DIY motor crafts. The simplest inverter from a motor without transistors

Make something useful out of useless children's toys or household appliances no problem for a master dreamer. And it’s good that many electrical appliances become outdated and break down. It makes no sense to send such things for repair - it’s easier to buy something new. And true “homemade people” are just waiting for this. They immediately have a whole bunch of ideas that require immediate implementation.

Second life of children's toys

There are times when a self-propelled toy breaks into pieces. Probably, in order to calm the child down, you urgently need to buy a new one? Not at all necessary. You just need to start the family process creative thinking. And to do this, remove the remaining usable parts from the broken car along with the motor. Then collect all the toys in the house and choose the one that can be brought to life again. Probably, you will need school knowledge in physics, chemistry and electrical engineering.

Repair of an old helicopter

Suddenly an old forgotten helicopter with an unusable engine and broken blades, which had long been lying on the mezzanine, caught my eye. He apparently was waiting for his finest hour and now with pleasure showed off the blue and white sides with the half-erased inscription “USSR-0098”.

Such things must be handled carefully. The old man doesn't like fuss. You will have to carefully remove the remains of the large main screw by unscrewing several small screws. To get into the engine compartment, you need to remove the plastic battery box from below. The engine is held on by three bolts and, as expected, has two wires “plus” and “minus”, which are connected through a chip block to the power switch. All this must be carefully unsoldered and unscrewed.

Pulling the engine out White light, you need to inspect it and compare it with the motor from the car. The fact is that 250 -270 rpm is enough to create lift. and power 1 - 2 watts. The difference in engine characteristics turned out to be small. Then you can safely install a fresh engine on the helicopter. And then go to the model shop for a brand new main rotor. When everything is ready, the repaired rotorcraft is tested in the presence of the entire creative family.

Modern children's helicopter models are repaired using the same scheme. Only now they are radio-controlled, and therefore you will have to fork out money for a control panel, on which the rotor speed and the speed of the helicopter depend.

New engine for toy car

In order to make a small children's car, you need: wheels, the car body itself, wires, a control panel, various electronic boards and a motor. If you have all this goodness, they begin to create a model. There is no need to look for the engine, since it is already there. The car body itself can be make it yourself made of wood or plastic and decorated to your taste. It’s good for those craftsmen who have a small 3D printer in their home that can build any shape of model.

Often the machine is made quite simply. They take a long-abandoned small children's car with wheels, disassemble it down to the screw and try to automate it using a ready-made motor. The following are used: glue, electrical tape, small gears from watches, gearboxes from old models and much more. And people for whom such fun has become a real hobby often achieve great success in making homemade motors.

When several new models of children's cars have been made and tested, all that remains is to do something generally useful. It is necessary to design a fan that would freshen the air and inspire new ideas. For this you need just a few items that are at hand. Namely:

• a motor from a children's toy (you can't go anywhere without it);
• CD discs, 6-7 pieces;
• plastic stopper from a bottle;
• cardboard tube approximately 10 cm high and 3 - 4 cm in diameter;
• switch;
• glue.

Manufacturing begins by cutting the disk into 8 equal parts from the edge to the center, not reaching approximately 1.5 cm from the hole. Then the resulting sections must be turned with one edge outward to form blades. The manufactured disk is placed on a plug, inside of which a hole is made for mounting on the motor.

Now they are making the leg and stand. A cardboard tube can easily pass for a leg. Wires and batteries will be hidden inside it. The remaining few disks can serve as an excellent stand. All this is glued well and painted in different shades. The fan is ready for operation.

Motorized ship

In order for the child not to hang out at the computer for days, he needs to be gradually accustomed to making various and interesting things that he can make with his own hands. Spring is coming, the streams will run, and you will need a small boat that will symbolize the coming long-awaited warmth.

Necessary materials The child will find it in his room. Here you need:

• AA batteries 3 pieces;
• polystyrene foam, electrical tape, glue;
• motor from a CD drive or toy;
• plastic cover from a lemonade bottle;
• two pieces of plastic and iron washers.

