Matrix 2 k connection diagram. Instructions for connecting and programming the standalone Iron Logic Matrix-II K controller
Programming
standalone controller
Iron Logic Matrix-II K, somewhat reminiscent of the KTM-600 from Vizit, but more like the DLK-645/IPR8. The main functions can be programmed using a master key (card) - long and short touches as indicated in the table, as well as from jumpers that are on the case.Programming the Iron Logic Matrix-II K controller using a master card.
1. Adding simple cards. 1 DM
2. Adding blocking cards. 1 DM
3. Adding master cards. 1 k M, 1 d M
4. Erasing individual cards. 2 k M, 1 d M
5. Erase all cards (controller memory). 3 kM, 1 dM
6. Setting the door opening time. 4 to M
7. Switch to “Block” mode. 1 D B
8. Switch to “Assert” mode. 5 k M
9. Write the reader memory to the P51996 key. 1 k M, 1 d M
11.Write from 031996 to the reader memory. In first power-on mode with an empty base
Designation
1...5 number of touches;
d- long touch (hold the card for about 6 seconds);
To- short touch (hold the card for less than 1 second);
M - master card;
P - simple map;
B - blocking card.Jumper programming
To record new access keys, it is not necessary to have a master key. position No. 3. Programming jumpers are set when the power is off.
Position No. 1- lock type:
- without jumper -electromagnetic lock;
- with jumper -electromechanical.
Position No. 2- erasing all information from
controller memory.
Position No. 4- regular place of work
does not affect.
Regulation No. 5- trigger.
Connection diagram Iron controller Logic Matrix-II K
Connectionintercomsto the Iron Logic Matrix-II controller K access control systemscarried out by connecting the panel relay contacts (two wires) to "book open doors" and "ground (-)" terminal blocks of the controller board, that is, parallel to the exit button. The same thing needs to be done if you need to connectradio controller.
Also, do not forget that for uninterrupted operation of controllers from any manufacturer, you can useuninterruptible power supplies with various batteries.
You can always order installation and purchase any controllers from usaccess control systems for home and office .
By calculating the cost of installation andlaying cables and wires For access controlcontact us at the phone number below.
tel. 0636650232
Copying site materials is prohibited without a link to the Montag-security website
Programming the Iron Logic Matrix-II K controller using a master card.
1. Adding simple cards. 1 DM 2. Adding blocking cards. 1 DM
3. Adding master cards. 1 k M, 1 d M
4. Erasing individual cards. 2 k M, 1 d M
5. Erase all cards (controller memory). 3 kM, 1 dM
6. Setting the door opening time. 4 to M
7. Switch to “Block” mode. 1 D B
8. Switch to “Assert” mode. 5 k M
9. Write the reader memory to the P51996 key. 1 k M, 1 d M
11.Write from 031996 to the reader memory. In first power-on mode with an empty base
Designation
1...5 number of touches;
d- long touch (hold the card for about 6 seconds);
To- short touch (hold the card for less than 1 second);
M - master card;
P - simple map;
B - blocking card.Jumper programming
To record new access keys, it is not necessary to have a master key. position No. 3. Programming jumpers are set when the power is off.
Position No. 1- lock type:
- without jumper -electromagnetic lock;
- with jumper -electromechanical.
Position No. 2- erasing all information from
controller memory.
Position No. 4- regular place of work
does not affect.
Regulation No. 5- trigger.
Connection diagram Iron controller Logic Matrix-II K
Other controller connection schemes are also possible, for example when working with
intercom systems , radio controllers.Connectionintercomsto the Iron Logic Matrix-II controller K access control systemscarried out by connecting the panel relay contacts (two wires) to "book open doors" and "ground (-)" terminal blocks of the controller board, that is, parallel to the exit button. The same thing needs to be done if you need to connectradio controller.
Also, do not forget that for uninterrupted operation of controllers from any manufacturer, you can useuninterruptible power supplies with various batteries.
That's all there is to it programming and connecting stand-alone controllers from Iron Logic Matrix-II
K .You can always order installation and purchase any controllers from usaccess control systems for home and office .
By calculating the cost of installation andlaying cables and wires For access controlcontact us at the phone number below.
You can contact our specialists who will select the necessary equipment for you and, if necessary, lay the appropriate cables.
Our prices will please you, don’t hesitate to call us and we’ll make an agreement.
tel. 0636650232
Copying site materials is prohibited without a link to the Montag-security website