Instructions for using the latest Navitel navigation program. How to use a car GPS navigator (installation, configuration and connection of the car navigator)

Navigation modules in currently manufactured Android smartphones are built in at the production assembly stage. As a rule, these useful additional devices not bad. Just turn on GPS using the settings menu and launch the downloaded “maps” application. In a couple of minutes the device will determine its location.

With GPS always on, determining coordinates will not take even one minute. However, sometimes this feature does not work in the android gadget. Most often, the problem lies in incorrect or completely absent GPS settings.

Required additional services

In order to determine your location, you use the satellite receiver in your smartphone, but it is recommended to set up auxiliary services. They run without any problems on an Android phone:

1. a-gps (a service that additionally loads location data from the Internet, using the services mobile operators. The determination accuracy of this option is of course worse, but thanks to its operation, accurate satellite determination is accelerated);
2. wi-fi;
3. EPO (a service from Mediatek that pre-calculates the movement in the orbits of navigation satellites.

However, the pre-installed EPO data in phones is designed for Asian countries and may only work with glitches in Europe. During 2012-2014, Mediatek began producing chipsets with excellent characteristics, which are now used in the brands Sony, LG, and HTC in their products. Thus, in Android smartphones with an MTK processor, there is a problem with navigation, which consists in the incorrect functioning of GPS).

The procedure for eliminating the causes of incorrect GPS operation in a phone or tablet

General settings

Application

Location Settings

NMEA LOG Settings

With a different version of the MTK processor, the procedure for setting up GPS on an Android smartphone or tablet may differ, but the essence remains the same.

Ten years ago, car GPS navigators were a curiosity in the domestic market of electronic devices. But today it’s difficult to surprise anyone with the presence of built-in systems in modern smartphones and tablets

General information about GPS

Most modern smartphones and tablets on the mobile device market today are equipped with a GPS module for determining location. This is a really convenient and advanced option. In addition to plotting a route for a car or bicycle on the ground, the GPS module will be able to determine its own location with high accuracy up to tens of meters. Along with this, the system makes it possible to turn on some programs or activate the reminder function on the phone when you are at a certain point globe. on Android?

The main disadvantage of GPS positioning

The main disadvantage of GPS positioning in a smartphone is the rapid drainage of the battery. In this regard important point The correct adjustment of the global positioning operating mode appears. Below we will discuss the basic tools for how to set up GPS on Android, as well as the principles of working in the engineering menu of a smartphone in case of incorrect functioning of the system.

Enabling GPS operating mode

To enable GPS navigation, you can use the notification panel of your smartphone. The enabled positioning system is displayed at the top of the screen in the form of a periodically flickering circle. To change or view how GPS functions, you need to go to the smartphone settings, then to the “Personal Data” section, from there to “Location” and select “Mode”. Typically, the operating system provides three options to choose from, including "By device sensors", "Battery saver" and " High accuracy". If we are talking about phones that use latest versions"Android", the menu may look slightly different. How to set up GPS on Android 5.1? In this case, the listed items will be named “By all sources”, “By network coordinates” and “By GPS satellites".

Highest level of GPS accuracy

The most accurate positioning option is the “High accuracy” or “Across all sources” mode. At the same time, with this operating procedure, battery consumption will be the most intense and rapid. In this mode, the system tries to determine the location by all means available to it, namely: GPS, Wi-Fi and using mobile networks. The smartphone will constantly evaluate the space for the presence of a signal and try to determine the location not only in open areas, but also indoors.

This operating procedure is also sometimes called A-GPS. His distinctive feature Compared to the work of conventional navigators, it is possible to obtain additional service information about satellites via an Internet connection. This speeds up the search for satellites and obtaining data on their signals.

Other modes of global positioning operation

Mode GPS operation“Battery saver” or “By network coordinates” is used to receive a signal exclusively from wireless networks. In this case, the GPS module is not used. Of course, in this mode the accuracy of position determination is somewhat deteriorated. At the same time, indoor position can be determined using Wi-Fi.