The first step is to make a propeller. Slots for the blades are prepared in the cork. Flat ice cream sticks are the finished blades of the future boat. Then a hole is made in the plug to fit this screw onto the motor. All this is well glued. The power plant is ready.

Next, the shape of the ship is cut out of the foam. The front part of the boat is made triangular, a place is prepared at the stern for a propeller with a motor, and in the middle there is a recess for batteries. Everything is connected and glued. They carry out tests in the bathroom and look forward to the first spring puddles.

Glider car

This is the most exciting toy created and tested by a child. On the ground, such a machine moves on wheels, and on the water on a special boat. Produced in 2 - 3 hours.

Necessary materials:

They are making a power plant. It is an engine with a propeller. The blades are cut using the neck of the bottle.

It should look like a rose. You can see from the photo that it is then screwed onto a plug attached to the motor.

Then they make the chassis. To do this, use a skewer. They put plugs on it that serve as wheels. They attach everything to a square bottle, inside of which the batteries are placed. Connect with wires according to electrical diagram. The glider is ready. If desired, you can replace the plastic propeller with a more rigid one. Then the driving performance of such a car will be appreciated not only by the designer himself, but also by his friends.

Crawling robot

Manufacturing the robot takes only a few hours. It's not quite the robot people imagine. He does not walk, does not swim, but crawls chaotically on a smooth surface. This effect is created due to the unbalanced rotation of the motor rotor. For real cars this leads to a tragic accident, but here it only causes a smile.

So, to create a robot you need a motor and a battery. A small oblong piece of foam plastic or foam cardboard is placed on the engine axis and glued. This serves as a destabilizer. To the very tip of it attach a decorative light element.

A battery is installed on top of the motor and covered with various interesting details. They make his legs out of toothbrushes, his eyes out of balls, decorate him with colored wire or paper clips, and so on. When turned on, the engine vibrates significantly, which causes the toy to crawl chaotically.

Other ideas

In addition to all of the above, motors are used in homemade products such as mini drills and drills. Such devices do not require unnecessary parts. They have one task - to rotate the fixed drill.

To do this, select a collet or regular chuck for the motor axis, which will clamp a small drill. Then solder the wires from the engine to the batteries through the switch. When the assembled device has successfully worked, it is placed in an antiperspirant case or some other case that is most suitable for a motor with batteries. All this small device fits in the palm of your hand. The switch is always located under the thumb.

Such devices are necessary for radio amateurs for drilling holes V printed circuit boards Oh. They can also be used by cabinetmakers who engage in fine volumetric wood carving. Only instead of a drill, they insert a finger micro-mill for sampling and grinding hard-to-reach places.

As you can see, with a little imagination and diligence, a child, with the help of his parents, can create truly original toys and other useful things.

We will send the material to you by e-mail

Scrap metal collectors will be happy to take your old washing machine. But don't rush to please them. You won't get much money for scrap, but if you approach this issue wisely, you can get a lot of useful things for household. Homemade engine from washing machine They will help you quickly de-feather a bird, cut up pet food, mow the lawn, smoke fish and meat. And this is not a complete list of what can be made from a washing machine. Today in the editorial review of the site detailed instructions, how to give the “heart of iron” from a washing machine a new life.

Parts from a washing machine are a material for many useful homemade products

If you are planning to make homemade products from a used engine, you need to figure out what it is and what it is capable of. In you can find three types of motors: asynchronous, brushless and commutated. Let's take a closer look at them:

• Asynchronous– can be two-phase or three-phase. Two-phase engines are found in older Soviet-made models. More modern machines are equipped with three-phase. The design of such an engine is extremely simple; it can reach speeds of up to 2800 rpm. The working engine removed from the machine just needs to be lubricated - and it is ready for new exploits.

