decided to make a special table for fishing with your own hands, you can be sure that it will meet all your needs.
When purchasing a table in a fishing store, it can be difficult to choose exactly what you need - in size, convenience and reliability.
For example, you can make a non-folding table from a plastic tray.
To do this you need to stock up:- A tray that will act as a table top. Select sizes based on your individual preferences, so that work surface All fishing gear could be accommodated.
- PVC tubes, which are used for laying electrical cables.
- Corners for attaching the legs of the attachment table.
- Plugs.
- Self-tapping screws.
From PVC pipes a frame for the tabletop is made, which is secured using self-tapping screws. Corners are attached to the edges of the frame, to which the legs are attached using glue or a soldering iron.
The easiest way is to make a fishing table from one section of an old shelf, shortening the legs to the required length.
Most often, aluminum is used to make an attachment table with your own hands. This material allows you to get a fairly durable and lightweight table. In this case, aluminum is used both for the corners and for the table top.
Such a necessary thing for a fisherman as fishing table can be done in several ways.
For the first, the following materials are required:- aluminum corner (for frame);
- aluminum pipes;
- window sill or metal sheet.
It is advisable to take the tubes different diameters, which will allow you to adjust the height of the table.
The second version of the fisherman's table involves making it from an aluminum sheet, without using corners. The edges on the working surface are made by folding the edges of a metal sheet.
To work you will need:- aluminum sheet;
- metal strip;
- metal pipe.
The legs are made from a metal tube, and the frame is made from strips.
The third option is a table with telescopic legs, which is intended mainly for winter fishing. It can also be easily upgraded by adding length to the legs or a special attachment to the fishing chair.
When going fishing light, you have to make do with minimal equipment. When fishing for a long time, it can be very inconvenient to constantly bend down to the ground to take bait, groundbait or other equipment. I suggest how you can quickly make a light table from cheap materials, weighing only 1.5 kg and with a load capacity of 10 kg.
Materials used
To make the table I used:- polypropylene water pipe – 2 m;
- aluminum tube d 8 mm – 2 m;
- pipe clips – 22 pcs.;
- food container with lid capacity 1 l;
- lid for a plastic box 510x380 mm;
- furniture mounting angles – 4 pcs.;
- pipe plugs – 4 pcs.;
- a package of M4 screws with nuts and washers;
- M5 dowels with self-tapping screws – 8 pcs.
Making a collapsible table
Will be used as a table top plastic cover for the container. To make the legs, you need to cut the polypropylene water pipe into 4 pieces of 50 cm each.
First you need to make fastenings for the legs of the table. To do this, you need to attach clips to furniture mounting corners. water pipes. They already have holes, so you just need to tighten everything with a screw, nut and washers. The resulting fastening is placed at the corners of the cover, and marks are made for the holes. They are burned through with a hot awl. After this, the supports are fixed to the tabletop.
Once the fastenings are ready, the legs can be put back in place.
Next you need to install spacers to add stability. To do this you need to cut aluminum pipe into pieces of suitable length. It is best if the spacers are a little larger, then the legs will become more stable.
You need to drive dowels into the ends of the tubes. Then the clips are screwed to them using wood screws.
The table is almost ready. It remains to improve the design a little. You need to press plugs into the ends of the legs to protect them from dirt.
To be able to fold the removed legs under the tabletop, you need to attach 4 clips along the narrow edge to it. Holes are drilled in the lid for fastening the clips with screws.
Now you can place transverse aluminum spacers diagonally under the tabletop, and clamp the legs themselves in clips.