The operating mode “By device sensors” or “By GPS satellites” can only function in open areas in the absence of interference. In this case, the position of the object is determined using satellites. If interference occurs in the form of high-rise buildings or walls and ceilings of premises, the satellite signal will be lost and the position will no longer be determined. It would be appropriate to say that this article is about how to set up GPS on Android without the Internet. But it should be noted that such installations are also possible using World Wide Web. In this case, the Internet is used to correct the position if the signal from the satellites is not good enough.

The last operating mode is the most economical for the battery. In addition, you can disable determining your own position on the ground in the notification panel. If you need to get a route from point A to point B, you can turn on positioning and follow the prompts of the navigator built into your smartphone. If you need a personalized search for an object, you should give preference to the "Battery Saver" mode. Well, if the phone has a powerful and capacious battery, the user may well choose the most expensive method of operation, “High precision”. The methods described above are suitable for solving the problem of how to set up GPS on Android through the main menu of the device.

Configuration using the smartphone’s engineering menu

However, on some smartphone models, especially made in China based on MTK processors, connection difficulties or unstable communication may occur. There are even cases when the device does not determine the location of an object at all. This is due to incorrect settings GPS module for work in domestic geographical latitudes.

This software malfunction can be mitigated and GPS can be configured on Android through the engineering menu of the mobile device. It should be emphasized that this functionality can be used on devices on which the Root operating mode is activated, which gives the user the opportunity to manage the smartphone as developers.

Next, you should perform a series of sequential operations. First you need to turn on GPS and Wi-Fi and go outside or to the balcony of the room. After this, you will need to enter the engineering menu by entering the combinations on the phone keyboard: *#*#3646633*#*#, *#15963#* or *#*#4636#*#*. It should be noted that on different models On smartphones, the symbol combinations may be different, or even not suitable at all. Then, to solve the problem of how to set up GPS on Android, you can use the Mobileuncle ToolHero application, in which, after launching, select the desired item and enter the engineering menu.

Here the user will find several bookmarks, from which he must select Location, and then go to Location Based Service. In the EPO line, you must check the Enable EPO and Auto Download boxes. It should be clarified that EPO is a system file that contains information about the coordinates of GPS satellites and their lines of movement. This item is often deactivated on some phones.

Now you need to go back a step and select YGPS, and then go to the Satellites tab, in which the user will find a map of the position of the satellites in orbit. If satellites are displayed in red, this indicates that the mobile device sees them, but cannot receive a signal from them due to incorrect settings.

To fix this problem, you need to go to the Information section, click full, and after a few seconds AGPS restart. After this, you need to return to Satellites and wait until the satellite icons light up green. It is best to carry out this operation in an open area, since on the balcony, due to significant interference in the form of house walls and trees, the signal quality is much worse. The last step is to reboot your device, be it a smartphone or tablet. Thus, the most common ways to set up GPS on Android are discussed.

Hello everyone interested in our articles

After looking through a lot of materials and the most practical explanation, in a convenient and understandable language, I found in the cartoon Smeshariki series Pin - grain of sand. It is advisable to view this clipping from the cartoon, as it will clear up a lot of things in your head. Don't be afraid it won't take much time

From the cartoon you watched, you understood that for normal operation navigator, three satellites are enough. You’ve probably noticed more than once in the navigator display, when you pass tall buildings at a slow speed, that your car begins to jump on the roofs of houses or drives along a neighboring parallel street and the navigator begins to direct you in the wrong direction.
One satellite remains visible, which is either in front of the car or behind, unless you go to ram a house. So this satellite can correct you only along one axis, but with mixing you can’t do without assistants. Basically, this only happens when you get into a traffic jam or stand at every traffic light.

We got a little distracted, that is, we studied what it is GPS. And now we have to start purchasing a navigator. First of all, we need to learn how to use the device correctly.