• Collector– you will find this type of motor in the design of most household appliances. Such devices can operate from constant and alternating current, have compact dimensions and controlled speed. The only drawback of such an engine is the brushes that wear out, but these parts can be replaced if necessary.

• Brushless Direct Drive– the most modern engine from the Korean manufacturer. You will find it in modern washing machines from LG and Samsung.

Now that you can determine the type of motor, all that remains is to decide where you can use the motor from the washing machine.

We properly disassemble and decide what can be made from parts of an old washing machine

Disassembling a washing machine is a leisurely task. After working with water, a salt build-up may remain on the parts; it must be carefully removed so as not to damage the parts during removal. What can be made from an old washing machine? A motor will be useful for homemade projects - it will become the basis for many devices. The drum will also come into play. It is usually made of stainless steel. All pipes must be disconnected from the drum. A loading hatch may also be useful. In addition to these parts, do not rush to throw away springs, counterweights and body parts.

How to make a sharpener or grinding device from a washing machine engine

A sharpener is one of the most popular tools for the home. With its help you can sharpen gardening Tools, household knives and scissors. If you don’t already have one, buy it at any hardware store or make one grinder from the washing machine. The most difficult part is how to attach the sanding wheel to the motor. The easiest way is to buy a ready-made flange. It looks something like this.

You can machine a flange from metal pipe suitable diameter, most often a tube with a cross section of 32 mm is suitable. You need to cut a piece 15 centimeters long from it, this is quite enough to fix the emery. The flange is secured to the motor shaft by welding or a through bolt. The video describes in detail how a homemade washing machine sharpener works:

Making a wood lathe from a washing machine

What else can you do with the washing machine motor? One popular idea is a wood lathe. Let's look at the step-by-step process.

Illustration	Description of action
	To firmly fix the engine on the workbench, make fasteners from a metal angle. To do this, drill holes for fixing to the motor legs and table.
	To fasten a wooden part, you will need a flange fixed to the motor shaft, and these are the studs made from ordinary bolts with cut off heads. Screw these pins into the base. You will need 3 studs.
	The motor is fixed to the table with self-tapping screws and to the metal part with bolts.
	The opposite end of the wooden part is attached with such a device. It consists of a screw with a loop, two wooden stands perpendicularly fixed to the corners.
	This wooden part must be movable so that different workpieces can be used. For mobility, it is mounted on a threaded stud with bolts.
	To control the motor you will need a power supply. You can use one of the computer units. You will need to install switches to adjust the rotation speed.
	How to connect a motor to a power supply in animation.
	To guide your tools, make a tool rest. It consists of two wooden parts and a metal corner. All parts are movable due to fastening with one bolt.
	The lower part of the tool rest is rigidly fixed on the workbench using self-tapping screws and corners.
	The workpiece is fixed on the machine on both sides: on the left - on studs, on the right - on a bolt with a handle. To fix it in the workpiece, you need to drill the corresponding holes.
	To work, you will need sharpened tools - cutters.
	Final sanding of the workpiece is done using a strip of sandpaper.

How to make a simple feather removal machine for home use from a washing machine with your own hands

The time of slaughtering a bird is a troublesome stage. This is usually done in the fall, when the ducks and broilers have reached the desired weight, and it is no longer profitable to keep them in the winter. You need to pluck several dozen or even hundreds of carcasses very quickly. You can get rid of hard labor with the help of a feather removal machine, and it’s easy to do everything from the same parts of the washing machine.

The device does not require disassembling the washing machine. It is especially convenient to use machines with vertical loading. You just need to fix the beats in the drum so that they point inward. Before plucking, the chicken carcass must be scalded with boiling water and then simply thrown into a rotating drum. Here's what happens:

Important! To prevent water from getting on the engine of the feather removal machine, you need to protect it with a plastic casing.

And the last point - the feather removal device must be firmly fixed, since the vibration when loading the carcass will be very strong.

Lawnmower from a used motor

We continue to look for the answer to the question of where we can use the motor from an automatic washing machine. Another original idea is manufacturing. For small area An electric model connected to a power source with a cord is quite sufficient. The design of such a unit is very simple. You will need to make a platform on four wheels with a small diameter.

The engine is fixed on top of the platform, the shaft is threaded into the hole below, and the knife is attached to it. All that remains is to attach handles and a lever to the cart to turn the power on and off. If you have an asynchronous motor lying around, you will be surprised at how quiet the unit will be, even compared to factory models.

Advice! To prevent grass from wrapping around the knives, you need to slightly bend their cutting edges down.

Video: how to make a lawn mower

Animal feed cutter

For a rural resident, a feed cutter is a very important device on the farm. And this unit is easy to make from. What can be used: a drum and a motor.

For a feed cutter, you will need to make a housing in which a drum with holes sharpened for cutting and a lid for pressing will be mounted. The connection between the rotating drum and the motor is carried out through a drive. The finished model looks like this:

How to build a generator from an old washing machine

We continue to look at homemade products from a washing machine motor, and the turn has come to the generator. You won't be able to assemble a powerful device, but in the event of an emergency shutdown, you can be well prepared. To turn the engine into a generator, you will have to disassemble it and partially cut off the core. In the remaining part of the core you need to make grooves for neodymium magnets.

The gaps between the magnets are filled cold welding. To operate the device, the kit must include a motorcycle battery, a rectifier and a charge controller. Details of the work in the video:

Homemade concrete mixer

If you started minor repairs, which requires, for example, plastering walls, you will need a concrete mixer. Once again, washing machine parts will come in handy.

As a container for concrete, you can use the same drum with pre-sealed holes for draining water. It is best to use parts from a front-loading machine; there will be almost nothing to redo. To strengthen the body, use a metal corner, and for convenient movement of the concrete mixer, equip it with wheels. Main difficulty in the design - the manufacture of “swings” for the correct tilt and subsequent drainage of concrete. How to do it correctly in the video:

Homemade products from a washing machine engine: circular saw

You will be surprised, but a circular machine can also be built based on the motor from a washing machine. An important point in this matter is optional equipment motor with a device that regulates speed. Without this additional module, the circular machine will work unevenly and simply will not cope with the task. Device assembly diagram:

The principle of operation of the device is simple: the engine drives a shaft on which a small pulley is mounted. From the small pulley there is a drive belt to a large pulley with a circular saw.

Important! When working with a homemade circular saw, take care of your hands. All structural parts must be firmly fixed.

The resulting unit will not be very powerful, so it can only be used for cutting boards up to 5 cm thick. How this homemade circular saw works:

What else can be made from a washing machine drum: original decor ideas

The drum with its correct perforation is the material for manufacturing decorative items. Here are some interesting ideas.

Bedside tables and tables. Drums with doors from top-loading machines can be used to hide small items.

Making a barbecue from a drum from a washing machine, photo examples

- a temporary product. Sooner or later it burns out and requires replacement. You can buy a new one each time or use improvised material, for example, a drum from a washing machine. Making this craft from a washing machine drum takes a couple of minutes. The beauty is that oxygen easily enters the perforated container, which causes active combustion.

The metal of the drum can withstand a couple of seasons. Do it for him convenient stand, so that you don’t have to bend over, and you’re done. Skewers standard length conveniently placed on a small roasting pan. If necessary, you can lightly weld a couple of guides.

How to make a good smokehouse from a washing machine drum

The icing on the cake in our question is. Fragrant smoked meat, lard and fish - what could be better for the table? If you have a tank from a top-loading machine lying around in your shed or garage, consider it a done deal.

It is necessary to cut a hole in the bottom of the tank for the firebox, and weld fasteners inside for hanging food. All that remains is to install the tank on the fireplace, hang the fish or lard, cover the top of the tank with a lid and light the sawdust.