The first action is whether we like it or not, we need to train the battery. A lot depends on its performance and many glitches arise. When purchasing, the battery shows a discharged state, naturally we put it on charge - correctly. But when removing it, we make a big mistake when we see from the indication that the battery is charged - this is a misconception. We take the instructions or operating manual and read - what is the capacity of the battery, as well as the charger current devices. A normal company writes itself how long the first charge cycle takes. On average, the first charge of such devices takes four hours.
In the following steps we discharge and charge the battery a couple of times, this also applies to lithium batteries. It’s only after such processes that your navigator begins to correctly indicate the battery charge or discharge. In the future, when connecting various communication modules, you will not experience interruptions in the device.

1 Method- this is a common method and applies to all navigators on any operating system. Go out into an open area where there was no wall of high-rise buildings along the perimeter of 100-200 meters. Within a minute, the navigator happily reports your location and in the future it will be easier for him to control your path even with one satellite.
But what a disappointment I was when the navigator began to determine my position for more than five minutes. I wanted to figure it out.
Since I have an Android operating system, everything turned out to be simple - I installed it with Google play application AndroidTS GPS Test Free and started testing. Under normal conditions, as in the screenshot below, the navigator determines your location instantly

And there are times when we have only one satellite above our heads, even in open areas, and at these moments our navigator begins to become dull. I was shocked, but the fact is, I even forgot to take screenshots. So I made views of the satellites from the balcony, the only visible part is the south.

The first screen shows that the two satellites are located almost in the same coordinate, so you don’t have to try to launch the navigator - it won’t find it. But with the advent of the third satellite, there is already a chance of determination. But even staying in the same place on the navigator display, you will constantly move, since there is not enough one more satellite in the other hemisphere of the sky. This is clearly visible in the bottom screen, that UFO icon is me. It turned out to be a cool roof hopper, the difference is one minute

Very often there are difficulties associated with setting up navigators. In addition, this is facilitated by the wide variety of models on sale. This article will discuss how to configure the navigator. As an example, the Prestigio model will be considered. Basically, modern navigators of this model are based on the WindowsCE4.2 operating system. In addition to the basic functions, the navigator has the ability to play video in MPEG4 format, as well as listen to music. For this purpose, the device has a slot for a memory card.

The design of the navigator is not spectacular. It is a black box made of matte plastic. In addition to slots for a memory card, the navigator has a slot for mini-USB and for connecting external device GPS antennas. The display reaches three and a half inches.

In connection with unsuccessful attempts by users to update the device software, the question arises of how to configure the navigator? It is worth knowing that no matter what old program is installed, changing it to another will not work. The navigator is a device that is not subject to software changes. The device from Prestigio uses the iGo 2006 system. And users are usually not satisfied with the fact that this program very old. By erasing it from the navigator’s memory in order to install a more advanced utility, they cannot subsequently return everything back, since the device simply stops responding to human actions.

Or maybe you want to know how to set up your Prestigio navigator? If you do not know the setup methods in advance, you can waste a lot of effort before this process is completed. Due to the fact that the device is not very popular among users, it is quite difficult to find information about it. But in reality there shouldn't be any problems. Quite often, users when deleting software The navigator manages to erase some very important files, including Autorun.inf.

To configure the navigator, you need to transfer to it the files that were deleted earlier. As an example, you can borrow the same navigator from someone or find a list of what should be on the device and then download from it Required documents. These files can also be obtained from the owner of the same navigator model.

But that's not all. In order to finally configure the navigator, you should set the GPS receiver port in the options. To perform this procedure, you must run an automatic search. After this, the navigator will detect the required satellite and the device will begin to work. It is worth understanding that the program may differ from the previous one only in version. In other words, if the iGo2006 program was previously installed on the navigator, then after removing it you can install the iGo2008 version.

From all of the above it follows that you can configure the navigator by simply downloading all the necessary files to the device. If you have a question about how to configure, you can also use this method.