It is important that the fuel under the smokehouse smolders and does not burn. It is better to place such a device away from home.

Important! You'll have to keep an eye on this smokehouse. It cannot be left for a long time, the fire may flare up, and instead of a smoked product you will get a burnt product.

The need for a miniature tool exists where a person is engaged in the manufacture of souvenirs, models of ships and aircraft, small technical units and parts.

Miniaturization comes in two ways. The first option involves the production of only miniature tools - disks, cutters, etc. The second option involves the production of grinding tools based on miniature electric motors.

First option - Using a drill + (Video)

The first option has a simpler solution. Let's say we need to make a miniature grinding wheel, which will be installed in a drill or screwdriver. To do this we can take a broken disk. Draw a circle on it using a caliper required sizes. Then we cut out the future one along the drawn circle. miniature disk. In its center we drill a hole into which we insert a bolt with a diameter of 6 mm. We put the washer on the bottom and tighten it with a nut.

The bolt will be the axis of rotation of the disk. We insert it into the chuck of a drill or screwdriver and clamp it. With this tool you can cut materials in hard-to-reach places or those that have small sizes. Finished parts can be sanded.

It is easy to make a miniature cutter for cutting small parts from plastic or wood. To do this, take an ordinary tin stopper from glass bottle. In the center of it we make a hole for installing the axle. The same bolt with a diameter of 6 mm can serve as an axis. Align the edges of the cork and cut out the teeth. It is advisable to make minimal markings.

Such a cutter, loaded into a drill or screwdriver, can easily cut small wooden planks, for example, for modeling. Plastics also lend themselves to this simple tool.

Second option - Self-assembly + (2 videos)

If the task is to make a miniature instrument with your own hands, then you must initially select an electric drive. A motor from various devices- a printer, an old cassette recorder or from an ordinary children's electrified toy.

Depending on the power of the electric motor, you can build a mini grinder in two directions. The first direction is to use a network power source. For example, from old mobile phone. The second direction provides for a completely autonomous model consisting of a motor that will be powered by batteries or accumulators.

The difference between the two directions is in the design of the case. In the first case, space will only be required for the electric motor, and in the second, a battery compartment will need to be installed.

It is very convenient to use a segment for the body PVC pipes. If its diameter is slightly larger than the diameter of the electric motor, then electrical tape can be wound around the motor. You can secure the engine using a glue gun.

As plugs, you can use plugs that are placed on PVC pipes during transportation and storage. In the front plug it is necessary to make a hole for the motor shaft, and in the rear plug for the power wire. The power connector and switch must be secured to the housing.

The ideal option would be to attach some kind of collet clamp to the shaft. This will allow you to use standard burs, drills and non-standard mini cutters and discs. If installing a collet clamp does not work, you can connect the shaft and cutting tool using a double contact from the electrical block.

In a similar way, you can make a case for a mini angle grinder with autonomous power supply. Only after installing the engine in it, it is necessary to install the battery pack. The battery wires will be connected through a switch mounted on the case.

In both cases, on mini grinders you can use homemade instrument and standard industrial - burs and drills.

A compact homemade mini drill can be used for drilling printed circuit boards if you suddenly decide to assemble some. In addition, it is useful for ordinary household purposes, if there is a need to drill a small hole in wooden board or plastic. Working with such a tool is much more convenient than big drill or a screwdriver, since the mini version is much lighter and more compact, which allows you to minor work faster and better quality. Next, we will tell you how to make a mini drill from a motor with your own hands, providing photo instructions and visual videos examples

Method No. 1 – Second life for an old tape recorder

As you understand, the first version of a homemade mini drill will be made from a CD recorder forgotten by time. All you need from the former bestseller is a motor that will rotate the chuck with the tool. Since the device is powered by 6 Volts, you will additionally have to find an appropriate power supply or several batteries. You can use a USB adapter, but the power in this case will be slightly reduced. In addition, you need to buy a collet yourself (sold in any radio store or on the market, on the Internet on AliExpress, the price is low) and find a suitable housing for homemade work, although this is not necessary, you can hold the tool directly by the motor.

So, in order to make a mini drill from a motor yourself at home, you must follow these steps:

That's all the technology for assembling a device with your own hands. As you can see, making a microdrill from a motor is not at all difficult, even for a novice electrician. The only drawback of this device is the low strength of the thin drill. If you drill holes that are not at right angles, it will break immediately, so be careful and buy a few drills in reserve for practice.

Very important point, which you should know - to make the drill spin in the other direction, just swap the wires! Interesting video instructions on how to make a simple drill, you can see below:

A simple drill made from improvised means

Method No. 2 – Use the reel!

Another original way make a mini drill at home using a fishing rod reel. In this case, the assembly technology is quite simple, but the principle of operation itself will be based on mechanical rotation, you will get a mini-hand drill

To make a device with your own hands you will need:

• spinning reel;
• cartridge from old drill or a collet clamp of a suitable size;
• hot glue or cold welding;
• drill.

The assembly process is quite simple and consists of only two steps. The first step is to dismantle the spool with fishing line and cut off the remaining extra axis.
After this, the cartridge is glued to the remaining rod. You can do without a chuck and install a collet instead. When the glue has hardened, you can check the finished mini drill. You can see all the assembly details in this video example:

How to make your own micro drill from a coil

Method number 3 – Antiperspirant idea

Well, the last version of a homemade mini drill that we would like to provide to readers is using a cassette motor and an antiperspirant container. The advantage of this model is that it is controlled by a separate on/off button and has a convenient housing. This homemade product will be powered by regular block power supply, which must be selected based on the characteristics of the motor.

So, first you will need to prepare the following materials:

• motor from a tape recorder;
• suitable collet with drill;
• used antiperspirant;
• RCA socket for connecting power and a mating part for it;
• power unit;
• switch from an old carrier.

The first step is to make a mini drill according to the instructions provided at the very beginning: place the collet on the shaft and secure it with bolts. Next, the motor housing is installed in the antiperspirant. As you can see from the photo, the dimensions are ideal for installing the part. If the motor has free movement inside the housing, secure it with electrical tape and hot glue.

After this, you need to drill a hole in the top cover for the exit of the collet or the drill itself. At the same time, you need to make a hole in the bottom for the power connector. Using a utility knife, you also need to cut out a window for the switch, then solder all the elements of the circuit in series and install them in a place convenient for you.

The advantage of this version of a homemade mini drill is its convenient operation, small size and stylish appearance. We recommend doing this particular option at home, because it is the most convenient, safe and at the same time affordable.

Review different ideas on creation

Examples for inspiration

Above we have provided the 3 most popular options for a homemade micro drill for drilling printed circuit boards. We found a few more on the forums original ideas, which may inspire you to make your own, unique homemade product.

So, here is a photo of spare parts ideas for creating a mini drill with your own hands at home:

1. Glue gun handle for easy operation. The motor was taken from an old Canon printer. Power is supplied from a conventional charger.
   
   
2. Second life for a hairdryer. According to the inventor, this homemade product is assembled on the basis of a motor from an ordinary household hair dryer, which means it does not require special power supplies and has high power. However, do not forget about the danger of mains voltage, so a reliable housing and insulation of all connections are necessary. In a similar way, you can make a device from an old blender, leaving the handle untouched.
   
   
3. Toothbrush for drilling circuit boards. The next idea is to use a toothbrush as a mini drill. There are already batteries and a motor, you just need to cut it off top part and install the collet attachment.
   
   
4. A plastic bottle can also be successfully used as a housing for homemade drill, and the collet chuck is perfectly replaced by a special bushing, an analogue of which is found in terminal blocks for wires.
   
   
5. Another option with a toggle switch for convenient control. In this case, to drill holes on the signets, you will not need to constantly connect the power plug to the outlet. In addition, a comfortable handle will make the drilling process more comfortable.
   
   

That's all I wanted to tell you about how to make a mini drill from a motor with your own hands. As you can see, there is nothing complicated, and there are a limitless number of ideas for assembly. We hope that our photo examples and video instructions were useful and interesting for you. In addition, you can assemble a micro drill yourself using an old DVD drive, a screwdriver, an electric razor, and even a motor from a washing machine!

Every day creating something with your own hands is becoming more and more popular. So why not create a special thing when everything is conducive to it? While women are diligently engaged in embroidery, sewing, knitting, quilling, men can only tinker, repair, and improve.

What to make from a motor?

Some parts of equipment that is broken and unsuitable for further use can be used at home. Quite often, men have the question of what can be made from a motor. In fact, there are a lot of options, the main thing is patience, the ability to work with technology and imagination.

As one option, you can make an excellent fan from a motor. People also make cars, helicopters and other interesting things from this part. All that is needed for full-fledged work (especially for beginners) is special electronic circuits and radio spare parts. Of course, you cannot do this without self-confidence and patience. It’s not a fact that everything will work out the first time, but if you try, the result will be for a long time please the master.

Helicopter from a motor

Having decided what can be made from a motor, it is worth thinking about how this thing is created. Stores sell special diagrams and spare parts that will help you cope with this difficult task and sort out the details. Sometimes you can’t even wrap your head around it, from a motor, but in reality everything is very simple, you just need to pay due attention to this matter.

So, to make a solid helicopter, you need to stock up the following materials: models with drawings, tools, motor, glue, power supply and control panel. If the case is already ready, then all that remains is to place the motor in it and connect it to the control panel. After this, you need to try to start the helicopter, and then it will become clear whether it is ready for use or has some problems that need to be fixed. If you have any difficulties connecting the wires, it is better to contact knowledgeable person, otherwise the parts may be damaged.

Men are often interested in what can be made from a motor, other than a helicopter. Let's consider another option.

A car made from a motor

Making a car from a motor is very simple. To do this, you need circuits and boards, which are sold in special stores. After purchasing everything you need, you can get down to business. There are two options for making a machine: you can make the body yourself or buy a ready-made one, which will make the master’s work easier. By purchasing a set, a person receives car parts, wheels, wiring, spare parts, a control panel and the motor itself (if there is none). It is worth noting that this will cost more than buying a regular ready-made machine, but you can also get great pleasure from the process itself.

Thus, it is completely obvious how to make a car out of a motor - you just need to purchase a ready-made housing and place the main part of the car there. Don’t forget about the control panel, which needs to be properly connected to the toy. As a result, the person will receive homemade typewriter, which will be cooler than any store-bought one. In addition, it can be improved, repainted and decorated as your heart desires.

In addition to all of the above, the beauty of making a car from a motor is that the child will certainly appreciate all the efforts of the parent, after which he will be immensely happy. You can build a miracle car together with your children. This is a very entertaining and interesting activity. Let's look at what else can be made from a motor.

Fan

Do-it-yourselfers (that’s what some men call themselves) are constantly trying to absorb as much new information as possible in order to make something new. It is not at all surprising that they are interested in things from the motor. To successfully carry out this operation you will need main detail structures, battery, sleeve, bulb and two old blanks.

First, blanks are used (cut along the radius), then the blades must be bent carefully using fire. For the next stage of work, a champagne cork is perfect, which needs to be pulled onto the axis of the motor. After this, you need to attach the blades to it and build a stand for the fan. The motor and all other parts will be glued to the latter. So light and interesting way make a fan.

Conclusion

So it's clear that you can make a lot of amazing things out of a motor. The main thing is desire and patience. In addition, you should not be distrustful of fantasy and intuition. There is no need to be afraid of ruining the product! We advise beginners to use old unnecessary things (as in the case of a fan). Experiment, you will succeed!